H Y Chen1, J Manhart, R Hickel, K H Kunzelmann. 1. Department of Restorative Dentistry, Dental School of the Ludwig-Maximilians University, Goethe Street 70, 80336, Munich, Germany. hchen@dent.med.uni-muenchen.de
Abstract
OBJECTIVE: Determination of the polymerization contraction stress of packable composites (ALERT, Surefil, Solitaire, Solitaire 2) and a packable ORMOCER material (Definite) in comparison with a conventional hybrid composite (Tetric Ceram). METHODS: Contraction force generated by the test materials (10 replications each) was measured by polymerizing the composites filled in a plastic tray between two aluminum attachments mounted in a Stress-Strain-Analyzer testing machine (specimen size: 4x4x2 mm, C-factor=0.33). Contraction force was recorded for 300s under a standard exposure condition (40s, 800mW/cm(2)). Maximum contraction stress (MPa), force rate (N/s), relative force rate (%/s) of each material were statistically analyzed by ANOVA (alpha=0.05) and post-hoc Tukey's test. RESULTS: Maximum contraction stresses of the packable materials were 4.60 +/- 0.32MPa (ALERT), 4.16 +/- 0.18MPa (Definite), 3.36 +/- 0.08MPa (Solitaire 2), 3.33 +/- 0.23MPa (Solitaire) and 3.13 +/- 0.18MPa (Surefil), which were significantly higher than that of Tetric Ceram (2.51 +/- 0.14MPa). Tetric Ceram exhibited the significantly lowest force rate. Force/time curves were S-shaped. Solitaire especially showed a longer pre-gelation phase before contraction force was recorded. SIGNIFICANCE: High contraction stress and rapid contraction force development can lead to failure of bond to tooth structure. This study suggested that, packable composite resins are less capable of reducing the contraction stress during the early setting stage, thus not superior in maintaining the bond with cavity walls to conventional hybrid composite Tetric Ceram.
OBJECTIVE: Determination of the polymerization contraction stress of packable composites (ALERT, Surefil, Solitaire, Solitaire 2) and a packable ORMOCER material (Definite) in comparison with a conventional hybrid composite (Tetric Ceram). METHODS: Contraction force generated by the test materials (10 replications each) was measured by polymerizing the composites filled in a plastic tray between two aluminum attachments mounted in a Stress-Strain-Analyzer testing machine (specimen size: 4x4x2 mm, C-factor=0.33). Contraction force was recorded for 300s under a standard exposure condition (40s, 800mW/cm(2)). Maximum contraction stress (MPa), force rate (N/s), relative force rate (%/s) of each material were statistically analyzed by ANOVA (alpha=0.05) and post-hoc Tukey's test. RESULTS: Maximum contraction stresses of the packable materials were 4.60 +/- 0.32MPa (ALERT), 4.16 +/- 0.18MPa (Definite), 3.36 +/- 0.08MPa (Solitaire 2), 3.33 +/- 0.23MPa (Solitaire) and 3.13 +/- 0.18MPa (Surefil), which were significantly higher than that of Tetric Ceram (2.51 +/- 0.14MPa). Tetric Ceram exhibited the significantly lowest force rate. Force/time curves were S-shaped. Solitaire especially showed a longer pre-gelation phase before contraction force was recorded. SIGNIFICANCE: High contraction stress and rapid contraction force development can lead to failure of bond to tooth structure. This study suggested that, packable composite resins are less capable of reducing the contraction stress during the early setting stage, thus not superior in maintaining the bond with cavity walls to conventional hybrid composite Tetric Ceram.
Authors: T C Fagundes; T J E Barata; E Bresciani; D F G Cefaly; M F F Jorge; M F L Navarro Journal: Clin Oral Investig Date: 2006-07-06 Impact factor: 3.573
Authors: Lawrence Gonzaga Lopes; Eduardo Batista Franco; José Carlos Pereira; Rafael Francisco Lia Mondelli Journal: J Appl Oral Sci Date: 2008 Jan-Feb Impact factor: 2.698