Deoggyu Seo1, Youngah Yi, Byoungduck Roh. 1. Department of Conservative Dentistry, Yonsei University, Seodaemun-Gu, Seoul, Republic of Korea.
Abstract
OBJECTIVES: The purpose of this study was to evaluate the marginal and internal gaps in Cerec3 partial ceramic crowns (PCCs) of three different preparation designs in vitro using microcomputed tomography (microCT). METHODS: Cerec3 PCCs of three different preparation designs (n=20) were fabricated according to the following: Group I-conventional functional cusp capping/shoulder preparation, Group II-horizontal reduction of cusps and Group III-complete reduction of cusps/shoulder preparation. After fixation of PCCs, the microCT scanning was performed. For obtaining the average internal gap (AIG), the microCT sections were reconstructed 3-dimensionally, and then the total volume of the internal gap was divided by the contact surface area. The 2-dimensional (2D) microCT views were used to investigate the gaps at predetermined key positions in seven bucco-lingual sections and three mesio-distal cross sections. The gaps were measured using the microCT at each reference point. Statistical analysis was performed using one-way ANOVA and Tukey's test. RESULTS: For the 3D reconstruction technique, the AIGs were as followed: Group I 197.3+/-48.2microm, Group II 171.2+/-45.1microm, and Group III 152.7+/-27.1microm. For the 2D microCT views, the gaps of each group were the smallest on the margins ranging from 35.4+/-32.2 to 128.4+/-69.5microm, and the largest on the horizontal or angle walls ranging from 184.5+/-41.2 to 406.5+/-176.1microm. According to the results, Group I showed larger marginal and internal gaps compared with the other groups. CONCLUSIONS: For the PCCs, the simplified designs (Groups II and III) demonstrated superior results compared to the traditional cusp capping design (Group I). The marginal gaps were smaller than the internal gaps in all groups.
OBJECTIVES: The purpose of this study was to evaluate the marginal and internal gaps in Cerec3 partial ceramic crowns (PCCs) of three different preparation designs in vitro using microcomputed tomography (microCT). METHODS: Cerec3 PCCs of three different preparation designs (n=20) were fabricated according to the following: Group I-conventional functional cusp capping/shoulder preparation, Group II-horizontal reduction of cusps and Group III-complete reduction of cusps/shoulder preparation. After fixation of PCCs, the microCT scanning was performed. For obtaining the average internal gap (AIG), the microCT sections were reconstructed 3-dimensionally, and then the total volume of the internal gap was divided by the contact surface area. The 2-dimensional (2D) microCT views were used to investigate the gaps at predetermined key positions in seven bucco-lingual sections and three mesio-distal cross sections. The gaps were measured using the microCT at each reference point. Statistical analysis was performed using one-way ANOVA and Tukey's test. RESULTS: For the 3D reconstruction technique, the AIGs were as followed: Group I 197.3+/-48.2microm, Group II 171.2+/-45.1microm, and Group III 152.7+/-27.1microm. For the 2D microCT views, the gaps of each group were the smallest on the margins ranging from 35.4+/-32.2 to 128.4+/-69.5microm, and the largest on the horizontal or angle walls ranging from 184.5+/-41.2 to 406.5+/-176.1microm. According to the results, Group I showed larger marginal and internal gaps compared with the other groups. CONCLUSIONS: For the PCCs, the simplified designs (Groups II and III) demonstrated superior results compared to the traditional cusp capping design (Group I). The marginal gaps were smaller than the internal gaps in all groups.
Authors: A M Pabst; C Walter; L Grassmann; M Weyhrauch; D D Brüllmann; T Ziebart; H Scheller; K M Lehmann Journal: Clin Oral Investig Date: 2013-08-31 Impact factor: 3.573