| Literature DB >> 32012779 |
Lorenzo Brognara1, Emmanuel Navarro-Flores2,3, Lorenzo Iachemet1, Nuria Serra-Catalá4, Omar Cauli2,3.
Abstract
New treatments based on peripheral stimulation of the sensory-motor system have shown to be promising in rehabilitation strategies for patients with neurological disorders, including Parkinson's disease (PD), especially in regards to reducing gait impairment, and hence, the incidence of falls. The aim of this study was to evaluate the change in several gait parameters measured by sensor inertial measurement in PD patients after acute plantar stimulation, under the distal phalanx of the big toe, and underneath the head of the first metatarsal joint of both feet, using a 3D printing insole. In order to assess whether the effects are selective for PD patients, we compared the effect of the treatment in a control group (age-matched) consisting of patients with other neurological disorders which also displayed gait and balance impairment, and a similar cognitive function, depressive symptoms, body mass index, and comorbidity burden observed in the PD group. Plantar foot stimulation in PD patients eliminated the significant (p < 0.05) alterations existing in stride asymmetry and in stride variability. When comparing the effects of post-plantar stimulation with the respective basal level, considered as 100% in both groups, we observed a significant (p = 0.019, Mann-Whitney test) increase in stride length compared to basal in the PD group and control group. No significant effects of foot plantar stimulation were observed in any of the gait parameters in the control group. Plantar foot stimulation has a positive effect on the step and stride length, and has a positive effect on walking stability, measured by the increase in stride length. No significant effect was observed on bradykinesia because it did not improve walking velocity. These findings indicate that foot plantar stimulation using a 3D printing insole seems to generate a more stable walking pattern in PD patients, with an interesting applicability, and a low-cost, for reducing gait impairment in PD patients.Entities:
Keywords: 3D printing; additive manufacturing; asymmetry; foot; medical device; rehabilitation; stride length
Year: 2020 PMID: 32012779 PMCID: PMC7071420 DOI: 10.3390/brainsci10020069
Source DB: PubMed Journal: Brain Sci ISSN: 2076-3425
The table shows all spatiotemporal parameters of gait analyzed during the pre- and post- mechanical peripheral stimulation.
| Type of Recorded Variable (Unit) | Measurement |
|---|---|
| Variability (s) | Standard deviation of stride duration. |
| Asymmetry (%) | Speed difference between right and left side. |
| Gait speed (m/s) | Ratio between the length and duration of the stride. |
| Stride length (m) | Distance between successive ground contacts of the same foot. |
| Cadence (step/min) | Number of steps per minute (stride frequency). |
| Stride duration (s) | Time elapsed between the first contact of two consecutive footsteps of the same foot. |
| Swing phase (%) | The swing phase is that part of the gait cycle during which the reference foot is not in contact with the ground and swings in the air. It constitutes about 40% of gait cycle. |
| Single support and Double support | Double support (2 times 10%); when only one is in the support phase. |
| Pitch Contact (°) | Contact angle between the foot and the ground during the first step contact. |
Figure 1Details of the realization process of the customized 3D printed insoles design used in this study, (A) and the insoles (C) inside the shoe with the inertial measurement unit attached to shoelaces with a Velcro strap (B). Blue arrows indicate the effect of blunted cones on the foot after mechanical peripheral stimulation on the plantar surface of the first metatarsal joint and distal phalanx (D).
Figure 2Blunted cone’s size (a: 5 mm, b: 2 mm, c: 7 mm).
Psychogeriatric evaluation of study participants. We reported mean ± standard deviation. For comparisons between groups the U Mann–Whitney test. T was used.
| Parkinson’s Disease | Control | ||
|---|---|---|---|
| Performance in the activities of daily life (Barthel score) | 57.9 ± 6.2 | 62.5 ± 3.2 | 0.23 |
| Gait and balance (Tinetti scale) | 12.7 ± 2.6 | 16.3 ± 1.1 | 0.01 |
| Depressive symptoms (Yesavage scale) | 3.7 ± 1.2 | 3.5 ± 0.6 | 0.65 |
| Cognitive function (MEC score) | 28.1 ± 2.6 | 29.6 ± 0.9 | 0.21 |
| Charlson comorbidity (age-adjusted) index | 5.8 ± 1.6 | 5.8 ± 0.5 | 0.71 |
Figure 3Comparison between spatiotemporal parameters of gait before and after mechanical peripheral plantar stimulation. Panels (A–C) represent the mean values before, and panels (D–F) after plantar stimulation. Plantar stimulation was maintained in stand position for 5 min. * p < 0.05 Mann--Whitney test.
Figure 4Comparison of percentage increase in stride length between two groups. Percentage change in stride length of plantar stimulation respect to basal (before plantar stimulation) level. * p < 0.05 Mann–Whitney test.