Drew R Dudley1, Brian A Knarr1, Ka-Chun Siu2, Jean Peck3, Brian Ricks4, Jorge M Zuniga1,5. 1. Department of Biomechanics, University of Nebraska, Omaha, NE, USA. 2. Division of Physical Therapy Education, University of Nebraska Medical Center, Omaha, NE, USA. 3. CHI Health Creighton University Medical Center and an adjunct faculty at the Department of Occupational Therapy at Creighton University, Omaha, NE, USA. 4. Computer Science, University of Nebraska, Omaha, NE, USA. 5. Faculty of Health Sciences, Universidad Autonoma of Chile, Chile.
Abstract
INTRODUCTION: Many individuals with stroke still have functional difficulties with their affected hand after going through a rehabilitation program. A 3D printed upper limb exoskeleton was designed for an individual who had a stroke. Functional and neuromuscular outcomes were measured using his affected hand with and without a 3D printed passive exoskeleton. The goal of this study was to determine the functional and neuromuscular changes induced by the 3D printed exoskeleton in a participant with stroke. MATERIALS AND METHODS: The functional ability of the exoskeleton was assessed using the Fugl-Meyer Assessment and the Box and Block Test. Strength testing and muscle activation of the participant's forearms were measured during maximal voluntary contractions. Furthermore, EMG was measured during the Box and Block Test and satisfaction and usability of the 3D printed exoskeleton were assessed using standardized questionnaires. RESULTS: The exoskeleton improved both the participant's Fugl-Meyer Assessment scores and Box and Block test scores compared to not wearing the device. The subject had increased EMG activation in his extensor when wearing the exoskeleton. CONCLUSION: The inexpensive 3D printed exoskeleton was effective in assisting the participant with stroke during the functional assessments and has the potential to be used to help regain function of the hand in the home setting of an individual with stroke.IMPLICATIONS FOR REHABILITATIONA 3D printed passive hand exoskeleton may assist to accomplish rehabilitation outcomes by increasing function of the affected hand of patients with stroke.The use of this hand exoskeleton may be used to improve gross hand dexterity and assist with functional grasps during rehabilitation sessions with a lower patient's level of perceived exertion.The use of new antimicrobial 3D printing polymers can be effectively implemented to manufacture assistive devices to prevent skin infections during rehabilitation.
INTRODUCTION: Many individuals with stroke still have functional difficulties with their affected hand after going through a rehabilitation program. A 3D printed upper limb exoskeleton was designed for an individual who had a stroke. Functional and neuromuscular outcomes were measured using his affected hand with and without a 3D printed passive exoskeleton. The goal of this study was to determine the functional and neuromuscular changes induced by the 3D printed exoskeleton in a participant with stroke. MATERIALS AND METHODS: The functional ability of the exoskeleton was assessed using the Fugl-Meyer Assessment and the Box and Block Test. Strength testing and muscle activation of the participant's forearms were measured during maximal voluntary contractions. Furthermore, EMG was measured during the Box and Block Test and satisfaction and usability of the 3D printed exoskeleton were assessed using standardized questionnaires. RESULTS: The exoskeleton improved both the participant's Fugl-Meyer Assessment scores and Box and Block test scores compared to not wearing the device. The subject had increased EMG activation in his extensor when wearing the exoskeleton. CONCLUSION: The inexpensive 3D printed exoskeleton was effective in assisting the participant with stroke during the functional assessments and has the potential to be used to help regain function of the hand in the home setting of an individual with stroke.IMPLICATIONS FOR REHABILITATIONA 3D printed passive hand exoskeleton may assist to accomplish rehabilitation outcomes by increasing function of the affected hand of patients with stroke.The use of this hand exoskeleton may be used to improve gross hand dexterity and assist with functional grasps during rehabilitation sessions with a lower patient's level of perceived exertion.The use of new antimicrobial 3D printing polymers can be effectively implemented to manufacture assistive devices to prevent skin infections during rehabilitation.
Authors: Alistair C McConnell; Renan C Moioli; Fabricio L Brasil; Marta Vallejo; David W Corne; Patricia A Vargas; Adam A Stokes Journal: J Rehabil Med Date: 2017-06-28 Impact factor: 2.912
Authors: S Paolucci; M G Grasso; G Antonucci; M Bragoni; E Troisi; D Morelli; P Coiro; D De Angelis; F Rizzi Journal: Arch Phys Med Rehabil Date: 2001-01 Impact factor: 3.966