Pyrolysis: An effective technique for degradation of COVID-19 medical wastes.

COVID-19 has led to the enormous rise of medical wastes throughout the world, and these have mainly been generated from hospitals, clinics, and other healthcare establishments. This creates an additional challenge in medical waste management, particularly in developing countries. Improper managing of medical waste may have serious public health issues and a significant impact on the environment. There are currently three disinfection technologies, namely incineration, chemical and physical processes, that are available to treat COVID-19 medical waste (CMW). This study focuses on thermochemical process, particularly pyrolysis process to treat the medical waste. Pyrolysis is a process that utilizes the thermal instability of organic components in medical waste to convert them into valuable products. Besides, the technique is environmentally friendly, more efficient and cost-effective, requires less landfill capacity, and causes lower pollution. The current pandemic situation generates a large amount of plastic medical wastes, which mainly consists of polyethylene, polypropylene, polystyrene, polyethylene terephthalate, and nylon. These plastic wastes can be converted into valuable energy products like oil, gas and char through pyrolysis process. This review provides detailed information about CMW handling, treatment, valuable product generation, and proper discharge into the open environment.

Introduction

In December 2019, there has been an outbreak of the novel coronavirus disease-2019 (COVID-19) in Wuhan, China. Later, in March 2020, the World Health Organization (WHO) announced the prevailing conditions to be a pandemic since spreading the viral infection was enormous and affecting most of the world countries populations. It wiped out millions of people worldwide and left behind more than 100 million people (Exact numbers - 100,455,529 million confirmed cases of COVID-19 as of date January 29, 2021) infected by the deadly virus (WHO, 2020a). This contagious disease is caused by novel β type severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), which has more similarities to SARS-CoV (2002) and MERS-CoV (2012) virus outbreaks. A hypothesis suggests that SARS-CoV-2 might have transmitted from bats to humans. The rapid spreading among humans occurred mainly via droplets, contacts and airborne transmissions. This pandemic situation has shaken the whole world’s economy drastically and most people remained jobless or surviving with struggled businesses (WHO, 2020b).

COVID-19 has created sudden panic and chaos among the public as well as the government sectors of the world nations. Numerous countermeasures are undertaken to identify (using PCR and rapid test), control (nationwide lockdowns, social distancing, using personal protective equipment [facemask, face shield, gloves, etc.], and quarantine of patients or suspects), and prevent the fatal pandemic (trials on various anti-viral drugs or vaccines and life-support treatments) (Das et al., 2020; Singh et al., 2020). Adopting these processes has led to the increase of the huge amount of COVID-19 wastes [CW] like Medical Waste [MW] (mostly generated from hospitals, clinics and healthcare centers), Bio-Medical waste [BMW] (generated during medical diagnosis, treatment, or immunization of disease, and biological research activities on animals) and Common Packaging Plastic Waste [CPPW] (closure of cafeterias and restaurants has led to home delivery services of food and groceries) (Aggarwal, 2020; Sharma et al., 2020). Covid-19 pandemic increases extensive use of plastic materials and creates environmental issues (Sharma et al., 2020), and it has been clearly addressed in Fig. 1 .

Fig. 1

Various types of plastic wastes generated from the packaging, medical and other plastic waste sources.

During COVID-19, a huge amount of CW has been generated and it is about three to six times more than the regular municipal solid waste (MSW). CW is sourced mainly from hospitals, clinics, and healthcare centers. Apart from hospitals, treatments undertaken from home quarantine and wastes generated from these are also classified under CW. Medical waste (MW) discharged from hospitals or health care centers carries some trace of infectious agents and are therefore termed as hazardous waste (HW). These MW or HW needs special attention or care for the wastes safe disposal and may cause reinfection to human society if not treated appropriately. Biomedical waste (BMW) is another classified CW that is mostly generated from medical institutions and research laboratories. These are the places where the drug or vaccine trial phases are undertaken to diagnose and treat (WHO, 2018). The quantum of BMW generated will be excessive from these sites as they are composed of 85% non-hazardous waste and 15% hazardous waste (10% biological waste and 5% chemical or radioactive waste) (Datta et al., 2018). COVID-19 has posed the sudden emergence of another type of CW due to the lockdown and shutting down of hotels and cafeterias. This situation has created a huge demand for home delivery of food and groceries among the public, which has generated large amounts of common packaging plastic waste (CPPW). CPPW also must be considered as hazardous waste (HW) since the handlers may be symptomatic or asymptomatic and may carry traces of the virus (Neel, 2020). It has been observed that viruses can exist on plastics, metals, glass, paper and cardboard for more than a few hours to a few days. The pathogens carried either by MW or BMW or CPPW (altogether considered as HW) without appropriate treatments would properly expose the public again to the danger of SARS-CoV-2 infection (van Doremalen et al., 2020; Kampf et al., 2020).

The worldwide prevalence of the treatment and disposal of medical waste (MW) during the COVID-19 pandemic is not fully addressed. Most countries faced the sudden increase of MW from hospitals or healthcare centers, that have not been provided enough handling time or space to deal with the infrastructure development to contain as well as properly disposing of the CW. The pandemic has totally changed the waste management systems as well as the workers involved in the cleanliness. CMW carries around 20% hazardous waste, which contains infectious agents, toxic chemicals, and radioactive substances. Therefore, it needs effective waste management and treatment that can help in disease containment and in safeguarding the environment (WHO, 2015; WHO, 2017; WHO, 2020c). CMW has to be separately handled; otherwise, it may get mixed with regular municipal waste, contaminating with infectious agents. Certain steps have to be followed for proper handling of CMW from the origin to the disposal sites, which includes 1) classification or segregation of CMW, 2) collection in separate bags or bins, 3) proper disinfection for the temporary storage area and the transport vehicles carrying CW, and 4) high-temperature disinfection treatments and disposal facilities. Healthcare workers have to be given adequate training for effective management of these CW. Each government needs to effectively undertake waste management treatment of these CW so that any infection can be avoided entirely (Sharma et al., 2020).

Standard disinfection technologies used to treat COVID-19 Medical Waste (CMW) include the incineration, physical and chemical methods. These disinfection technologies are applied at various stages in the Waste Management Systems (WMS) to handle different types of waste that are carried by CW (Ilyas et al., 2020). Incineration at high temperatures can be the superior or efficient technology that can be adapted to handle the CW, and it would be sufficient investment for disinfecting pathological and pharmaceutical CW. Chemical disinfection combined with other technologies like microwave or steam disinfection techniques at the latter stages can be followed by the small investment hospitals for clearing the CW. Though incineration technology would efficiently degrade SARS-CoV-2 viruses at high temperatures, it still carries certain disadvantages like the release of toxins into the environment and drastically affects humans and animals’ immune system (Ghodrat et al., 2017; Wang et al., 2020). So, there is an immediate need for alternative technology for the CMW treatment. Thermal technology was one of the techniques that assist competently in degrading CW, and they are sub-classified into two types: 1) pyrolysis (operates at high temperatures) and 2) microwave (operates at medium range temperatures).

Pyrolysis, one of the thermochemical processes wherein the organic compounds (solid and liquid waste) present in CMW are disintegrated at high temperatures under anaerobic or low-oxygen conditions. The macromolecular compounds present in CMW are thus broken down into simpler compounds like solid or liquid fuels, crude synthetic gases, and carbonaceous materials (coke, char). The solid or liquid products so formed have high commercial value and also can act as an alternative energy substitute for the existing fossil fuels, which are nowadays getting depleted (Singh and Ruj, 2016; Zaman et al., 2017; Basu, 2018).

Apart from other MW, a significant waste that is formed during the COVID-19 pandemic is the generation of huge amounts of plastic waste (PW). These include surgical drapes, disposable gowns, disposable syringes, personal protective equipment (facemasks and shields), disposable gloves, and testing kits. These components are made from plastic materials like polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET) and nylon (N). These plastic wastes (PW) generated during COVID-19 upon pyrolysis treatments can provide valuable energy-producing products like liquid oil, gases (syngas, hydrogen gas), hydrocarbons and char (Tenenbaum, 2020). The liquid oil so formed as one of the byproducts has a high heating value, which possesses characteristics very similar to any commercial fossil fuel (Kaufman and Chasan, 2020).

This study highlights the current COVID-19 crisis in handling, treatments and discharge of CMW. Further, it also tries to provide effective solutions for the existing challenges that are conquered during the COVID-19 conditions, specifically on the waste management processes. Notably, much emphasis has been placed on pyrolysis’s eco-friendly approach, which would be an effective treatment method for converting CMW into valuable energy products. The whole COVID-19 waste management approaches and their future prospects are shown in Fig. 2 .

Fig. 2

COVID-19 waste management approaches and future prospects.

Medical waste generation during COVID-19

During the COVID-19 outbreak, large amounts of medical wastes (mostly facemasks, gloves, gowns, syringes, sharps, etc.) are generated from hospitals. They have mainly been classified as hazardous components for carrying infectious agents (WHO, 2020d). Inappropriate handling of these would lead to the contamination of the virus with the common municipal waste and also the high possibility of its transmission (CDC, 2020; PHAC, 2020; WHO, 2020e; ECDC, 2020). Effective management of medical waste that was raised during COVID-19 can be brought about by adopting specific measures like accurate identification, collection, segregation, storage, transportation, treatments and final disposal (Ilyas et al., 2020). Around the world, all government sectors have been instructed to treat hazardous medical waste as an urgent and important public priority that would reduce its secondary effects on the health of individuals and the environment.

Hospitals or healthcare centers alone cannot be the source of infectious waste; even the people with slight symptoms or the asymptomatic persons can also create the virus-laden waste (mostly sourced from their discarded facemasks, gloves, and used tissue paper). Since it has been estimated that the virus can survive in plastics for 6–8 h, stainless steel for 5–6 h, and in contaminated PPE, it may last up to 7 days; just dumping such wastes would infect the sanitary workers involved in the waste management (Chin et al., 2020). The situation is still worse in the developing countries for the handlers engaged in COVID-19 waste management because they are not properly equipped with PPE. Other people who are more prone to get infected from virus-laden waste in developing countries would be the rag and casual waste collectors. The crucial steps that have to be followed to overcome the pandemic situation will be the appropriate treatment facility and safe disposal of CMW, which would control as well as prevent the spreading (Cutler, 2020).

Waste generated from medical institutions and their related research centers would be considered as Bio-medical waste (BMW) as defined precisely by WHO. The medicinal practice that is being undertaken in such places includes diagnosis, prevention, healing, and caring treatments in the area of human and animal medicines. Even the waste generated by an individual’s healthcare activities at their residence is also grouped under BMW. BMW comprises medicinal, chemical, pathological, infectious, metallic (sharps), and radioactive substances (Sharma et al., 2020). Inappropriate disposal of BMW in the roadsides of cities or towns as well as in the empty lands of the suburban may lead to groundwater contamination, affecting their soil enrichment, causing injuries, radioactive leakage and killing the beneficial microorganisms (Pandey et al., 2016). During the COVID-19 pandemic time, there has been an enormous rise in the quantum of BMW; this may be because of the high consumption of disposable items either for the treatments or for the development of vaccine productions (Klemeš et al., 2020). Recent reports suggested that the primary source of infections was through accidental contact of items disposed of either by workers or by the patients at the time of its generation. In some developed countries, hospitals and healthcare centers are lawfully bound to properly dispose of such wastes, vastly preventing the BMW’s mismanagement. The spreading or getting infected easily is mainly due to the BMW’s careless handling and the inadequate maintenance of hospitals or healthcare centers (WHO, 2005; WHO, 2015). Earlier experiences of pandemic outbreaks have provided enough knowledge on biomedical waste management systems to effectively control and prevent diseases (Datta et al., 2018; Anthru, 2020).

In some developing countries, the municipal solid waste gets mixed by the hazardous CW during pandemic situations due to a lack of basic amenities like sealed plastic bags or safety bins to collect separately. Third-party companies will abuse the provision of massive incentives and inadequate waste monitoring systems, leading to unregulated and cheap treatment or even illegal dumping (WHO, 2015; Hopman et al., 2020). Instances of reselling disposables on black markets for re-uses such as gloves, masks, sharps and other infectious waste can lead to disease outbreaks (WHO, 2017). Due to a lack of implementation of laws, such mishaps may be more common in developing countries. Another topic of concern is the failure of current healthcare center on-site treatment facilities to resolve the variance in BMW generation. Many of these facilities are fitted with steam sterilization (autoclaving) infrastructure, energy-based treatment (microwave, radio-wave), incineration, chemical disinfection, etc., for BMW, as defined by the regulatory body. However, because of the increased costs experienced, failure to comply with strictly controlled emission has become a significant restriction on these facilities’ usage (Resilient Environmental Solutions, 2020). The change to a consolidated waste management system may also result in greater compliance with emissions standards. In designing these systems, there should also be a provision to cope with enormous waste generation fluxes during COVID-like disasters. Several other problems should also be tackled to avoid more infections, such as emissions of aerosol microbial pollutants from the grinding/shredding of waste, etc. Integrating urban local authorities and assigning unique roles can be the key to ensuring enforcement during pandemics for efficient BMW management by hospital management and its personnel (Rowan and Laffey, 2020).

Plastics have become an important part of day-to-day life, particularly during the COVID-19 pandemic period. Lockdown was implemented that included the shutdown of restaurants and cafeterias, closure of markets places worldwide to impose social distancing among the people so that the spreading of the virus can be controlled. But this situation has directed the public to go for home delivery services of food, groceries and other essential commodities (even medicines), which has led to a huge rise in plastic packaging waste. The main components of packaging plastic waste include polypropylene, polyethylene, polyethylene terephthalate, and polystyrene (Table 1 ). Due to the outbreak of COVID-19, some places have caused recycling operations to be temporarily stopped, which has caused an enormous amount of plastic packaging waste, including CW that gets accumulated in garbage collecting bins, dumping sites, and even sometimes on roadsides (WHO, 2020f). Pharmaceutical industries that aim to supply medical commodities worldwide and their high demand during COVID-19 have also caused increased plastic packaging waste. Many countries exhibited a sudden increase in online shopping during the COVID-19 pandemic due to high safety and hygiene concerns. The packing plastic usage was mostly confined to food and groceries and these were either in the form of thin films, Styrofoam, or thick plastic materials. The main concerns for an environmentalist now are about the recyclability of these huge piles of packing plastics emerging during the COVID-19 pandemic (Hyun, 2020; Jribi et al., 2020).

Table 1

List of some common materials of COVID-19 Medical Waste (CMW) and their associated plastic wastes.

S.No.	Disposable sources	Common materials of COVID-19 Medical Waste	Types of Plastic waste
1	Hospitals, Medical Clinics, Health-care centers, Research and Development sectors, Home Quarantine, Household,	COVID test kits, Masks, respirators, syringes, feeding tubes, oxygen pipes, suction probes, saline bottles, catheters, gloves, aprons, Shoe masks, face masks, caps, covers, goggles∖glasses, clothing, and packaging bags,	PET (polyethylene terephthalate), HDEP (High density polyethylene), LDEP (low density polyethylene), PVC (poly vinyl chloride), PP (Polypropylene) and PS (polystyrene).

In some countries, the public’s implementation of single-use plastic bags was forced due to health concerns during the COVID-19 crisis. Often the usage of single-use plastic bags is beneficial, but it generates lots of waste and this adds up challenges to the already stressed waste management system prevailing in any country. This temporary usage of single-use plastic bags would change consumers’ behavioral patterns, preferring to use them as a guard against contamination. Reusable or recyclable plastics will lose their validation if the situation continued, and subsequently, single-use plastic bags will increase in daily consumption and will get retained in average circulation even after the pandemic (Sharma et al., 2020).

It has been estimated that during the COVID-19 outbreak, the amount of plastic waste has increased considerably, accounting for nearly 44.8% from packaging and 13.2% from others (medical). This rise is mainly due to online shopping as well as certain consumables like hand sanitizer, disinfectant spray, cleaning agents, disposable wipes, facemask, gloves, etc. It all reflects that the production of plastics for packaging and other purposes has got increased. Even the governments have increased their output due to the demand (WHO, 2020g). Meanwhile, most of the packing material, as well as the medical accessories (facemask, gloves, shield, gowns, syringe), are made from plastics, which is in wide demand during the pandemic situation. The plastics consumption will further increase and the condition will worsen upon online ordering of food and groceries. The COVID-19 pandemic will pose a significant danger to the environment as enormous amounts of plastics are used, which will create major health problems for humans and animals (Sharma et al., 2020).

Naturally, there are four ways to degrade plastics from the environment – photodegradation, thermo-oxidative degradation, hydrolytic degradation, and biodegradation using microorganisms. In which some process like photodegradation followed by thermo-oxidation may lead to the breaking of the plastic materials. Later the carbon in the polymer on microbial action is changed to carbon dioxide or utilized for biomolecule synthesis, but it takes many years to proceed. So, recycling of plastics would be the best solution to be adopted (Grigore, 2017).

There are four ways of the recycling process of plastics or plastic waste, which include 1) primary recycling, 2) mechanical recycling, 3) chemical recycling, and 4) energy recovery (Francis, 2016). In the primary recycling process, the reuse or recycle of the native products as such but it carries certain demerits like limited recycles for that recycled products though they are cost-effective. Mechanical recycling is otherwise called secondary recycling in which thermoplastics are remelted and processed to their respective end products. It is the physical method in which the plastic waste polymers are either shredded or granulated or made into pellets and melted to regenerate new products. Sometimes they are mixed with virgin plastics to look like new ones. The major demerits in these products’ usage include their heterogenicity and quick declining properties in each recycle. Comparatively, this process is less expensive, but it needs considerable investment initially. In the chemical recycling process, the plastic waste polymers are transformed into monomers or oligomers upon chemical reactions. Still, the process is in an experimental state because of large investments as well as expert’s opinions on their optimization. Extensive studies are currently carried out in the gasification and pyrolysis process of chemical recycling (Sharma et al., 2020). In the pyrolysis process, the polymeric plastic waste is degraded during high-temperature heating without oxygen. The process clearly exhibits the release of liquid oil and gas fractions, which can be reutilized as feedstock to manufacture new plastics. Quaternary recycling refers to the complete recovery of energy from plastic waste polymers through the process of incineration. Though the technique helps to generate considerable energy from the plastic waste, some airborne toxic substances like dioxins are released into the atmosphere, leading to the environmental pollution, which is of great concern nowadays (Wang et al., 2020).

The COVID-19 medical waste such as masks, gloves, aprons and other materials, which are mostly made from plastics, are not recyclable currently because it may carry a trace of infectious residues (International Solid Waste Association (ISWA), 2020). This may greatly affect the professional workers during the handling or collection of those waste and at the waste treatment facilities. For workers’ safety, certain rules are lifted in current situations like regular change and cleaning PPE, gloves and professional dresses, and frequent handwashing. In many underdeveloped or developing countries, recycling sector workers are at risk conditions.

The thermal treatment of CMW is much safer when compared with other techniques. One would be the complete destruction of the pathogenic agents and its meltdown, which may lead to excellent energy recovery from the plastic waste polymers. Generally, reusable facemask, which are mostly made of polypropylene, has several layers and they are recyclable using the thermochemical process or mechanical recycling. It has to be assured that complete destruction of residual pathogens carried by the hospital waste and healthcare centers because if they are not properly disposed of, it may lead to contamination and can be a source of infections (Nzediegwu and Chang, 2020).

Recycling of waste during the COVID-19 outbreak is a huge challenge because most recycling facilities are shut down because the authorities might be at the risk of spreading the infections in their respective recycle centers and in some countries, complete restriction of their waste management system. Arise of the COVID-19 has led to food package deliveries due to isolation and this facility utilization has increased significantly. A recent survey states that pharmaceutical and medical products, as well as food packages, are produced enormously. Though many regulations during the COVID-19 pandemic implemented but still the continuity of recycling of the waste is one of the essentials, if not whole waste management system will be got saddled with piling up of the waste materials and it would be a risk of whole recycling system failure (Plastics Today, 2020).

: Landfilling is considered an efficient way of disposal of the plastic waste management system, particularly in developing countries. Even some of the developed cities have high-tech scientific landfills, unsanitary landfills, or dumping yards for the waste. Landfilling is considered exclusively for waste management rather; incineration is applied for energy recovery from the plastic waste. It has been identified that less carbon dioxide emission resulted in landfilling of the plastic waste when compared with the incineration process (Sharma et al., 2020). But still in some developing or underdeveloped countries follow unsanitary dumping of waste, which leads to vast space occupying, leaching of hazardous chemicals, sometimes results in open fire in dumped area, which leads to release of harmful gases like dioxins and furans. The huge piling of waste during COVID-19 pandemic vastly disrupted the recycling capacities and the incineration process. So, the resulted waste was either dumped or landfilled to get degraded naturally as well as its pathogenic capacities are neutralized. Furthermore, the improper waste management during the pandemic time may lead to complete mishandling of the COVID-19 plastic waste, and so serious environmental issues in the upcoming years. The World Health Organization has recommended that underdeveloped might not advance waste management system for handling the biomedical wastes, which may go on burying the collected waste in a close pit of 2 × 3 m with clay or geo-synthetic coating at the bottom, and this can be practiced only during emergencies conditions for safe disposal of biomedical waste. Once the waste got disposed of in the pit daily, it has to be filled with fresh soil or lime mix. The areas surrounding the pit should be wire fenced to get outreach of animals as well as humans (Vanapalli et al., 2021).

Challenges in COVID-19 waste management

COVID-19 has enormously affected the world, infecting millions of people and leaving numerous dead. The world has been facing unexpected disasters now, and each government aims to protect the people’s lives. It has been a great challenge for the government to handle the pandemic situation with the prevailing infrastructure facilities and inadequate safety equipment. The accomplishment of multiple testing centers, sudden changes and improvisation in medical standards, and public policy alterations have been adopted to face the current public health crises (UNEP, 2020).

Imparting complete lockdown, social distancing among individuals in public places, self-quarantine for the infected person, and compulsory use of personal protective equipment were implemented from government sectors to control the spreading of SARS-CoV 2 virus. Consequently, this situation has totally altered the waste generation and management patterns. Before COVID-19, the solid waste generated was handled by sanitary workers and then transported to waste management centers. However, after COVID-19, the wastes that have been discharged are considered hazardous in nature, which might carry infectious agents, and it needs separate handling, treatment and disposal facilities (Mallapur, 2020). If CW is not appropriately disposed of, it may get mixed up with the municipal wastes and could pose the risk of transmission among the sanitary handlers as well as the public. Therefore, a separate waste management system was the immediate requirement for the safe handling of CW. It needs specific disinfection technology or treatments to destroy the infectious agents that are carried along with the wastes (UNEP, 2020). An accurate cyclic system has to be followed while handling CW. The government has advised the sanitary workers during COVID-19 time to collect the medical household and other hazardous waste safely, which are later taken to waste treatment facility centers. This can minimize the further impacts of the infectious agents carried by CW on public health and the environment (Sharma et al., 2020).

The COVID-19 pandemic has greatly affected the farmers and food suppliers due to the sudden implementation of nationwide lockdown and complete halt of all transportation modes. These conditions created a chaotic situation among the people, which forced them to stock the essential needs like foods, groceries, and some necessary medicines. This has led to disordered supply as well as the shortage of these items among the communities. Excessive stocking of essential goods with less shelf-life has caused many such products to be compulsorily thrown or dumped in nearby waste bins or on the roadsides. Thus, the COVID-19 crisis has caused a sudden demand in food chain supplies and associated challenges in solid waste management (Bellany, 2020). The situation has also totally changed the dynamics in the generation of medical, plastic, and food wastes. So, it requires specific and compelling waste management systems to handle the pandemic situation, and also it needs innovative solutions to efficiently tackle the present and future pandemics (Neel, 2020; Sharma et al., 2020).

The sudden appearance of COVID-19 and the spread among people have led to the tremendous use of some essential accessories, such as facemasks, gloves, hand sanitizers, disinfectant sprays, to reduce virus transmission (Barcelo, 2020). Hospitals or health centers alone should not be regarded as the sources of infectious waste, but the carriers of the viruses can also be asymptomatic people or those with moderate symptoms and masks, gloves, tissues discarded by them. Moreover, the virus can survive for extended periods of time, sometimes up to days in plastics, metals and cardboard. Dumping of these items will affect sanitary workers who are involved in the collection of these wastes. In some underdeveloped or developing countries, the condition will still be worse for the sanitary works because either they are not properly equipped or not wearing any type of PPE while handling CW. It has become difficult even for the waste treatment facility centers to handle the unusual quantum of waste generated during the COVID-19 pandemic (Singh et al., 2020). In developing countries, the management of CW has been a great challenge from the collection, transportation, treatment and disposal without being affected. These countries have limitations like lack of technology as well as scientific knowledge and poor economic background (Bourouiba, 2020). The above-mentioned challenging factors that have arisen during the pandemic time have led the countries to focus and provide special attention to waste management systems and their treatment facilities for CW (WasteAdvantage, 2020).

Strategy in segregation and pre-treatment of CMW

It has been estimated that hospitals, clinics, and healthcare centers were the major sources of CMW. They generate different types of CW, which include diagnostics, drugs, other medicinal waste, research and laboratory waste, infectious waste, cytotoxic waste, chemical and radioactive wastes. Most of these CW carry hazardous materials that could cause serious risk to the public and the environment if the wastes are not properly handled or disposed of. The first step to manage CW has to start from the hospitals where it gets originates. The hospital wastes have to get properly classified and collected in separate bags or bins designated for that purpose. The CW containing bags has to be disinfected and sealed in double-layered plastic bags before it is transported to the facility centers. The segregated CW bags are temporarily kept in the storage area where the wastes are collected on a priority basis or within the deadlines. The Temporary storage area and transporting vehicles of CW have to be in regular disinfection conditions to avoid the chances of infection to the handling workers before it gets carried to the common COVID-19 waste treatment and disposal facility centers (CCWTDF) (Sing et al., 2020b). Appropriate disinfection technology has to be selected or adopted based on the quantity, types, cost and maintenance for treating CW. For large-scale treatments of CW or CMW, either incineration or pyrolysis, methods can be adopted since both operate at higher temperatures (540 °C–830 °C), which can completely destroy the infectious agents carried by them. The rest of the residual compounds or gases that remain after the combustion process can be utilized for energy conversion products. Some hospitals or healthcare centers have a smaller scale disinfection system for handling CW, where these are primarily treated with chemical disinfectant and then passed on for a microwave combined with steam disinfection technology (operates at temperature 93–540 °C) (Wang et al., 2020).

Pyrolysis: an effective technique for decomposing the COVID-19 waste

Disinfection technology (DT) would be the primary step that can be adopted for safe handling and treating of CW. Since most of CW are sourced from hospitals as CMW, they can undergo preliminary disinfection treatments in the temporary storage place in the healthcare centers before it gets discharged and transported to the large-scale waste treatment facility (Barcelo, 2020). Generally, DT has been classified into three types: incineration, chemical and physical disinfection (Fig. 3 ). Based on the amount of waste, these DT can be adopted at various scales. Incineration technology (IT) is mainly adopted for large-scale investments as well as the treatment of a huge amount of wastes. Particularly, incineration technology would help to treat large amounts of hospital wastes discharged during the COVID-19 pandemic and get effectively disinfected from infectious or pharmaceutical wastes. Chemical and steam disinfection treatments are mainly adopted for smaller investments such as in hospitals or healthcare centers themselves for storing or temporary treatment of CW, which can minimize the transmission of infections or pathogens among the handlers of the wastes (ACR Plus, 2020).

Fig. 3

COVID-19 waste generation and disinfection treatments.

The IT process operates at high temperatures ranging from 800 °C to 1200 °C and its combustion can completely destroy the infectious agents carried by CW. Nearly 90% of organic components present in CW are burned and converted into residual inorganic dust (Ghodrat et al., 2017). During IT process, there have been major releases of toxins like products of incomplete combustion (PIC) and dioxins. PICs are formed when the waste gets disintegrated during the incineration process and gets reorganized into small particles later on by post-combustion cooling. Dioxins are released on burning CMW since most components are of plastic wastes. The metals which are carried by CW upon combustion are dispersed inside the chamber and can act as catalysts for the formation of dioxins. Furans coexist along with other toxins, which are released during the IT process. The toxins released during the IT process can store in fatty cells and run along the food chain (Chen et al., 2015). They are carcinogenic substances that can harm the immune system as well as causing an imbalance in hormonal secretions. The final ash product so formed during the completion of IT process has to be analyzed for any toxic substances before being buried in landfills. To control toxins emission from the incineration reactors, additional flue-gas treatment facilities have to be attached, which can be an extra cost for the facilitators or users (Makarichi et al., 2018). Apparently, operating the IT with a smaller amount of waste will not be practically feasible and require alternative eco-friendly methods for the safe and effective treatment of CMW.

Rotary kiln incinerator

This type of incinerator is widely used in China for treating their CW or PW. The equipment consists of a rotating oven and a post-combustion chamber. Rotary kiln not only helps in the mixing of wastes thoroughly but also exhibits efficient incineration. The kiln is loaded with the wastes on the top and rotates 2 to 5 times per minute (Ma et al., 2011). The incineration temperature could be as high as 1200–1600 °C, which could efficiently destroy the hazardous materials that are carried by COVID-19 waste. The gases evolved in the kiln are forced to pass through the combustion chamber, where the organic compounds are burned with the residence time of 2 s. The ash remains are collected at the bottom. The incineration capacities that are available ranges from 0.5 to 3 tonnes/hour. Those designated as toxic or hazardous wastes like CW has to be operated separately and to be located in an isolated environment. It is an adequate technology for handling infectious wastes, cytotoxic wastes, chemical and pharmaceutical wastes but not adequate for radioactive wastes (treatment does not affect its properties and may get dispersed its radiations), pressurized containers (gets exploded during the process and may cause damage to the incinerator) and high heavy metal content wastes (emission of toxic heavy metals into the atmosphere on incineration process). The exhaust gases and ashes are produced upon incineration of CW, which may still carry some toxic substances and has to be treated again. Generally, the equipment and operation costs are high due to its excess energy consumption, and the by-products so formed are highly corrosive, which causes the kiln to get often repaired or replaced (Dorn et al., 2012; Chen and Yang, 2016).

Plasma incineration

This is one of the efficient technologies that can be used for the effective treatment of CMW. In this process, electric power is used for plasma generation and more than 2700 °C of temperature is produced. This makes a large amount of waste to get quickly decomposed into smaller molecules. It doesn’t form any intermediate product, and the gases so formed are purified and discharged into the atmosphere. Compared to other techniques, plasma incineration technology exhibited more efficiency because of higher energy production and less volume of ash generated (Sapuric et al., 2016; Messerle et al., 2018).

Alternative disinfection technology that can be adopted for the treatment of CMW would be high-heat pyrolysis, plasma pyrolysis, medium-heat microwave, and low-heat autoclave techniques.

High-heat pyrolysis technique

Compared to incineration, pyrolysis would be a better technique. High-heat pyrolysis techniques will be fully functional at a range of temperatures from 540 °C to 8300 °C. Different types of high-temperature pyrolysis techniques do exist, which include pyrolysis-oxidation, induction-based pyrolysis, laser-based pyrolysis, and plasma pyrolysis. In pyrolysis oxidation, a uniform high temperature (approximately around 600 °C) is supplied to the primary combustion chamber. The organic wastes (solid or liquid) get vapourised and leave behind residual ashes, metals and glass pieces. Further, the vapourised gases (that contains mostly toxins) are passed through the secondary combustion chamber where the temperature remains in the range of 982–1093 °C, which helps in the complete destruction of the harmful substances (Dai et al., 2014).

Plasma pyrolysis

It is one of the advanced technologies that utilizes electric current to generate high heat of maximum up to 9730 °C, leading to the formation of electric arcs or plasma torch. The plasma state is obtained when electricity is supplied, wherein both organic and inorganic substances present in CMW are converted into the gaseous ionic state and start conducting electricity due to high resistance, which leads to the liberation of high heat energy. Even heating at 1300–1730 °C results in the destruction of infectious agents carried by CW. At 2730 °C, highly resistant cytotoxic drugs are broken into simple substances (Cai and Du, 2020), whereas CW’s inorganic waste gets converted to neutral slag and metal remains. During the plasma pyrolysis, there is a significant reduction of atmospheric toxin emission like dioxins, furans and pyrene compounds. Most of the resulting gases liberated from this process are highly inert and non-toxic in nature. There is much reduction in residual ash and slag formation when compared with the incineration treatment of wastes. The high heat generation in the plasma technique can destroy CW or CMW or CPPW safely and reliably. Many types of wastes like plastics, metals, infectious waste, pharmaceutical waste, low radiation waste are completely destroyed using the plasma pyrolysis. This technique’s advantages include the low emission of gases, inert and sterile residual compounds, environment-friendly and volume reduction of up to 95%. The disadvantages of the plasma pyrolysis technique include the high investment cost, high operation cost, excess electrical usage, partial lifespan of the plasma torch and occasional evolution of dioxins in poorly setup plant (Chang-Ming et al., 2016).

Medium heat microwave technique

In this technique, the CW is operated between temperatures ranging from 177 °C to 540 °C and involves the application of high energy microwaves under the inert environment of nitrogen to destroy the various components present in the CMW. The process consists of the absorption of microwaves by the CW, which ultimately increases the internal energy resulted from the vibration and rubbing of molecules. Nitrogen not only provides an inert atmosphere but also avoids the combustion with oxygen, which can result in high-temperature disinfection. The advantages of using microwave techniques include low energy consumption, high-temperature attainment, partial heat loss and eco-friendly with no toxic emission. Microwave technology can be applied as mobile or on-site disinfection technology for treating the CW and that can avoid the risk of CW transportation. The microwave technique, combined with autoclave, can be effective in technological methods that can be applied for treating the CW. Hospital infectious waste like gauze, bandages, gowns, sharps can be sterilized using microwave technology. Organic compounds (volatile or semi-volatile), heavy metals (Mercury) and radioactive wastes cannot be treated using microwave technology (Wang et al., 2020).

Low heat autoclave technique

This technique is functional in temperatures between 93 °C and 177 °C and mostly, they include autoclaves. Autoclave operates using steam as sterilizing agents. To make the autoclaved waste to be reduced in volume, they are either ground or shredded. The air inside the autoclave has to be disinfected before released into the environment by allowing it to pass through a high-efficiency particulate absolute (HEPA) filter, which traps the pathogens. Most of the CW can be sterilized using the autoclave technique, but hazardous and chemical waste cannot be done, as they release toxic substances. Even the heat-resistant containers, beddings from hospitals and other bulky waste cannot be disinfected using the autoclave technique (Zhang et al., 2016).

Conversion of CMW into sustainable energy

Pyrolysis is one of the techniques that have been used for the treatment of municipal solid waste consisting of household, small industrial and some common hospital wastes. These include components like papers, plastics, metal particles, textile clothes, organic wastes, leather contents, rubber, glasses, ceramics and other materials. It is defined as the process wherein the components undergo thermochemical decomposition at a higher temperature under anaerobic or low oxygen conditions. In recent days, the process is getting much attention because of its flexibility in generating the mixed proportion of solid, liquid and gaseous products (Zhou et al., 2014; Anuar Sharuddin et al., 2016). It only requires variation in operating parameters like different temperatures or heating rates. Pyrolysis technology also has the capability of transforming low-energy-density materials into high-energy fuels. Nowadays, different types of pyrolysis techniques have been developed and each operates with specific types of reactors that are designed to treat a precise amount of wastes to generate definite products (Chowdhury and Sarkar, 2012; Biswal et al., 2013; Grycova et al., 2016; Czajczyńska et al., 2017). Different types of reactors used in the pyrolysis process and their advantages and disadvantages for the treatment of CW are shown in Table 2 .

Table 2

Different types of reactors used in pyrolysis process for the treatment of CW.

S. No.	Types of reactors	Functions	Advantages	Disadvantages	References
1	Fixed bed reactor	The feedstock is mounted in the stainless-steel reactor, which is externally heated by an electric furnace. It is flushed by inert gas such as nitrogen or argon until the reactor becomes useable and this gas flow is retained throughout the entire process to provide an anaerobic atmosphere. During pyrolysis, the obtained gases and vapours are discharged from the reactor, but char is normally extracted after the process. Low heating rate is defined for the fixed bed reactor.	1. Best suited for laboratory-scale.2. Simplicity in design3. Consistent in their outcomes.	1. Feedstock does not shift in the reactor, which makes it impossible on an industrial scale to uniformly heat a significant portion of MSW.2. It’s really challenging to remove char.3. High conservation of carbon.4. Long solid residence time.	Jouhara et al. (2017); Czajczyńska et al. (2017)
2	Fluidized bed reactor	The reactor consists of a two-phase mixture, solid and liquid, which is normally done by moving a pressurized fluid through the solid material. A high heating rate and a strong mixing of the feedstock defines these reactors. A successful solution for waste polymer pyrolysis tends to be this sort of reactor.	1. They are more appropriate for studying the behaviour of fast pyrolysis solid particles.2. Analysis of secondary oil cracking at longer residence times.3. In laboratory studies, these reactors are generally used to explain the effect of temperature and residence time on pyrolysis behaviour and products.	1. There are issues with the use of fluidized-bed reactors for MSW handling.2. The raw material delivered to the reactor must be thin, so that it can float in the fluid.3. With the separation of the char from the bed material is the major problem in using this reactor.4. Occasionally used in large-scale projects	Chen et al. (2014); Ding et al. (2016)
3	Spouted bed reactor	The reactor provides the solids with excellent movement, leading to high transfer rates of heat between phases, making them ideal for flash pyrolysis. In addition, the conical sputter bed reactor is ideal for continuous operation, which is particularly important for the larger-scale implementation of biomass pyrolysis. Spouted beds have been successfully implemented for pyrolysis of a number of polymers including polystyrene, polyethylene, polypropylene and polyethylene terephthalate. In this type of reactor, waste plastics melt as they are fed into the reactor and, due to their cyclic movement, provide a uniform coating around the sand particles. It also provides high heat transfer with sticky solids from plastics between phases and smaller defluidization problems.	1. In comparison with the bubbling fluidized bed, the spouted bed reactor presents interesting conditions for the pyrolysis of waste plastics due to low bed segregation and lower attrition.2. This reactor is ideal for the handling of irregularly textured particles, fine particles, sticky solids and broadly dispersed particles.3. In addition, with respect to gas flow, the device has great flexibility, allowing operation with short residence times for gas.4. The pattern of solid flow and the spout’s action reduces the agglomerate formation.	1. There is still no data on the use of this reactor with mixed MSW.2. They need very tiny pieces of feedstock.	Amutio et al. (2012); Çepelioǧ; ullar and Pütün, 2013; Niksiar et al. (2015)
4	Rotary kiln reactor	In the slow pyrolysis of MSW, rotary kiln reactors were used and normally performed at temperatures of around 500 C with a residence time of around 1 h.It is vital that solid waste of different shapes, sizes and heating values can be fed either in batches or continuously into a rotating kiln; this feature makes it possible to use this type of reactor extensively. Rotary kilns provide improved heat transfer to the feedstock than fixed beds and are less difficult to run than fluidized beds at the same time.In the pyrolysis process, the residence time of the feedstock in the reactor is a very significant parameter since it defines the energy obtained at a given heating rate by the charge. Residence time is usually a function of the mean volumetric flow and the rotational speed of the kiln in rotary kilns.	1. This is the only type of reactor that has so far been successfully implemented on different scales as a practical industrial solution.2. The slow rotation of an inclined kiln causes the waste to be blended well more uniform pyrolytic products can therefore be obtained.3. The versatile residence time change will make the pyrolysis reaction easy to conduct under optimum circumstances.	1. Feedstock needs some pre-treatment of MSW before pyrolysis.2. Waste should be sorted and then shredded to remove unwanted materials.3. Large-scale implementation is tough.	Li et al. (2002); Fantozzi et al. (2007)
5	Microwave assisted reactors	Microwave energy is derived from electrical energy and most of the domestic microwave ovens use the frequency of 2.45 GHz. The transfer of energy occurs as a result of interaction between the molecules and atoms using microwave. The whole process of drying and pyrolysis are carried out in a microwave oven chamber connected to electricity source. The carrier gas is inert and is also used to create oxygen-free chamber. The reactor has proven to be highly effective in chemical recovery from biomass.	1. Microwaves are the uniform and fast internal heating of large particles of biomass.2. Immediate reaction to fast start-up and shut-down.3. High energy efficiency.4. No need for controllability and agitation.	1. The particles in the feedstock must be very small.2. To avoid secondary cracking reactions, the organic vapours should be removed very quickly from the reactor.3. High running costs due to the high consumption of electrical fuel.	Lam and Chase (2012); Zhang et al. (2014)
6	Plasma reactors	Plasma is a gaseous mixture of negatively charged electrons and positively charged ions produced by intensively heating a gas or by exposing a gas to a powerful electromagnetic field. Two major plasma classes exsist, namely plasma fusion and gas discharges. A direct current or alternating current electrical discharge or radio frequency induction or microwave discharge may be used to produce thermal plasma. To generate plasma, also a 2.45 GHz magnetron available from a commercial microwave oven can be used. As carbonaceous waste-derived particles are pumped into a plasma, they are heated very quickly, releasing and cracking the volatile matter, resulting in hydrogen and light hydrocarbons such as methane and acetylene. Only two streams are formed by thermal plasma pyrolysis of organic waste: a combustible gas and a solid residue, all of which are useful products and simple to handle. Gas yields range between 50 and 98 percent by weight.	1. Easy manageability.2. Enables fast heating.3. Work effectively at relatively4. low power consumption	1. High operating costs.2. Small particle sizes required.	Tang and Huang (2005); Huang and Tang (2007)
7	Solar reactors	The method was performed under an argon flow in a transparent Pyrex balloon reactor. The feedstock was mounted in a black foam insulated graphite crucible located at the centre of a 1.5 kW vertical-axis solar furnace. Without any external heating sources, this construction enables the device to achieve temperatures between 600 °C and 2000 °C.	1. Solar reactors have to be given more attention for their ability of using renewable energy resources to provide energy to endothermic reactions makes pyrolysis more environmentally friendly.2. Char composition decreases with high temperatures and heating rate.	1. Still in laboratory-scale study only.2. Weather dependent	Zeng et al., (2015)
8	Vacuum pyrolysis reactor	In this reactor the feedstock is conveyed into the vacuum chamber with a high temperature with the aid of a conveyor metal belt with periodical stirring by mechanical agitation. The heat carrier normally consists of a burner while the feedstock is melted using molten salts by heating inductively. It has the potential to process feedstock of larger particle size, but needs special solids feeds to specialised discharge devices to provide an efficient seal all the time. Under very low pressures, which can be around 5 kPa, vacuum pyrolysis is performed. This is a slow pyrolysis reactor with a very low rate of heat transfer. This usually results in lower bio-oil yields in the range of 35–50 percent by weight.	1. They have a short organic vapour residence time in the reactor.2. Low temperature of decomposition.3. These two factors decrease the frequency and strength of secondary reactions.	1. The design is extremely complicated.2. Expenditure and maintenance requirements are often heavy, rendering the technology uneconomically acceptable.	Garcìa-Pérez et al. (2007); Zhou and Qiu (2010).

Considering the advantageous nature of pyrolysis techniques and its capacity in effective dealing of municipal wastes, the same can be enforced for the treatment of COVID-19 waste. The technology utilizes high-temperature combustion, which can be applied for complete degradation of the infectious agents that are carried along with the COVID-19 waste. The major aspect that has to be considered would be the safe transport of CW to the Common Medical Waste Treatment and Disposal facility (CMWTF). In some developed or underdeveloped countries, there have been reports on improper handling of CW, which has led to the contamination with the local municipal waste with the virus load and caused rapid spreading among the communities (Hong et al., 2018; Ilyas et al., 2020).

Pyrolysis is a rapid thermochemical process where the degradation of waste takes place in the complete absence or limited supply of oxygen at particular temperatures (known as pyrolysis temperature) for some specified time. These conditions help in the breakdown of complex hydrocarbon compounds into smaller molecules. Relatively essential products like gases, liquids, and solid char are formed. Commercially important products so formed during the pyrolysis process are based on several factors like concentrations of the waste, pyrolysis temperature, heating rate, particle size and catalyst (Basu, 2018). Pyrolysis is classically carried out in a temperature range from 300 to 650 °C. The primary degradation of waste by the pyrolysis process forms condensable gases and solid char. Further, the gases formed would undergo secondary decomposition leading to the evolvement of non-condensable gases (CH4, CO2, CO, H2), liquids and char. Bio-oil or liquid product formed during the pyrolysis process is the most important because it resembles commercial fossil fuels properties. Char is the solid product that is evolved during the decomposition of waste, and they have the properties of carbon sequestration (Trapping of CO2) (Qin et al., 2018a, 2018b; Al-Salem, 2019).

Generally, during pyrolysis, plastic waste produces the end products as liquid oil and gases with small fractions of condensed by-product as char. Char is the constituent of carbon-rich materials that occur in the plastic waste as inorganic compounds. Char has a comparable high heating value of 34 MJ/kg like the coal feedstock, but it also carries a few heavy metals and harmful elements such as sulphur, chlorine and nitrogen. It is a necessity to access the constituents of char which can provide details if it carries any harmful substances which can affect the environment. Further, it can be used as combusting material in the pyrolysis process itself (Zeng et al., 2015).

Char also possesses similar properties to activated carbon because of its high carbon content. Since char is the product derived from plastic waste, which can be a cost-effective replacement for activated carbon, they have excellent adsorptive properties that can be utilized for the production of activated carbon (Widiyannita et al., 2016). It has been estimated the char carries metals like magnesium, calcium, potassium and iron at a significant level but however other heavy metals like zinc (Zn), chromium (Cr), nickel (Ni), molybdenum (Mo), manganese (Mn) and aluminum (Al) also present in negligible amounts. Certain sequential solvent extraction process helps in the significant removal of magnesium, calcium and potassium (Lee et al., 2012).

Tar is the by-product that is released on thermochemical reactions of plastic waste and they mostly contain highly condensed hydrocarbons. Tar formation sometimes leads to the release of carcinogenic compounds, deactivating the catalyst in the reaction and also disturbing the desired product formation (Huang et al., 2012). These tars are formed at a temperature range from 180 to 300 °C which forms a coating layer or deposits in engines, turbines and they are most difficult to remove. It is based on the nature of the plastic waste tar formation occurs. The primary aromatic tar is formed on the degradation of polymers such as PS and PET (Balas et al., 2014). Alkanes and alkenes types of volatile tar are formed from the combustion of PP and PE. The primary tar components which are unstable in nature may lead to the production of more stable structures of secondary and tertiary tar. Mostly these tars formations occur in gasification rather than the pyrolysis process (Wilk, 2013).

General thermochemical reaction that takes place in the pyrolysis techniques is represented as:

Pyrolysis has been broadly classified into four types, namely 1) Slow, 2) Conventional 3) Fast and 4) Catalytic. In slow pyrolysis, the vapour residence time (VRT) is in the order of minutes or more than that, whereas in the fast pyrolysis process, the VRT will be in the order of seconds or milliseconds. Slow pyrolysis has been further classified as carbonization and torrefaction. They are mainly differentiated by the operating temperatures (OT) and vapour residence time (VRT). Fast pyrolysis is classified into two types, namely, i) Flash and ii) Ultrarapid, and the main product formed would be bio-oil and gases. In catalytic pyrolysis, the oxygen content of the product (Bio-oils) formed is vastly reduced by the addition of a catalyst, which increases its stability, energy density and acidity reduction (Al-Salem et al., 2017; Qureshi et al., 2020). Each pyrolysis process is briefed below.

Slow pyrolysis

It is one of the oldest forms of pyrolysis in which the feedstock or CW is slowly heated for an extended time at a low temperature of below 400 °C in the absence of oxygen for several days. This slow thermal process helps in the maximal production of char. Slow pyrolysis process is further classified into carbonization and torrefaction. The carbonization process operates at higher temperatures (above 300 °C to 400 °C) and possesses longer residence time, while the torrefaction process utilizes very low and narrow temperature (200 °C–300 °C) as well as lesser residence time. In the carbonization process, the feeding stock or CW upon slow pyrolysis gets converted to highly stable carbonaceous products, namely charcoal or char and non-condensable gases, which are excellent sources of fuels. In the metallurgical industry, charcoal has been widely used as a reductant in the smelting and sintering processes. Char is formed during slow pyrolysis, which on further processing forms the activated carbon as a product and they have the property of good absorbent. Torrefaction is a thermal process that converts the feeding stock or CW to coal-like substances and they are highly brittle, less energy-intensive and can also be used as fuels (Das and Tiwari, 2018).

Conventional pyrolysis

In this method, the feeding stock or CW undergoes a thermal degradation process at moderate temperatures below 600 °C and product residence time will be in the order of minutes. Their main product yield that is formed at the end of the process would be bio-oil, gases, and char (Czajczyńska et al., 2017).

Fast pyrolysis

It is the process in which the feeding stock or CW upon rapid heating at maximal temperatures (above 1000 °C) produces certain valuable products, which can be used as an alternative for the commercial fuels. However, CW gets disintegrated or decomposed at a lower peak temperature of 650 °C to form bio-oil, acting as an excellent substitute fuel. The same CW upon thermal degradation above 1000 °C yields gases. Bio-oil or liquid fuel production yield can be effectively increased by adopting certain steps like 1) rapid heating, 2) reaction temperature maintained in the range of 425 –600 °C, 3) less residence time of below 3 sec in the reactor and 4) rapid cooling (Quenching) of the vapourised gases to form liquids (Venderbosch and Prins, 2010).

Flash pyrolysis

In this process, moderate heat of 450–600 °C at a short residence time of 0.03–1.5 s is supplied in the reactor, which converts the CW into condensable and non-condensable gases. This method helps in condensing vapours into liquids or bio-oils, thereby reducing the amounts of char formation. The total yield of bio-oil formation in the flash pyrolysis process would be accounted for more than 70–75% (Voudrias, 2016).

Ultrarapid pyrolysis

It involves extreme heating of feeding stock or CW at a relatively higher temperature of 700 –1000 °C upon a very short duration of below 0.5 s. The reactor can achieve a maximum yield of bio-oil or liquid fuel of around 90% and a very low amount of >10% char will be collected. A temperature of >700 °C will be suitable for bio-oil production and <1000 °C condenses more gases (Aboughaly et al., 2020).

Catalytic pyrolysis

In catalytic pyrolysis, the thermal degradation of feeding stock or CW occurs by using suitable catalysts at different temperatures (300–900 °C) in the absence of oxygen. An appropriate catalyst might alter the reaction network during the process and lead to the in-situ upgrade of the bio-oil produced. In promoting process efficiency, targeting particular reactions and reducing process temperature and time, catalysts play a very critical role. In this pyrolysis processes, a wide variety of catalysts have been used, but ZSM-5, zeolite, Y-zeolite, FCC, and MSM-41 are the most commonly used catalysts (Al-Salem et al., 2017; Miandad et al., 2019).

In CPW pyrolysis, catalysts are typically used to boost the reactions, which vastly influence product formation in the reactor. Catalytic cracking is quicker than the process of thermal cracking, which needs lower temperatures and energy requirements. Moreover, the use of catalysts like zeolites results in higher yields of petrol, gasoline and hydrocarbons (Aguado et al., 2006). Thermal pyrolysis of plastic waste yields products of lengthy hydrocarbons, whereas use of catalysts in the process can shorten the carbon chain length of the product’s formed (Garforth et al., 1998). Some catalysts can also be used to reduce the degree of unsaturation in certain hydrocarbon products and also increased yield of diene and aromatic products which can improve the stability of these products as well as their cetane count. The activation energy of plastic waste pyrolysis was reported to decrease when HZSM-5, HY, and MCM-41 were the catalysts that were used. Therefore, catalysts are beneficial because they minimize operating rates by reducing heat capacity and can produce highly required liquid fuels (Lerici et al., 2015).

In pyrolysis, there are two kinds of catalysts, namely Homogenous and heterogenous are used and they are graded according to their participation in the reactions. Homogeneous catalysts are in the same phase as that of the reaction medium, whereas heterogeneous catalysts are present in a different phase. Lewis acids, such as aluminum chloride, are the most common homogenous catalysts, and heterogeneous catalysts include widely used nanostructured zeolites, superacid solids, mesostructured catalysts, carbon-supported metals, and basic oxides. The use of solid catalysts typically increases liquid and gaseous fraction selectivity. Catalytic co-pyrolysis of plastics and biomass has been found to be feasible and, in such situations, it would not be necessary to sort feedstock before pyrolysis. In addition, the plastic to biomass concentrations can be changed to attain the desired liquid oil and gaseous products (Serrano et al., 2010).

Pyrolysis was found to be more advantageous than the incineration technology for the treatment of CW or CMW because it exhibits high energy production, value-added product generation and reduction in the evolution of pollutants. The products generated after the pyrolysis treatment have a wide scope of uses, from excellent fuels to fine chemicals. Pyrolysis can effectively diminish the dangers of alkali volatilization, fouling, slagging, bed agglomeration, which is encountered during the incineration process of treating the waste (Kim et al., 2020). CW or CMW carries mostly organic compounds that get volatilized on high thermal treatment and are made to pass into the secondary chamber, where they get condensed and converted to economically important liquid fuels. These liquid fuels closely resemble the properties of commercially available fossil fuels. Solid products and other gases produced after pyrolysis have high economic value and can be used as alternative energy sources (Quesada et al., 2019; Fang et al., 2020).

The main components of medical waste are personal protective equipment, facemasks, aprons/gowns, nitrile gloves, which were mostly made from plastics composed of polypropylene, pppolyethylene, polyethylene terephthalate, polystyrene (Table 3 ; Fig. 4 ) (Windfeld and Brooks, 2015; Nirban and Upendra, 2019). During pyrolysis, these components start decomposing at 300 °C and maximal is reached around 400 °C under inert conditions, which releases certain substances like hydrocarbons and some gases (hydrogen, methane, acetylene, ethylene, ethane, propene, Butatriene) (Qin et al., 2018a, Qin et al., 2018b; Zroychikov et al., 2018). These gases that evolved during the pyrolysis process were identified and analyzed using a mass spectrometer and their activation energy was found to be about 52.70 kJ/mol. From GCMS analysis of medical waste products, particularly bio-oil, it was found to contain around 25 types of compounds having ten to twenty length chain of carbons, which is similar to the components present in any commercial petroleum products (Fang et al., 2020). Various types of plastic waste generated from different sources during COVID-19 and their energy yields upon pyrolysis treatment process are shown in Table 4 .

Table 3

Types of plastic waste generated from various sources during COVID-19 and their energy yields upon pyrolysis treatment process.

S. No.	Sources	Types of plastic waste	Carbon ratio (%)	Pyrolysis temperatures (°C)	Energy yields (%)			Other substances	References
					Liquid oil	Gases	Char
1	Fruit juice bottles, soft drink bottles, mineral water cans	Polyethylene terephthalate (PET)	63.94	500	38.9	52.1	8.9	–	Sharuddin et al. (2017); Erdogan (2020); Sharuddin et al. (2018)
2	Detergent bottles, milk bottles, toys, oil containers	High-density polyethylene (HDPE)	86.99	350	80.9	17.2	1.9	–	Luo et al. (2000); Kyong et al. (2002); Abbas-Abadi et al. (2013); Ahmad et al. (2014)
				400	82	16	2	–
				450	91.2	4.1	4.7	–
				500	85	10	5	–
3	Plastic bags, garbage bags, wrapping foils for packaging	Low-density polyethylene (LDPE)	85.6	425	89.5	10	0.5	–	Williams and Williams (1998); Onwudili et al. (2009); Marcilla et al. (2009); Fakhrhoseini and Dastanian (2013)
				500	80.4	19.4	0.2	–
				550	93.1	6.9	–	–
				600	51.0	24.2	–	Wax - 24.8
4	Water pipes and electrical insulations	Polyvinyl chloride (PVC)	37.24	500	12.79	87.7	–	–	Sharuddin et al. (2017); Erdogan (2020)
				520	12.8	0.34	28.1	HCl – 58.2
5	Facemask, packaging, as plastic parts in automotive industry, special devices like living hinges, and textiles	Polypropylene (PP)	86.88	300	69.8	28.8	1.3	–	Sakata et al. (1999); Ahmad et al. (2014); Abbas-Abadi et al. (2014); Erdogan (2020)
				380	80.1	6.6	13.3	–
				400	85	13	2	–
				450	92.3	4.1	3.6	–
				500	82.1	17.76	0.12	–
6	Construction, electronics, medical appliances, food packaging, and toys.	Polystyrene (PS)	91.57	400	90	6	4	–	Kyong et al. (2002); Demirbas (2004); Adnan et al. (2014)
				425	97	2.5	0.5	–
				500	96.7	3.27	–	–
				581	89.5	9.9	0.6	–

Fig. 4

Common plastic components present in the COVID-19 medical waste.

Table 4

Products generated during the pyrolysis process of COVID-19 plastic waste treatment using different types of reactors.

S. No.	Types of plastic waste Generated from CMW	Types of Reactors used for the pyrolysis treatment	Parameters used for pyrolysis process		Products formed after the process	References
			Temperature (°C)	Heating rate (°C/min)
1	Polyethylene terephthalate (PET)	Fixed-bed reactor	500	6	Bio-oil and Gas	Fakhrhoseini and Dastanian (2013); Erdogan (2020)
2	High-density polyethylene (HDPE)	Semi-batch reactor	550	10	Bio-oil and Gas	Ahmad et al., (2014)
3	Low-density polyethylene (LDPE)	Fixed-bed reactor	500	10	Bio-oil, Gas and Char	Marcilla et al., (2009)
4	Polyvinyl chloride (PVC)	Fixed-bed reactor	500	10	Gas as major product with less percentage of Bio-oil	Erdogan, (2020)
5	Polypropylene (PP)	Batch reactor	500	10	Bio-oil, Char and Gas	Ahmad et al., (2014)
6	Polystyrene (PS)	Semi-batch reactor	400	10	Bio-oil and Gas	Onwudili et al. (2009); Erdogan (2020)

Polyethylene (PE) is said to be lightweight, durable thermoplastic. This component was used in making films, tubing, plastic bags, packaging materials and bottles. PPE and packaging materials used in hospitals were made from polyethylene. PE is formed by polymerization of ethylene C2H4, often facilitated by Ziegler- Natta catalyst (Settele et al., 2020). There are different types of polyethylene, such as HDEP (High-density polyethylene), LDEP (low-density polyethylene), ultra-high molecular weight polyethylene (UHMWP). The structural variability and relative chemical inertness of PE have relegated most studies on PE recycling to variations on pyrolysis. There are two major processes for the pyrolysis of PE: thermal or catalytic pyrolysis. Thermal pyrolysis is simply heating PE at high pressure to break down the polymer backbone to form smaller organic molecules. Catalytic pyrolysis utilizes a catalyst in an effort to reduce the temperature and reaction time and thus improve the economic viability and, in some cases, the selectivity (Goto et al., 2002). One of the studies concludes that during the thermal pyrolysis of commercially available HDPE at 380 °C, it gives an oil-like product in the yield of 81%. The end product of pyrolysis is said to be paraffin hydrocarbons comprising 6 and 16 carbon atoms (Moriya and Enomoto, 1999).

Polypropylene (PP) consists of a similar backbone to PE but has an extra methyl group on its side chain. PP is a lightweight, tough, crystalline thermoplastic polymer found in reusable food containers, the automotive industry, and even the furniture market. PP is synthesized from the propylene (C3H6) using either a Ziegler–Natta or metallocene catalyst. PP can have three different types of structures, atactic, isotactic, and syndiotactic (Wang et al., 2009). PP’s thermal degradation is more severe than in PE because the tertiary carbon atom present in the PP backbone is susceptible to thermo-oxidative and photo-oxidative degradation (US EPA, 2009). In this process, PP was depolymerized in an induction-coupled plasma reactor. Under these conditions, PP was converted to gaseous products (up to 78 wt%) and of the gaseous product formed 94% was identified as propylene. (Teotia et al., 2017). Supercritical water to convert PP into oil. Optimal reaction conditions were found to be at 425℃ for 2–4 h or 450 ℃ for 0.5–1 h, in which case up to 91 wt% of the PP was converted into oil. The composition of the oil was found to be olefins, paraffin, cycloalkanes, and aromatics (Troev et al., 2003).

Polyethylene terephthalate (PET) is a semi-crystalline, thermoplastic, lightweight, strong and clear material used as fibers, sheets and films, and more specifically, it is used in the food and beverage packaging (especially, soft-drink and water bottles), electronics, automotive parts, housewares, lighting products, power tools, sports goods, photographic applications, X-ray sheets and textiles. PET is known for its high strength and mechanical stress handling (Geyer et al., 2017). PET is formed by a polycondensation reaction between terephthalic acid (TA) and ethylene glycol (EG) or through a transesterification reaction between dimethyl terephthalate (DMT) and EG (Silvestre and Cimmino, 2013). PET undergoes pyrolysis to yield an end product such as monomers, TA and EG. Three different types of hydrolysis have been studied in the greatest detail: acidic, alkaline, or neutral hydrolysis. While acidic hydrolysis can occur using concentrated acids, such as phosphoric or nitric, the most common acid used is sulfuric acid.

Polystyrene (PS) is a petroleum-based plastic that contains benzene, usually brittle and transparent which is carcinogenic in nature. Long-term exposure of styrene can be neurotoxic and cause cytogenic, carcinogenic and hematological effects (Aboulkas et al., 2010). PS is used to manufacture cheap transparent kitchenware, light fittings, bottles, toys, food containers, etc. (Proshad et al., 2018). PS is a synthetic aromatic polymer with high molecular weight (formula (C8H8) n) made from the monomer styrene. PS is a durable thermoplastic that is generally believed to be non-biodegradable. Biodegradation of PS does occur but at a very slow rate in natural environments and therefore, PS persists for long periods as solid waste. A study shows that cultivated soils containing a wide range of fungi, microbes, and invertebrates, degradation of PS is less than 1% after 90 days with no significant increase in degradation rate after this time (Plastics-the Facts, 2016). In oxidative atmospheres, carbon monoxide (CO), carbon dioxide (CO2) and oxidative hydrocarbons are formed. The concentrations of CO and CO2 are a function of temperature and combustion conditions, i.e., greater amounts are produced in the flaming than in the non-flaming mode (Rubio, 2015).

Factors influencing the pyrolysis of COVID-19 plastic waste

Temperature

One of the most critical parameters which direct the cracking of polymers present in the plastic waste. This cracking occurs when the carbon chains’ Vander wall forces get weakened and generate energy greater than the chains’ carbon bonds. Because of this action, plastic waste with high molecular weight gets decomposes rather volatile (Sobko, 2008). It has been concluded from certain experiments that cracking occurred at different temperatures, which would be based on the reactor as well as the loss of heat. But the temperature factor has a direct influence on the product formed. Predominant products that are formed after the plastic waste pyrolysis would be the liquid oil, gases and certain hydrocarbons—the increased temperature of above 600 °C triggers lighter hydrocarbon productions. Wax and liquid oil productions are encouraged at the temperature range of 400–600 °C treatment of plastic waste. Below 400 °C of the treatment leads to the formation of viscous liquid products and other secondary products (Xingzhong, 2006).

Pressure

Reactor pressure plays an important role in the pyrolysis thermochemical reactions of the plastic waste. High pressure at a particular temperature favors the cracking of the reactions rather the vaporization factors because of increased boiling points. But their effects are substantial at some temperatures only. Certain types of plastics don’t get influenced by the pressure factors though they rise above 430 °C since their reaction boiling points are below at lower temperatures. High pressure has a definite influence on the cracking of the bonds of the waste polymers, which lowers gaseous products production. Though this pressure favors liquid oil production efficiently but its added parts like compressors and the cost of its sensors are high, which increases its operational cost (Bridgwater, 2012).

Reactors

Types of reactors applied in the pyrolysis process vastly influence other factors like heat transfer rate, mixing of plastic, residence time, product distribution, the product itself and the catalysts used in the reactions. The plastic waste supplied in batches in the pyrolysis process of batch reactors and the formed products like liquid oil and gases were also collected in batches (Lerici et al., 2015). On the contrary, both the feeding of plastic waste and the substance produced are given constantly in a continuous reactor. In a semi-batch reactor, the feedstock is applied batch-wise, but the products formed following the reactions and are continuously extracted. Batch and semi-batch reactors are preferable for research or laboratory scale, but for industrial purposes, the continuous reactor would be more suitable for the faster product development (Serrano et al., 2010).

Pyrolysis reactors can also be classified according to the processes of heat transfer and the flow directions of their feeds and materials. Under this system, they are a series of reactors such as fixed bed, fluidized bed, microwave thermolysis and screw kiln (Fig. 5 ) (Saad et al., 2015; Chattopadhyay et al., 2016; Lopez et al., 2017; Basu, 2018; Campuzano et al., 2019). Pyrolysis occurring in a fixed-bed reactor makes it easier to build and easier to run, but since the plastic waste has low thermal conductivity, which can produce a wide temperature gradient in a batch method as well as in the continuous but due to the irregular feedstock shapes, they face feeding problems. So, these types of reactors are not to be fit for industrial purposes. Fluidized bed reactors are used in most commercial plants because they run continuously and transfer heat and mass better than the fixed bed. Recently there are reports on usage of screw kiln reactor in plastic waste pyrolysis and extruder which provides external heat for the reactor. The plastic waste feeds are screwed from the pretreated feeder to the reactor chamber. The rotation of the extruder can be altered to monitor the feeding rate and, consequently, the residence time (Syamsiro et al., 2014).

Fig. 5

Different types of reactors that are used for the treatment of COVID-19 plastic waste (Saad et al., 2015: Lopez et al., 2017; Basu, 2018; Campuzano et al., 2019, reproduced with permission).

Residence time

It is categorized into solid residence time and vapour residence time. Solid residence time is the period spent before it is completely degraded in the solid feed reaction, while vapour residence time is the time taken by the generated vapour to exit the reactor. Residence time can be regulated by changing the feeding rate or product discharge rate. More side reactions favoring the production of char and other stable products arise from long periods of solid residence (Anuar Sharuddin et al., 2016). Similarly, longer vapour residency periods promote primary vapour products’ conversion into less volatile products at temperatures around 500 °C, such as non-condensable petroleum gases and aromatics.

Furthermore, a lower percentage of oil in the product and a higher percentage of char result in longer residency periods for vapour. Residence time would directly impact the products produced at those temperatures only (Papuga et al., 2016). A research report found that there were not many improvements in gas and oil end products above 685 °C. They also found that the higher oil yield below 685 °C resulted in a longer residence period. Therefore, since the effect at high temperatures becomes less evident, most researchers conduct their plastic pyrolysis experiments without much regard to the effects of residence time. However, at temperatures below 450 °C, residence time is a vital factor that must be taken into account (Mastral et al., 2003).

Plastic materials

Plastic waste itself is the factor that influences the product formation during the pyrolysis process. polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET) and polyvinyl chloride (PVC) were the basic components present in COVID-19 plastic waste. The regular repeating units of monomers were made of each plastic component present in COVID-19 plastic waste and the way they are paired with each other influenced thermal degradation properties. In straight chains, linear polymers have their monomers linked, and branched-chain polymers have side chains connected along with their regular chains (Wu and Williams, 2010). When the components of plastic waste present in COVID-19 plastic waste are subjected to high thermal conductivity in the pyrolysis reactor, their stability begins to be lost so rapidly, their attractive forces are broken between the bonds in each polymer and thus become soft. Some crosslinked polymers exist apart from mono or branched polymers found in plastic waste, and they have long chains of molecules with good characteristics of a covalent bond. During pyrolysis at high temperatures, these crosslinked polymers do not melt; rather than start cracking, they release useful energy-bearing products such as liquid oil, gases (syngas, hydrogen gas), hydrocarbons (HCs) and charcoal (Gao, 2010).

The most common methods adopted in refining and upgrading the liquid fuels or bio-oils obtained from the treated medical waste by pyrolysis technique include emulsification, catalytic hydrogenation, fractional condensation and distillation. Among them, the most promising approach would be the fractionation of pyrolysis products, which efficiently separates out the liquid fuel or bio-oils and the fine chemicals (Zaman et al., 2017; Erdogan, 2020; Fang et al., 2020). Separating the fractions and simultaneously continuing the condensation process significantly enhances the recovery of liquid fuels. Due to high-temperature fractional condensation, the liquid fuels or bio-oils’ water and oxygen contents are greatly reduced. The collected components exhibit the same behavioral pattern of existing petroleum products. In a previous study, three-stage condensation was carried out for the products evolved from the fixed-bed pyrolysis treated feedstock. Pyrolysis parameters like temperature and fractional condensation temperature were correlated (Johansson et al., 2016). It was noted that the highest liquid fuel or bio-oil separates at three different pyrolysis temperature at 450 °C, 500 °C and 550 °C, when the three-stage condenser temperature were at 110 °C, 0 °C, and −196 °C. Thus, it clearly proves that fractional condensation temperature dramatically influences the product yields (Fig. 6 ) (Fang et al., 2020). In another report, five-stage condensation was adopted and this yielded liquid fuels or bio-oils with less moisture content and acidity. Other products like pyrolytic lignin and levo-glucan were obtained at the first two stages itself (Pollard et al., 2011; Ma et al., 2018). A multi-stage condenser usage helps collect high-quality liquid fuels and recover other valuable byproducts compared with another factional condensation system after the pyrolysis process (Papari and Hawboldt, 2018). Therefore, similar techniques or technology can be adopted for processing the CW or CMW to get converted into useful products like liquid fuels or bio-oils, which can act as a better replacement for fossil fuels (Klemes et al., 2020).

Fig. 6

Fractional condensation device setup for the pyrolysis oil obtained from the thermal degardation of plastic waste.

As a promising medium for the thermochemical conversion of waste polymers to useful chemicals and fuel additives, catalytic fast pyrolysis (CFP) has been widely accepted. By removing and substituting oxygen and oxygen-containing functional groups, catalytic upgrading of pyrolysis oils improves the final products H/C ratio and energy density. In order to optimize the resulting bio-oil yields and properties, such as composition and stability, various catalyst forms, metal oxide, molecular sieve, mineral, transition metals, etc., have been studied (Wang et al., 2015).

In order to lower reaction temperatures and improve product delivery, catalysts have been studied for the CFP of waste polymers. In the resulting oil, HZSM-5 catalyzed PP pyrolysis will reduce BTX formation temperature from 700 °C for pure PP to 300 °C with three main compounds, i.e., alkenes, dienes, and aromatics. This is an essential influence on the pyrolysis processes of both the polymer microstructure and the feed mixture. Pyrolysis of pure HDPE using HZSM-5 has, on the other hand, significantly increased the production of gaseous products, particularly C10–C16 hydrocarbons (Palza et al., 2017).

In the pyrolysis furnace, the solid product obtained by pyrolysis of medical plastic waste was mainly the solid residue remaining and the carbon black produced. A gas chromatography-mass spectrometry was used to assess the chemical compositions of liquid products. Gas chromatographs equipped with thermal conductivity detectors (TCD) and flame ionization detectors have detected the gaseous substance (FID). The obtained liquid product was black sticky paste tar. The heating value measured by automatic calorimeter was 8972.82 kcal/kg, which was only slightly lower than the heat value of gasoline stipulated in the national standard (10,300 kcal/kg). There has been a preliminary analysis of its composition and GC-MS carried them out and due to the complexity of the composition of liquid product, only the components with a large content were listed, mainly including alkanes, olefins, ketones, esters, alcohols, etc. The relative yields of olefins, alkanes, and lipids were found and these liquid products have a carbon chain length in the range of C6 to C28, which possess similarities to diesel. It indicates that H2, CO, and many combustible organic gases were the gaseous pyrolysis product’s main constituents (Fang et al., 2020).

Conclusion

The COVID-19 pandemic has continuously caused significant harm to individuals across the globe. The virus has taken up a lot of life, and it still exists. Apart from this, the prospect of the accumulation of enormous amounts of COVID-19 waste causes the most alarm. These are majorly sourced from hospitals, healthcare centers and even household wastes (packaging plastics used for foods, groceries, PPE). Generally, CW or CMW are considered hazardous in nature because they carry highly infectious agents along with them. The constant increase in CW or CMW quantity makes it imperative for new and better waste treatment methods to be created. Traditional waste management methods, such as composting, landfilling, and incineration, are obsolete and replaced by new reliable and easy-to-run solutions. One of the techniques that have high potential and can be effectively applied for the treatment of CW or CMW would be pyrolysis. It is a thermo-chemical process wherein any raw-material (biodegradable or non-degradable) carrying organic carbon can be easily decomposed. The products are liquid oil and small portions of solid char. The liquid oil produced has characteristics similar to that of the commercial fossil fuels, whereas the char so formed has the properties of carbon sequestration. Also, the COVID-19 pandemic has led to an increase in the enormous amount of plastic wastes. These non-renewable polymers upon pyrolysis result in the formation of syngas, HCs and H2 gas. Pyrolysis may also be an environmentally benign and process-efficient way of handling plastic waste from COVID-19, producing value-added products simultaneously. Pyrolysis makes it a simpler and cleaner way to turn waste into energy products, such as ready-to-use fuels. Other technology like incineration of plastic waste may lead to the emission of toxic pollutants such as dioxins and furans, which needs additional flue-gas treatment facilities. As we look forward to a post-COVID-19 future, it will be of primary concern to counter fear-driven prejudices toward hygiene of reused and recycled goods. Investments in safety gear and physical facilities for sorting, collecting, and recycling will restore sanitation workers trust in the safety of waste handling and contribute to clear, homogeneous plastic streams for recyclers. Automation and creativity in current and emerging technologies, such as the inculcation of artificial intelligence into collection and segregation, will reduce the load on manual systems and provide waste management services effectively.

Generally, waste management is one of the major and challenging sectors for every country. Recently, the Covid 19 pandemic has overstressed this sector, entrenching new challenges against the conventional practice. Therefore, to address this situation, proper action must take care of waste management at the same level of public health and safety. The current waste generation techniques and their poor management must be appropriately examined and treated to save the environment and human health. In this view, the following considerations must take care of seriously for maintaining the proper waste management.

The postponed medical waste service should be reopened and treated properly

For collection and safe disposal of household waste management, a proper guideline can be passed through social media apps or advertisement

Incorporation of reusable PPEs in response to immense PPEs usage

Plastic waste management and circular economy

Hazardous waste needs to be treated through thermal treatment (e.g., pyrolysis) or incineration techniques.

Credit statement

The authors: Selvakumar Dharmaraj, Veeramuthu Ashokkumar, and Rajesh Pandiyan involved in data collection, manuscript preparation and writing. The authors Heli Siti Halimatul Munawaroh, Kit Wayne Chew, Wei-Hsin Chen, Chawalit Ngamcharussrivichai, helped in writing, reviewing, and editing the manuscript.

Declaration of competing interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.