Literature DB >> 9019478

Effect of titanium surface roughness on chondrocyte proliferation, matrix production, and differentiation depends on the state of cell maturation.

Z Schwartz1, J Y Martin, D D Dean, J Simpson, D L Cochran, B D Boyan.   

Abstract

Although it is well accepted that implant success is dependent on various surface properties, little is known about the effect of surface roughness on cell metabolism or differentiation, or whether the effects vary with the maturational state of the cells interacting with the implant. In the current study, we examined the effect of titanium (Ti) surface roughness on chondrocyte proliferation, differentiation, and matrix synthesis using cells derived from known stages of endochondral development. Chondrocytes derived from the resting zone (RCs) and growth zone (GCs) of rat costochondral cartilage were cultured on Ti disks that were prepared as follows: HF-HNO3-treated and washed (PT); PT-treated and electropolished (EP); fine sand-blasted, HCl-H2SO4-etched, and washed (FA); coarse sand-blasted, HCl-H2SO4-etched, and washed (CA); or Ti plasma-sprayed (TPS). Based on surface analysis, the Ti surfaces were ranked from smoothest to roughest: EP, PT, FA, CA, and TPS. Cell proliferation was assessed by cell number and [3H]-thymidine incorporation, and RNA synthesis was assessed by [3H]-uridine incorporation. Differentiation was determined by alkaline phosphatase specific activity (AL-Pase). Matrix production was measured by [3H]-proline incorporation into collagenase-digestible (CDP) and noncollagenase-digestible (NCP) protein and by [35S]-sulfate incorporation into proteoglycan. GCs required two trypsinizations for complete removal from the culture disks; the number of cells released by the first trypsinization was generally decreased with increasing surface roughness while that released by the second trypsinization was increased. In RC cultures, cell number was similarly decreased on the rougher surfaces; only minimal numbers of RCs were released by a second trypsinization. [3H]-thymidine incorporation by RCs decreased with increasing surface roughness while that by GCs was increased. [3H]-Uridine incorporation by both GCs and RCs was greater on rough surfaces. Conversely, ALPase in the cell layer and isolated cells of both cell types was significantly decreased. GC CDP and NCP production was significantly decreased on rough surfaces while CDP production by RC cells was significantly decreased on smooth surfaces. [35S]-sulfate incorporation by RCs and GCs was decreased on all surfaces compared to tissue culture plastic. The results of this study indicate that surface roughness affects chondrocyte proliferation, differentiation, and matrix synthesis, and that this regulation is cell maturation dependent.

Entities:  

Mesh:

Substances:

Year:  1996        PMID: 9019478     DOI: 10.1002/(SICI)1097-4636(199602)30:2<145::AID-JBM3>3.0.CO;2-R

Source DB:  PubMed          Journal:  J Biomed Mater Res        ISSN: 0021-9304


  24 in total

1.  The early osseointegration of the laser-treated and acid-etched dental implants surface: an experimental study in rabbits.

Authors:  Mingdeng Rong; Lei Zhou; Zehong Gou; Andi Zhu; Dongfeng Zhou
Journal:  J Mater Sci Mater Med       Date:  2009-03-17       Impact factor: 3.896

2.  Scaffold structure and fabrication method affect proinflammatory milieu in three-dimensional-cultured chondrocytes.

Authors:  Heenam Kwon; Roshni S Rainbow; Lin Sun; Carrie K Hui; Dana M Cairns; Rucsanda C Preda; David L Kaplan; Li Zeng
Journal:  J Biomed Mater Res A       Date:  2014-05-03       Impact factor: 4.396

Review 3.  Implant surface characteristics and their effect on osseointegration.

Authors:  A Barfeie; J Wilson; J Rees
Journal:  Br Dent J       Date:  2015-03-13       Impact factor: 1.626

4.  Influence of acid-etching after grit-blasted on osseointegration of titanium dental implants: in vitro and in vivo studies.

Authors:  M Herrero-Climent; P Lázaro; J Vicente Rios; S Lluch; M Marqués; J Guillem-Martí; F J Gil
Journal:  J Mater Sci Mater Med       Date:  2013-04-27       Impact factor: 3.896

5.  Preparation and biological evaluation of hydroxyapatite-coated nickel-free high-nitrogen stainless steel.

Authors:  Makoto Sasaki; Motoki Inoue; Yasuyuki Katada; Yuuki Nishida; Akiyoshi Taniguchi; Sachiko Hiromoto; Tetsushi Taguchi
Journal:  Sci Technol Adv Mater       Date:  2012-12-13       Impact factor: 8.090

6.  In vitro generation of cartilage-carrier-constructs on hydroxylapatite ceramics with different surface structures.

Authors:  Katharina Wiegandt; Christiane Goepfert; Teresa Richter; Daniel Fritsch; Rolf Janßen; Ralf Pörtner
Journal:  Open Biomed Eng J       Date:  2008-12-30

7.  Development of a beta-type Ti-12Mo-5Ta alloy for biomedical applications: cytocompatibility and metallurgical aspects.

Authors:  D M Gordin; T Gloriant; G Texier; I Thibon; D Ansel; J L Duval; M D Nagel
Journal:  J Mater Sci Mater Med       Date:  2004-08       Impact factor: 3.896

8.  Surface characterization of implant materials c.p. Ti, Ti-6Al-7Nb and Ti-6Al-4V with different pretreatments.

Authors:  C Sittig; M Textor; N D Spencer; M Wieland; P H Vallotton
Journal:  J Mater Sci Mater Med       Date:  1999-01       Impact factor: 3.896

9.  Analysis of rat plasma proteins desorbed from gold and methyl- and hydroxyl-terminated alkane thiols on gold surfaces.

Authors:  M Källtorp; A Carlén; P Thomsen; J Olsson; P Tengvall
Journal:  J Mater Sci Mater Med       Date:  2000-03       Impact factor: 3.896

10.  Bone response to surface modified titanium implants - studies on the tissue response after 1 year to machined and electropolished implants with different oxide thicknesses.

Authors:  C Larsson; L Emanuelsson; P Thomsen; L E Ericson; B O Aronsson; B Kasemo; J Lausmaa
Journal:  J Mater Sci Mater Med       Date:  1997-12       Impact factor: 3.896

View more

北京卡尤迪生物科技股份有限公司 © 2022-2023.