OBJECTIVES: To evaluate zirconia as a substitute for gold alloy in primary crowns facing secondary crowns manufactured with different materials, in terms of long-term retention force changes, wear, and phase transformation was aimed. MATERIALS AND METHODS: A total of 12 groups, each containing six samples, consisting of gold alloy primary crown-electroformed gold secondary crowns (AA), zirconia primary crown-electroformed gold secondary crowns (ZA) and zirconia primary crown-casted non-precious alloy secondary crowns (ZC) with conus angles of 0°, 2°, 4°, and 6° were evaluated. Samples were subjected to 10,000 insertion-separation cycles in artificial saliva and retention force was measured. X-ray diffraction and scanning electron microscope analysis were performed on the sample surfaces. RESULTS: The highest retention forces were obtained from ZC-0° group (72.09-71.26 N) and the lowest were obtained from ZA-4° (12.73-19.44 N) and ZA-6° (5.36-19.73 N) groups in the beginning and after 10,000 cycles, respectively. Retention force increased as the conus angle decreased. The monoclinic phase ratio of the zirconia primary crowns decreased after the experiments. No wear was observed in zirconia primary crowns except for the ZC-0° and ZC-2° groups. The use of zirconia primary crowns resulted in a less excursive retention force. CONCLUSIONS: A more predictable and less excursive retention force can be obtained using a hard and rigid primary crown material like zirconia. CLINICAL RELEVANCE: Despite a lack of knowledge about the aging of zirconia without a veneer layer in the oral environment, zirconia primary crowns are more advantageous in terms of retention force development and wear.
OBJECTIVES: To evaluate zirconia as a substitute for gold alloy in primary crowns facing secondary crowns manufactured with different materials, in terms of long-term retention force changes, wear, and phase transformation was aimed. MATERIALS AND METHODS: A total of 12 groups, each containing six samples, consisting of gold alloy primary crown-electroformed gold secondary crowns (AA), zirconia primary crown-electroformed gold secondary crowns (ZA) and zirconia primary crown-casted non-precious alloy secondary crowns (ZC) with conus angles of 0°, 2°, 4°, and 6° were evaluated. Samples were subjected to 10,000 insertion-separation cycles in artificial saliva and retention force was measured. X-ray diffraction and scanning electron microscope analysis were performed on the sample surfaces. RESULTS: The highest retention forces were obtained from ZC-0° group (72.09-71.26 N) and the lowest were obtained from ZA-4° (12.73-19.44 N) and ZA-6° (5.36-19.73 N) groups in the beginning and after 10,000 cycles, respectively. Retention force increased as the conus angle decreased. The monoclinic phase ratio of the zirconia primary crowns decreased after the experiments. No wear was observed in zirconia primary crowns except for the ZC-0° and ZC-2° groups. The use of zirconia primary crowns resulted in a less excursive retention force. CONCLUSIONS: A more predictable and less excursive retention force can be obtained using a hard and rigid primary crown material like zirconia. CLINICAL RELEVANCE: Despite a lack of knowledge about the aging of zirconia without a veneer layer in the oral environment, zirconia primary crowns are more advantageous in terms of retention force development and wear.
Authors: Sharon S Brown; Douglas D Green; Giuseppe Pezzotti; Thomas K Donaldson; Ian C Clarke Journal: J Biomed Mater Res B Appl Biomater Date: 2008-05 Impact factor: 3.368
Authors: Franz Sebastian Schwindling; Franziska Lehmann; Sophia Terebesi; Nicoleta Corcodel; Andreas Zenthöfer; Peter Rammelsberg; Thomas Stober Journal: Clin Oral Investig Date: 2017-02-11 Impact factor: 3.573
Authors: Franz Sebastian Schwindling; Ulrich Karl Deisenhofer; Anne-Christiane Séché; Franziska Lehmann; Peter Rammelsberg; Thomas Stober Journal: Clin Oral Investig Date: 2016-06-09 Impact factor: 3.573