OBJECTIVE: In the process of anterior cervical fusion, little is known about the biomechanics of anterior cervical screw pullout. In this study, three different aspects of cervical screw fixation were evaluated: self-tapping (ST) versus self-drilling (SD) screws, the effect of screw geometry (length, diameter, thread pitch), and the use of rescue screws. METHODS: Nine screws consisting of different diameters, lengths, and thread pitch (cancellous and cortical) were tested in peak pullout force in an artificial bone model using an MTS 858 Mini Bionix test system. Rescue screws (4.5 mm) were then inserted in the failed holes of 4.0-mm screws and extracted to determine their holding strength. RESULTS: Length of screws and thread pitch both had a significant effect on the pullout force. Each 1 mm of increased screw length translates to 16 N of increased force to pullout in the foam bone model. Pullout strength did not vary significantly according to screw diameter or between SD and ST screws. However, the SD screw has an advantage because it can decrease the length of surgery. A decrease in pullout force of between 43% and 70% was found when using rescue screws. CONCLUSIONS: In situations in which the use of rescue/salvage screws is required, the surgeon should anticipate a significant decrease in the holding force compared with the original screw. Future directions for research include an evaluation of pullout force for screw and plate constructs.
OBJECTIVE: In the process of anterior cervical fusion, little is known about the biomechanics of anterior cervical screw pullout. In this study, three different aspects of cervical screw fixation were evaluated: self-tapping (ST) versus self-drilling (SD) screws, the effect of screw geometry (length, diameter, thread pitch), and the use of rescue screws. METHODS: Nine screws consisting of different diameters, lengths, and thread pitch (cancellous and cortical) were tested in peak pullout force in an artificial bone model using an MTS 858 Mini Bionix test system. Rescue screws (4.5 mm) were then inserted in the failed holes of 4.0-mm screws and extracted to determine their holding strength. RESULTS: Length of screws and thread pitch both had a significant effect on the pullout force. Each 1 mm of increased screw length translates to 16 N of increased force to pullout in the foam bone model. Pullout strength did not vary significantly according to screw diameter or between SD and ST screws. However, the SD screw has an advantage because it can decrease the length of surgery. A decrease in pullout force of between 43% and 70% was found when using rescue screws. CONCLUSIONS: In situations in which the use of rescue/salvage screws is required, the surgeon should anticipate a significant decrease in the holding force compared with the original screw. Future directions for research include an evaluation of pullout force for screw and plate constructs.
Authors: Heiko Koller; Frank Acosta; Mark Tauber; Michael Fox; Hudelmaier Martin; Rosmarie Forstner; Peter Augat; Rainer Penzkofer; Christian Pirich; H Kässmann; Herbert Resch; Wolfgang Hitzl Journal: Eur Spine J Date: 2008-01-26 Impact factor: 3.134
Authors: Murat Yilmaz; Kasim Zafer Yüksel; Seungwon Baek; Anna G U S Newcomb; Sedat Dalbayrak; Volker K H Sonntag; Neil R Crawford Journal: Clin Spine Surg Date: 2017-04 Impact factor: 1.876
Authors: Daniel Bronsnick; Ryan E Harold; Ari Youderian; Giovanni Solitro; Farid Amirouche; Benjamin Goldberg Journal: Clin Orthop Relat Res Date: 2014-10-02 Impact factor: 4.176
Authors: Heiko Koller; Axel Hempfing; Luis Ferraris; Oliver Maier; Wolfgang Hitzl; Peter Metz-Stavenhagen Journal: Eur Spine J Date: 2007-06-29 Impact factor: 3.134
Authors: Daniel Kyle Palmer; David Rios; Wyzscx Merfil Patacxil; Paul A Williams; Wayne K Cheng; Serkan İnceoğlu Journal: Int J Spine Surg Date: 2012-12-01