Literature DB >> 24980803

Color stability of denture teeth and acrylic base resin subjected daily to various consumer cleansers.

Audrey Moon1, John M Powers, Sudarat Kiat-Amnuay.   

Abstract

OBJECTIVE: This study evaluated color stability of acrylic denture teeth and base resins after 48 weeks of commercial denture cleanser simulation.
MATERIALS AND METHODS: Two brands of denture teeth (Trubyte Portrait IPN, TP; SR Vivodent DCL, SR) in shades A1, B1, and C1 and three acrylic base resins (Lucitone, LU; Paragon, PA; Valplast, VA) prepared to manufacturer's specifications were exposed 10 hours daily to four cleansers (Clorox Bleach, CB; Polident 3 minute, PO3; Efferdent, EF; and Kleenite, KL) and distilled water control, approximating consumer overnight use. Color measurements used the standard Commision International de l'Eclairage (International Commission on Illumination, CIE L*a*b*) color space (0, 4, 12, 24, 36, and 48 weeks.) Color differences (ΔE*) at 48 weeks were subjected to four-way analysis of variance (ANOVA). Mean values were compared with Fisher's (protected least significant difference) intervals (0.05 significance level).
RESULTS: Mean color differences (ΔE*) demonstrated color changes in each material. ANOVA-indicated color changes in teeth were significantly affected by both cleansers and teeth brand (p < 0.05), but not shade. Color changes in base resins were significantly affected by cleansers (p < 0.05), but not brand alone. Overall, KL produced the least color change while CB and PO3 produced the most for all materials.
CONCLUSIONS: After 48 weeks of daily simulation, TP teeth were more color stable than SR in all cleansers except EF (p < 0.0001). Base resin VA was less color stable than LU and PA. Cleanser KL resulted in the lowest color changes. CLINICAL SIGNIFICANCE: All tested materials yield clinically acceptable color changes (ΔE* < 3.5); all cleansing methods tested can be recommended, although Kleenite demonstrated the least change after 48 weeks.
© 2014 Wiley Periodicals, Inc.

Entities:  

Mesh:

Substances:

Year:  2014        PMID: 24980803      PMCID: PMC4138258          DOI: 10.1111/jerd.12109

Source DB:  PubMed          Journal:  J Esthet Restor Dent        ISSN: 1496-4155            Impact factor:   2.843


  35 in total

1.  Color stability of visible light-cured, hard direct denture reliners: an in vitro investigation.

Authors:  G L Polyzois; S A Yannikakis; A J Zissis
Journal:  Int J Prosthodont       Date:  1999 Mar-Apr       Impact factor: 1.681

Review 2.  Denture base resins: comparison study of color stability.

Authors:  K B May; M E Razzoog; A Koran; E Robinson
Journal:  J Prosthet Dent       Date:  1992-07       Impact factor: 3.426

3.  Color stability of ten resin-based restorative materials.

Authors:  Camila Sabatini; Marc Campillo; Jamil Aref
Journal:  J Esthet Restor Dent       Date:  2011-06-10       Impact factor: 2.843

4.  Assessment of flexural strength and color alteration of heat-polymerized acrylic resins after simulated use of denture cleansers.

Authors:  Sandra Sato; Márcia Rosa Sobreira Cavalcante; Iara Augusta Orsi; Helena de Freitas Oliveira Paranhos; Osvaldo Zaniquelli
Journal:  Braz Dent J       Date:  2005

5.  Intraoral determination of the tolerance of dentists for perceptibility and acceptability of shade mismatch.

Authors:  R Duane Douglas; Tad J Steinhauer; Alvin G Wee
Journal:  J Prosthet Dent       Date:  2007-04       Impact factor: 3.426

6.  Critical appraisal. Color in dentistry: match me, match me not.

Authors:  Rade D Paravina
Journal:  J Esthet Restor Dent       Date:  2009       Impact factor: 2.843

7.  Colour changes in acrylic teeth--comparison of an objective and subjective method.

Authors:  R Liberman; E C Combe; V Piddock; D C Watts
Journal:  J Oral Rehabil       Date:  1996-07       Impact factor: 3.837

8.  Color stability of dental composite resin materials for crown and bridge veneers.

Authors:  I E Ruyter; K Nilner; B Moller
Journal:  Dent Mater       Date:  1987-10       Impact factor: 5.304

9.  Sanitization of dentures by several denture hygiene methods.

Authors:  T C Moore; D E Smith; G E Kenny
Journal:  J Prosthet Dent       Date:  1984-08       Impact factor: 3.426

10.  Effect of denture cleansers on the surface roughness and hardness of a microwave-cured acrylic resin and dental alloys.

Authors:  Renata Cunha Matheus Rodrigues Garcia; de Souza Joane Augusto; Rodrigo Nunes Rached; Altair Antoninha Del Bel Cury
Journal:  J Prosthodont       Date:  2004-09       Impact factor: 2.752

View more
  8 in total

1.  Colour stability of heat and cold cure acrylic resins.

Authors:  Pavan Kumar Bohra; P R Ganesh; Madan Mohan Reddy; A V Rajesh Ebenezar; G Sivakumar
Journal:  J Clin Diagn Res       Date:  2015-01-01

2.  Effects of thermocycling and various drinks on the color stability of heat-polymerized acrylic resin.

Authors:  Pinar Altinci; Pinar Durkaya
Journal:  J Istanb Univ Fac Dent       Date:  2016-10-01

3.  Color Stability of Heat-cure Acrylic Resin Subjected to Simulated Short-term Immersion in Fast-acting Denture Cleansers.

Authors:  K Lohitha; M Prakash; A Gopinadh; A J Sai Sankar; C H Sandeep; B Sreedevi
Journal:  Ann Med Health Sci Res       Date:  2016 Sep-Oct

4.  A Comparison of the Color Stability of Conventional and CAD/CAM Polymethyl Methacrylate Denture Base Materials.

Authors:  Cagatay Dayan; Melahat Celik Guven; Burc Gencel; Canan Bural
Journal:  Acta Stomatol Croat       Date:  2019-06

5.  Evaluation and Comparison of the Effects of Persulfate Containing and Persulfate-free Denture Cleansers on Acrylic Resin Teeth Stained with Cigarette Smoke: An In Vitro Study.

Authors:  Meena Varshini K; Deepshika Selvakumar; Madhan Kumar Seenivasan; Shanmuganathan Natarajan; Parthasarathy Natarajan; Prathibha Saravanakumar
Journal:  Cureus       Date:  2020-03-18

6.  Color Stability and Surface Properties of PMMA/ZrO2 Nanocomposite Denture Base Material after Using Denture Cleanser.

Authors:  Mohammed M Gad; Reem Abualsaud; Shaimaa M Fouda; Ahmed Rahoma; Ahmad M Al-Thobity; Soban Q Khan; Sultan Akhtar; Khalid S Al-Abidi; Mohamed S Ali; Fahad A Al-Harbi
Journal:  Int J Biomater       Date:  2021-04-07

7.  Colour Stability of 3D-Printed and Prefabricated Denture Teeth after Immersion in Different Colouring Agents-An In Vitro Study.

Authors:  Mariya Dimitrova; Bozhana Chuchulska; Stefan Zlatev; Rada Kazakova
Journal:  Polymers (Basel)       Date:  2022-07-31       Impact factor: 4.967

8.  In vitro Effects of Lemongrass Extract on Candida albicans Biofilms, Human Cells Viability, and Denture Surface.

Authors:  Petrus L B Madeira; Letícia T Carvalho; Marco A B Paschoal; Eduardo M de Sousa; Eduardo B Moffa; Marcos A Dos Santos da Silva; Rudys de Jesus Rodolfo Tavarez; Letícia M Gonçalves
Journal:  Front Cell Infect Microbiol       Date:  2016-06-28       Impact factor: 5.293

  8 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.