Literature DB >> 28340364

Cervical facet force analysis after disc replacement versus fusion.

Vikas V Patel1, Zachary R Wuthrich2, Kirk C McGilvray3, Matthew C Lafleur1, Emily M Lindley1, Derrick Sun4, Christian M Puttlitz3.   

Abstract

BACKGROUND: Cervical total disc replacement was developed to preserve motion and reduce adjacent-level degeneration relative to fusion, yet concerns remain that total disc replacement will lead to altered facet joint loading and long-term facet joint arthrosis. This study is intended to evaluate changes in facet contact force, pressure and surface area at the treated and superior adjacent levels before and after discectomy, disc replacement, and fusion.
METHODS: Ten fresh-frozen human cadaveric cervical spines were potted from C2 to C7 with pressure sensors placed into the facet joints of C3-C4 and C4-C5 via slits in the facet capsules. Moments were applied to the specimens to produce axial rotation, lateral bending and extension. Facet contact force and pressure were measured at both levels for intact, discectomy at C4-C5, disc replacement with ProDisc-C (Synthes Spine, West Chester, Pennsylvania, USA) at C4-C5, and anterior discectomy and fusion with Cervical Spine Locking Plate (Synthes Spine, West Chester, Pennsylvania, USA) at C4-C5. Facet contact area was calculated from the force and pressure measurements. An analysis of variance was used to determine significant differences with P-values <0.05 indicating significance.
FINDINGS: Facet contact force was elevated at the treated level under extension following both discectomy and disc replacement, while facet contact pressure and area were relatively unchanged. Facet contact force and area were decreased at the treated level following fusion for all three loading conditions.
INTERPRETATION: Total disc replacement preserved facet contact force for all scenarios except extension at the treated level, highlighting the importance of the anterior disco-ligamentous complex. This could promote treated-level facet joint disease.
Copyright © 2017 Elsevier Ltd. All rights reserved.

Entities:  

Keywords:  Cervical total disc replacement; Facet contact force; Pressure; ProDisc-C; Surface area

Mesh:

Year:  2017        PMID: 28340364     DOI: 10.1016/j.clinbiomech.2017.03.007

Source DB:  PubMed          Journal:  Clin Biomech (Bristol, Avon)        ISSN: 0268-0033            Impact factor:   2.063


  5 in total

1.  Estimating Facet Joint Apposition with Specimen-Specific Computer Models of Subaxial Cervical Spine Kinematics.

Authors:  Ryan D Quarrington; Darcy W Thompson-Bagshaw; Claire F Jones
Journal:  Ann Biomed Eng       Date:  2021-11-17       Impact factor: 3.934

2.  Biomechanical Study of Cervical Disc Arthroplasty Devices Using Finite Element Modeling.

Authors:  Narayan Yoganandan; Yuvaraj Purushothaman; Hoon Choi; Jamie Baisden; Deepak Rajasekaran; Anjishnu Banerjee; Davidson Jebaseelan; Shekar Kurpad
Journal:  J Eng Sci Med Diagn Ther       Date:  2021-02-22

3.  Total disc replacement alters the biomechanics of cervical spine based on sagittal cervical alignment: A finite element study.

Authors:  Muzammil Mumtaz; Justin Mendoza; Sudharshan Tripathi; Amey Kelkar; Norihiro Nishida; Ashish Sahai; Vijay K Goel
Journal:  J Craniovertebr Junction Spine       Date:  2022-09-14

4.  The impact of different artificial disc heights during total cervical disc replacement: an in vitro biomechanical study.

Authors:  Xiao-Fei Wang; Yang Meng; Hao Liu; Bei-Yu Wang; Ying Hong
Journal:  J Orthop Surg Res       Date:  2021-01-06       Impact factor: 2.359

5.  The Effect of Axial Compression and Distraction on Cervical Facet Cartilage Apposition During Shear and Bending Motions.

Authors:  Ryan D Quarrington; Darcy W Thompson-Bagshaw; Claire F Jones
Journal:  Ann Biomed Eng       Date:  2022-03-07       Impact factor: 3.934

  5 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.