Solventless Synthesis of Poly(pyrazolyl)phenyl-methane Ligands and Thermal Transformation of Tris(3,5-dimethylpyrazol-1-yl)phenylmethane.

The solventless synthesis of tris(pyrazolyl)phenylmethane ligands of formula C₆H₅C(PzR2)₃ (R = H, Me), starting from PhCCl₃ and 3,5-dimethylpyrazole (PzMe2) or pyrazole (Pz) was performed. The sterically crowded C₆H₅C(PzMe2)₃ is thermally transformed into the bis(pyrazolyl)(p-pyrazolyl)phenylmethane ligand PzMe2-C₆H₄CH(PzMe2)₂. In this compound both PzMe2 rings are linked through the N-atom to the methine C-atom. At higher temperatures, the binding mode of PzMe2 changes from N1 to C4. All transformations occurred via quinonoid carbocation intermediates that undergo an aromatic electrophilic substitution on the 4-position of PzMe2. Reaction conditions were established to obtain five tris(pyrazolyl)phenylmethane ligands in moderate to good yields. ¹H- and 13C-NMR spectroscopy and X-ray diffraction of single crystals support the proposed structures.

1. Introduction

<span class="Chemical">Poly(pyrazolyl)methane ligands RR’C<class="Chemical">span class="Chemical">(Pz)2, RC(Pz)3 and C(Pz)4 are the neutral analogues of the anionic poly(pyrazolyl)borates [1,2,3], where Pz can be either an unsubstituted or C-substituted pyrazolyl unit. They are formally derived by replacing the apical borate anionic moiety [BR]− by the isoelectronic CR group. Trofimenko, in his pioneering work in the mid-1960s, called the poly(pyrazolyl)methane and poly(pyrazolyl)borate ligands scorpionates [4]. They are versatile hard N-donor ligands that can coordinate in a mono-, bi-, or tridentate fashion to a metal center [5]. The coordination, organometallic and related chemistry of tris(pyrazolyl)methane ligands have been reviewed elsewhere [6]. Bis(pyrazol-1-yl)methane ligands, [RR’C(Pz)2], have been used as synthetic precursors to a subclass of scorpionates called heteroscorpionates [7,8]. Their applications in the design and synthesis of metal complexes with a wide range of applications have been recently reviewed [8,9].

Steric and electronic effects modulate the chemical properties of the corresponding coordination and organo<span class="Chemical">metallic complexes of <class="Chemical">span class="Chemical">poly(pyrazol-1-yl)methane ligands. Small differences in topology, flexibility, donor properties, modes of coordination and decomposition pathways of these ligands, can lead to significantly different properties in their metal complexes.

Our investigations on <span class="Chemical">iridium organo<class="Chemical">span class="Chemical">metallic complexes formed using tris(pyrazol-1-yl)methane indicated that the steric effect exerted by this ligand strongly determines the fate of the organic moiety in the coordination sphere of the metal as well as the energetics of the olefinic C-H bond activation reactions [10,11,12].

The chemistry of <span class="Chemical">poly(pyrazolyl)methanes has been relatively underdeveloped. However, this family of ligands can act as more than a simple class="Chemical">spectator in the course of the chemical r<class="Chemical">span class="Chemical">eactions due to the possibility of temporary changes in denticity and its ambidentate nature after the removal of the bridge CH proton [13]. Furthermore, the significant number of examples confirm that the properties and reactivity of the corresponding metal complexes differ from that of the tris(pyrazol-1-yl)borate analogues.

More recently, the use of <span class="Chemical">poly(pyrazolyl)methanes in supramole<class="Chemical">span class="Chemical">cular chemistry has become more frequent. Bis(pyrazol-1-yl)(pyridin-x-yl)methane ligands give rise to a rich variety of complexes and supramolecular frameworks with a wide range of transition metals [14]. The crowded tris(pyrazolyl)methane chelate in a macrobicyclic structure was synthesized in order to create a cavity with well-defined dimensions and shape [15]. Also, aryl-o-substituted-bis(pyrazol-1-yl)methanes (RSPhCH(PzMe2)2) have been synthesized to give rise to supramolecular microporous structures such as coordination polymers and macrocycles [16]. Other areas of development are catalysis, bioinorganic and biologically inspired chemistry [17]. In this field, the chemistry of Re and Tc complexes anchored by tris(pyrazolyl)methanes have potential relevance in the field of biomedical applications, particularly in radiopharmaceutical research [18].

In general, <span class="Chemical">poly(pyrazolyl)methanes CH2<class="Chemical">span class="Chemical">(Pz)2, CH(Pz)3 and C(Pz)4 have been prepared by treating the pyrazolate salt with CH2Cl2, CHCl3 or CCl4 in the presence of phase transfer catalysts. This technique has been particularly exploited to prepare tris(pyrazol-1-yl)methanes of formula HC(PzR)3 (R = 3,5-Me, 3-Ph, 3-Pr, 3-Bu, 3,5-Pr) [19,20,21,22]. The metal catalyzed condensation of (Pz)2E = O (E = C, S) with aldehydes or ketones provides an efficient route to unsymmetrical tris(pyrazol-1-yl)methane ligands. However, similar chemistry is unsuccessful with substituted pyrazolyl rings [23]. The preparation of “mixed” tris(pyrazolyl)methanes with two or three different pyrazolyl rings (HCPzR(PzR′)2 or HCPzRPzR′PzR″) has been achieved by the scrambling of tris(3,5-dimethylpyrazolyl)methane with substituted pyrazoles in acid media [24]. More recently, a third generation of scorpionates with a substituted-aryl ring bound to the carbon bridge of tris(pyrazol-1-yl)methane, has been synthesized starting from trifluoromethylaniline [25]. Methods for synthesizing bis and tris(pyrazol-1-yl)methanes have been recently reviewed [26].

In an effort to contribute to the design of a new and improved synthesis of class="Chemical">poly(pyrazol-1-yl)methane ligands, we decided to explore the synthesis without solvent (solventless synthesis) of <class="Chemical">span class="Chemical">tris(3,5-dimethylpyrazol-1-yl)phenylmethane (1a) and tris(pyrazol-1-yl) phenylmethane (1b), starting from α,α′,α″-trichlorotoluene (PhCCl3) and 3,5-dimethylpyrazole (PzMe2) or pyrazole (Pz), (Figure 1). In this sense, thermal treatment [27] as well as sonochemical methods [28], mechanochemistry [29], microwave [30] and infrared [31] irradiation have been used for chemical synthesis driven by the search for new and cleaner synthetic methodologies. To the best of our knowledge, the sterically crowded compounds 1a and 1b have never been described before, whereas PhCCl3 has been scarcely used in spite of its similarity to CHCl3. It has been reported as the starting material for the synthesis of the hexadentate N6-donor phenyltris[3-(2-pyridyl)pyrazol-1-yl]methane [32].

Figure 1

Target compounds C6H5C(PzMe2)3 (1a) and C6H5C(Pz)3 (1b).

2. Results and Discussion

2.1. Screening Reactions with PzMe2

Since the r<span class="Chemical">eaction of <class="Chemical">span class="Chemical">pyrazoles with PhCCl3 has been reported to occur in low yields [32], we decided to explore the heating of 3,5-dimethylpyrazole (PzMe2) without solvent while varying several different reaction conditions such as temperature, time, stoichiometry and the reaction atmosphere. Results are listed in Table 1 by numbered entries as yields of the isolated products after column chromatography. Initially, the reaction was performed in an open flask equipped with a condenser, the PzMe2 to PhCCl3 ratio was chosen as 6:1, the excess of PzMe2 was used to trap the evolved HCl, the mixture was melted (100 °C) and stirred for 10 h. A stronger base than PzMe2 was not used to trap the evolved HCl in order to prevent the production of 1,1,2,2-tetrachloro-1,2-diphenylethane as side-product [33]. In the above conditions, compounds 2, 5 and 6 were isolated in low yields from the reaction mixture (entry 1) and sublimated PzMe2 was observed on the top of the flask (Scheme 1).

Table 1

Reaction conditions of heating 3,5-dimethylpyrazol with α,α′,α″-trichlorotoluene.

Entry	Vessel	Ratio 1	Temperature (°C)/Time (h)		Products Isolated Yields (%)
			Step 1	Step 2	1a	2	3	4	5	6
1	Open flask	6:1	100/10	none	---	11	---	---	6	10
2	SA 2	6:1	120/24	none	---	---	---	8	Trace	Trace
3	SA	6:1	80/48	none	---	---	---	---	7	Trace
4	SA	6:1	80/24	120/24	---	53	27	---	6	Trace
5	SA	8:1	80/24	120/24	---	48	25	---	8	Trace
6	SA	4:1	80/24	120/24	---	27	7	---	9	Trace
7	VSA 3	6:1	80/24	none	15	---	---	---	---	---
8	VSA	6:1	80/48	none	30	---	---	---	---	---
9	VSA	6:1	80/48	120/24	---	70	2	---	---	Trace
10	VSA	6:1	160/72		---	---	---	14	---	---

1 PzMe2 to PhCCl3; 2 Sealed ampoule; 3 Vacuum sealed ampoule.

Scheme 1

Thermal reaction of 3,5-dimethylpyrazol (PzMe2) with α,α′,α″-trichlorotoluene (PhCCl3).

In order to avoid the sublimation of <span class="Chemical">PzMe2 and to improve yields, we used a s<class="Chemical">span class="Chemical">ealed glass ampoule instead of a flask. The same quantities of reagents were used and heated at 120 °C for 24 h. In this case, the new product 4 was isolated in low yield (entry 2). The same reaction carried out at 80 °C for 48 h, leads to only small amounts of compound 5 (entry 3). These results suggest the transformation of the target compound 1a into compounds 2 and 4. However, as compound 1a was not present in any of the last conditions, we carried out the reaction in two steps, the first at 80 °C and the second at 120 °C for 24 h each. In this case compounds 2 (53%) and the new compound 3 (27%) appeared as principal products (entry 4). We tried the same reaction lowering the initial reaction time to 24 h and the PzMe2 to PhCCl3 ratio in 8:1 and 4:1 proportions, but the yields of compounds 2 and 3 were lower (entries 5 and 6, respectively). In all cases, compounds 5 and 6 appeared as oxidation products in the reaction mixture.

To avoid the formation of the oxidation products 5 and 6, the r<span class="Chemical">eaction was carried out in a one-step r<class="Chemical">span class="Chemical">eaction, with a 6:1 ratio of reactants, at 80 °C for 24 h in a sealed ampoule under vacuum. In this case, compound 1a was obtained as the only product in 15% yield (entry 7). The best results to obtain compound 1a in 30% yield were when the reaction was performed in the same reaction conditions but increasing the reaction time to 48 h (entry 8). Compound 2 was isolated in 70% yield in the two steps of temperature conditions at 80 °C and 120 °C for 48 h and 24 h, respectively (entry 9). Finally, compound 4 was isolated in 14% yield increasing the temperature to 160 °C for 72 h (entry 10).

It is worth mentioning that, to the best of our knowledge, compounds 1a–4 have not been reported before, compound 5 was reported in 1935 [34] and compound 6 is not known but the <span class="Chemical">pyrazole analogue of 6 has been reported elsewhere [35].

2.2. Effect of Temperature and Time on the Composition of the Reaction Mixtures

In order to find the appropriate temperature that would favor one of the ligands 1a–4, three r<span class="Chemical">eactions were performed using two temperature steps. The first step was fixed at 80 °C and the second at 100, 120 or 160 °C for 24 h <class="Chemical">span class="Chemical">each. In all cases, the reaction at 80 °C for 24 h was used as reference with 30% composition of compound 1a. The composition of the reaction mixtures was quantified by HPLC and the results are summarized in Table 2. These experiments and those summarized in Table 3 were performed at a smaller scale (1/5) than the screening experiments summarized in Table 1; thus differences in the composition of the reaction mixtures are explained because of mass dependent conductive/convective heat transfer processes.

Table 2

Composition of the reaction mixture (%) after two heating steps at three temperatures.

Comp.	80 °C to T2 (°C)
	100	120	160
1a	26	18	0
2	11	55	0
3	0	12	0
4	0	0	11

Table 3

Composition of the reaction mixture (%) after heating at 120 °C.

Comp.	Heating Time (Days)
	1	2	3
1a	13	8	0
2	7	0	0
3	5	3	0
4	23	35	40

From the above results, it can be concluded that compounds 2 and 3 are formed at 100 and 120 °C, respectively, at the expense of compound 1a. Compound 4 remained at 160 °C as the only product in low quantity. These results suggest that compound 1a is successively transformed into compounds 2–4 with the incrclass="Chemical">ease in the temperature of r<class="Chemical">span class="Chemical">eaction, accompanied by extensive decomposition at 160 °C. As expected, compounds 1a and 2, with C-N bonds, are produced at lower temperatures; on the contrary, compounds 3 and 4, with C-C bonds, are favored at higher temperatures.

In an independent experiment, the temperature was fixed at 120 °C but the course of the r<span class="Chemical">eaction was monitored by HPLC for three days. The daily percent composition of the r<class="Chemical">span class="Chemical">eaction mixture is listed in Table 3. A mixture of compounds 1a–4 was found the first day of reaction at 120 °C. In the next two days, the composition of the mixture showed an increase in compound 4 with the corresponding decrement of compounds 1a–3. These results confirm that once formed, compounds 1–3 are consecutively transformed into compound 4.

Compounds 2–4 contain a built-in entry point for further functionalization, and they could be used as monomers for new class="Chemical">polyamines or ligands for the synthesis of MOF’s [36]. In addition, both <class="Chemical">span class="Chemical">nitrogen atoms of each pyrazole ring in compound 4 are available for further coordination. Suzuki coupling methodology starting from 1-trityl-1H-pyrazol-4-ylboronate pinacol esters and brominated aromatic precursors has been used to achieve this structural feature in the synthesis of oligo-(1H-pyrazol-4-yl)-arenes [37].

2.3. Reaction between PhCCl3 and Pz

The r<span class="Chemical">eaction of <class="Chemical">span class="Chemical">pyrazole and PhCCl3 was performed using the reaction conditions described in entry 9 of Table 1. In these conditions, tris(pyrazolyl)phenylmethane 1b was isolated in 50% yield as the only product, Scheme 2. Due to the absence of more products, no other reaction conditions were tested.

Scheme 2

Thermal reaction of pyrazole with α,α′,α″-trichlorotoluene.

2.4. Stucture by NMR and IR

Compounds 1a and 1b possess C3 symmetry in agreement with three <span class="Chemical">pyrazole rings bonded to the bridge <class="Chemical">span class="Chemical">carbon atom of the former PhCCl3. This was confirmed by the 1H-NMR spectrum of 1a that shows two signals for each of methyl groups (δ 2.18, 1.62). One of them appears shielded by 0.4 ppm compared with that of (PzMe2)CH (δ 2.09, 2.03) [21]. The CH of three PzMe2 rings appeared at δ 5.95. Compound 1b shows the signals for Pz-ring protons at δ 7.73 (d), 7.52 (d) and 6.36 (t). The typical 1:2:2 pattern for a monosubstituted benzene ring is present in the 1H-NMR spectra of both compounds. Finally, the bridge carbon atom is at δ 94.3 and 94.4 in 13C-NMR for 1a and 1b, respectively.

The 1H-NMR spectrum of compound 2 shows two sets of signals at δ 2.28, 2.27 and 2.26, 2.20 ppm in a 2:1 proportion corresponding to the methyl groups of the class="Chemical">PzMe2 rings. Two <class="Chemical">span class="Chemical">pyrazole CH are at δ 5.86 and 5.98 ppm in agreement with a molecule with C2v symmetry. The methine proton and carbon atoms appear as a singlet at δ 7.65 (1H) and δ 73.5 (13C), very similar to those values reported for (PzMe2)2CHPh [26]. In addition, the presence of signals at δ 7.40 and 6.98, as doublets, are in agreement with the typical pattern for a p-substituted benzene ring. They were assigned to the m- and o-protons, respectively, by NOE effect when irradiating the bridge methine CH. This pattern is also observed for compounds 3 and 4 with similar chemical shifts.

The symmetry is lost in compound 3 because the <span class="Chemical">PzMe2 rings are bonded differently to the bridge <class="Chemical">span class="Chemical">methine carbon atom. The C-N bonded PzMe2 ring, shows signals at δ 5.86 and 105.8 for H4 and C4, respectively. No signal corresponding to H4 was observed and C4 of PzMe2 ring appeared at δ 113.6 as singlet in the 13C{1H} NMR spectrum of the C-C bonded ring. In addition, a broad singlet at δ 144.0, corresponding to the CMe carbon atom of the two tautomers in equilibrium, was observed; the respective NH appeared at δ 7.60. Also, a singlet appeared for each remaining four methyl carbon atoms. It is worth noting that the chemical shifts of the methine proton and carbon atoms are at δ 6.45 and 57.0, respectively a value in the middle of the corresponding values for compounds 2 and 4.

In compound 4, both <span class="Chemical">PzMe2 rings are linked by a C-C bond to the bridge <class="Chemical">span class="Chemical">methine carbon atom. Some relevant changes in both the 1H- and 13C-NMR spectra are appreciated in agreement with its C2v symmetry. The CH of the pyrazole ring is absent in the 1H-NMR spectrum, a broad signal at δ 12 for the NH proton appears instead, as well as a singlet at δ 115.7 in the 13C{1H} NMR spectrum, corresponding to C4 of both PzMe2 rings. Tautomeric equilibrium, typical of NH pyrazole heterocycles, is present leading to a broad signal for both CMe carbon atoms of each PzMe2 at δ 142.7. Finally, the bridge methine proton and carbon atoms are shifted to high fields (δ 5.3, 39.3).

The 1H-NMR spectrum of compound 5 shows the characteristics set of signals corresponding to a monosubstituted class="Chemical">benzene ring as well as a singlet at δ 6.06 and two signals in δ 2.63 and 2.25 for two methyl groups of the <class="Chemical">span class="Chemical">PzMe2 ring. The signal at δ 168.7 in the 13C-NMR spectrum was assigned to a C=O group which was confirmed by the presence of an IR stretching band at 1694 cm−1. These spectroscopic data are in agreement with an amide group. The NMR of compound 6 shows the characteristic signal for an aldehyde: a singlet at δ 10.04 in the 1H-NMR spectrum, and at δ 191.4 in the 13C-NMR one. The stretching frequency at 1697 cm−1 confirmed the presence of the C=O group. The signals in the 1H-NMR spectrum are consistent with the presence of a p-substituted benzene ring at δ 7.97 and 7.67 and, three singlets at δ 6.06, 2.41 and 2.31 for the PzMe2 ring.

2.5. Proposed Reaction Mechanism

Based on the above results a mechanistic pathway is proposed for the h<span class="Chemical">eating r<class="Chemical">span class="Chemical">eaction of PzMe2 and PhCCl3. A nucleophilic attack of two PzMe2 molecules to carbocation PhCCl2+ formed from PhCCl3, give the intermediate carbocation I. The fate of carbocation I depends on temperature, at 80 °C, the attack of the third PzMe2 leads to compound 1a (Scheme 3, path A). Compound 1a reversibly releases one pyrazole ring to regenerate carbocation I when temperature is increased to 100 °C. Then, compound 2 is obtained by the attack of the third PzMe2 to the resonance quinonoid aryl carbocation intermediate II (Scheme 3, path B) loosing of one proton to recover the aromatic form. The intrinsic instability of compound 1a could be attributed to the steric repulsion exerted by both phenyl and methyl groups, which favors the breaking of the bridge C-N bond to liberate the steric constraint. α-chlorobenzyl cations have been reported as intermediates in reactions of hydrolysis [38] whereas radicals or cation radicals are produced only when initiators are added [39].

Scheme 3

Proposed mechanistic pathway for the reaction of PzMe2 and PhCCl3.

The synergy of both steric and electronic effects is evident in the rclass="Chemical">eaction of the unsubstituted <class="Chemical">span class="Chemical">pyrazole (Pz) and PhCCl3 that produce the stabile compound 1b as the only product. No decomposition or transformation of 1b was observed at the temperature of 120 °C. Pyrazole is non-steric constrained and less basic than PzMe2 (pKa values are 2.85 and 14.2 for Pz, 4.28 and 15.1 for PzMe2) [40,41]. Compounds 3 and 4 are produced from compound 2. Their formation implies the substitution of N-bonded PzMe2 by C-bonded PzMe2. At 120 °C, compound 2 irreversibly releases one protonated pyrazole ring. This step requires the participation of an electron donating group in the aryl ring to weaken the C-N bond via the formation of the quinonoid carbocation intermediate III, which is stabilized by resonance. The intermediate resonance hybrid form IV performs an aromatic electrophilic substitution (AES) on the 4-position of PzMe2 to form compound 3. The subsequent elimination-substitution of the second pyrazole leads to the formation of compound 4 (Scheme 4). The activating role of the electron donating group in the aryl ring have been demonstrated to be necessary in an elimination-addition mechanism that provides access to tris(pyrazolyl)-toluidines [25]. On the other hand, AES reaction in PzMe2 is reported to occur under mild conditions [42].

Scheme 4

Proposed mechanistic transformation of compound 2 to 3 and 4.

2.6. Single Crystal Structures of – and

The structures of compounds 1a and 1b were unambiguously confirmed by single-crystal X-ray diffraction analysis. Suitable crystals of compound 1a were obtained from <span class="Chemical">hexane solution. Compound 1a crystallized in the monoclinic system with a class="Chemical">space group <class="Chemical">span class="Gene">P21/c. The molecular structure is displayed in Figure 2.

Figure 2

ORTEP perspective of compound 1a at 30% probability level, hydrogen atoms are omitted for clarity. Selected bonds lengths (Å) and angles (°): N10-C1 1.4657(19), N20-C1 1.4725(18), N30-C1 1.479(2), C1-C2 1.532(2), N30-C1-C2 111.47(11), N20-C1-C2 107.84(11), N30-C1-C2 111.75(11), N10-C1-N20 109.86(11), N10-C1-N30 106.48(12), N20-C1-N30 109.43(11), N11-N10-C1 119.04(11), N21-N20-C1 118.72(11), N31-N30-C1 119.76(11).

The geometry around the C1 bridge <span class="Chemical">carbon atom is n<class="Chemical">span class="Chemical">early tetrahedral with an average N-C-N bond angles of 109(2)° and the N-C-CPh angle of 110(2)°. The mean C-N and C-CPh bond distances of 1.477(7) Å and 1.532(2) Å, respectively, are in close correspondence with single bonds (1.493(20), 1.513(14) Å) [43]. The three PzMe2 rings adopt a three-bladed propeller structure around the axial phenyl with R3-C-N-N torsion angles of ±8.97(17)°, ±101.46(15)° and ±141.34(13)°. Thus, racemic helical molecules of 1a are found to exist as both left-(Λ) and right-handed (Δ)-enantiomers in the asymmetric unit of the crystal lattice. Among several possible conformers, compound 1a adopts a sp, ac, ac conformation (synperiplanar (sp), synclinal (sc), antiperiplanar (ap) and anticlinal (ac)).

Suitable crystals of compound 1b were obtained from a saturated solution in AcOEt. Crystals of 1b crystallize in the orthorhombic system in the acentric P2 space group. The moleclass="Chemical">cular structure is diclass="Chemical">splayed in Figure 3. Bond distances and angles are very similar to those found in compound 1a (average values): N-<class="Chemical">span class="Chemical">C-N bond angle of 110(2)°, N-C-CPh angle of 111(2)° and C-N and C-CPh bond distances of 1.476(16) Å and 1.525(5) Å, respectively. Three blades are formed by Pz rings; the values of the R3-C-N-N torsion angles are ±87.17(4)° (sc), ±104.2(4)° (ac) and ±166.6(4)° (ap).

Figure 3

ORTEP perspective of compound 1b at 25% probability level; hydrogen atoms are omitted for clarity. Selected bonds lengths (Å) and angles (°): N10-C1 1.472(5), N20-C1 1.452(5), N30-C1 1.477(5), C1-C2 1.525(6), N30-C1-C2 111.8(3), N10-C1-N20 109.9(3), N10-C1-N30 107.8(3), N11-N10-C1 119.1(3), N21-N20-C1 120.8(4), N31-N30-C1 126.2(4)

Since the structures of several ligands 7–15, similar to compounds 1a and 1b, have been reported [24,25,44,45,46,47,48,49,50], a brief comparison between them seems to be appropriate. The structures, R3-<span class="Chemical">C-N-N torsion angles values and the conformation of <class="Chemical">span class="Chemical">pyrazole rings in compounds 1a,b and 7–15 are listed in Table 4.

Table 4

Torsion angles and conformation of three bladed propeller structures of general formula (PzR1R2)3CR3.

Comp.	Substituents	Torsion Angle (°) R3CNN	PzR1R2 Conformation 1
1a	R1 = R2 = CH3, R3 = C6H5	−8.97(17), 101.46(15), 141.34(13)	sp, ac, ac
7 [44]	R1 = CH3, R2 = C6H5, R3 = H	−18.3, 133.4, 148.6	sp, ac, ac
8 2 [45,46]	R1 = R2 = CH3, R3 = H	(±)25(5), (±)116(5), (±)152(5)	sp, ac, ap
1b	R1 = R2 = H, R3 = C6H5	−87.2(4), −104.2(4), −166.6(4)	sc, ac, ap
9 [25]	R1 = R2 = H, R3 = o-C6H4-NH2	29.89(13), 87.54(11), 179.85(9)	sp, sc, ap
10 [25]	R1 = R2 = H, R3 = p-C6H4-NH2	−25(11), −83(14), 173(7)	sp, sc, ap
11 [47]	R1 = R2 = H, R3 = p-C6H4-C6O2S	42.6(7), 73.6(8), 166.4(2)	sc, sc, ap
12 [48]	R1 = R2 = H, R3 = p-C6H4OH	−45.02(14), −68.86(14), 173.04(14)	sc, sc, ap
13 [49]	R1 = R2 = H, R3 = CH2OH	−34.49(13), −62.50(12), 174.56(9)	sc, sc, ap
14 [24]	R1 = H, R2 = CH3, R3 = H	24.48, 27.97, 170.87	sp, sp, ap
15 [50]	R1 = R2 = R3 = H	13.6, 15.7, 176.0	sp, sp, ap

1 Torsion angle from 0° to ±30° is called synperiplanar (sp), ±30° to ±90° synclinal (sc), ±90° to ±150° anticlinal (ac) and ±150° to ±180° antiperiplanar (ap). 2 Average value of two molecules in the asymmetric unit.

All these mole<span class="Chemical">cules are very similar; their bond distances and angles have no evident differences regardless of the steric demand from the substituents in the <class="Chemical">span class="Chemical">pyrazole ring or in the apical carbon atom. However, steric effects seem to determine the conformation adopted by pyrazole rings in the three-bladed propeller structure. Compounds 1a and 7, the most crowded, are in such disposition that one pyrazole is in sp and the other two are in ac conformations (sp + 2ac). As long as steric demand is diminished, one ring adopts an ap conformation and the other two are concomitantly twisted to finally adopt the sp conformation (2sp + ap) in the less crowded compounds 14 and 15. As expected, substituents in the pyrazole rings exert more steric demand than those located in the apical carbon atom.

Compound 2 crystalized with 0.5 mole<span class="Chemical">cules of <class="Chemical">span class="Chemical">water in the asymmetric unit as a monoclinic system with a space group C2/c. The crystal structure is shown in Figure 4. Bond distances and angles are very similar to those found in compound 1a (average values): N-C-N bond angle of 111.5(3)°, N-C-CPh angle of 113.3(4)° and C-N and C-CPh bond distances of 1.455(7) Å and 1.521(5) Å, respectively. Two blades are formed by PzMe2 rings, the values of the R3-C-N-N torsion angles are −105.0(3)° and −29.2(5)° corresponding to ac, sp conformation, respectively.

Figure 4

ORTEP perspective of compound 2 at 25% probability level, hydrogen atoms and the molecule of water are omitted for clarity. Selected bonds lengths (Å) and angles (°): N10-C1 1.464(5), N20-C1 1.445(5), C1-C2 1.521(5), N10-C1-C2 112.5(3), N20-C1-C2 114.1(3), N10-C1-N20 111.5(3), N11-N10-C1 116.7(3), N21-N20-C1 121.4(3).

Two mole<span class="Chemical">cules of 2 are <class="Chemical">span class="Chemical">hydrogen bonded to one molecule of water. One of them forms a pseudo six membered ring R22(6) [51] through strong O-H∙∙∙N interactions, with the participation of pyrazole N atom as the acceptor and by soft C(sp3)-H∙∙∙O interactions. The other molecule of 2 is linked to the oxygen atom of the water molecule by pyrazole C4-H as donor (Figure 5). This supramolecular arrangement highlights the acid-base sites in the molecule, in agreement with the proposed mechanism of transformation of compound 2 into compounds 3 and 4 (vide supra).

Figure 5

Supramolecular structure of compound 2. Geometry of hydrogen bonding: H1A∙∙∙N11 = 1.96(6) Å, O1∙∙∙N11 = 2.925(4) Å, O1-H1A∙∙∙N11 = 156(6)° and H1∙∙∙O1 = 2.51 Å, C1∙∙∙O1 = 3.441(6) Å, C1-H1∙∙∙O1 = 137° (symmetry code = −1/2 + x, ½ + y, z); H33∙∙∙O1 = 2.51 Å, C33∙∙∙O1 = 3.410(6) Å, C33-H33∙∙∙O1 = 158° (symmetry code = x, −1 + y, z).

3. Materials and Methods

3.1. Chemicals

<span class="Chemical">Pyrazole, <class="Chemical">span class="Chemical">3,5-dimethylpyrazole, α,α′,α″-trichlorotoluene and solvents were reagent grade and used as received.

3.2. Instrumental Methods

Melting points were m<span class="Chemical">easured on an IA 9100 apparatus (Electrothermal, Staffordshire, UK) and are uncorrected. IR class="Chemical">spectra were recorded using a 3100 FT-IR Excalibur Series class="Chemical">spectrophotometer (Varian, Randolph, MA, USA) equipped with an ATR system. Mass class="Chemical">spectra were obtained in a 3900-GC/MS system (Varian, Palo Alto, CA, USA) with an electron <class="Chemical">span class="Disease">ionization mode. Elemental analyses (EA) were performed on a 2400 elemental analyzer (Perkin-Elmer, Waltham MA, USA). 1H- and 13C-NMR spectra were recorded on a Varian Mercury 300 (1H, 300.08; 13C, 75.46 MHz) instrument in CDCl3 solutions for compounds 1–6, and in DMSO-d6 solutions for compound 7, SiMe4 as the internal reference was used. Chemical shifts are in ppm and (H-H) in hertz. The chemical shift assignments were performed on the basis of 1H- and 13C-NMR NOE, COSY and HETCOR experiments. Composition of the reaction mixtures were performed in a Varian 9010 HPLC instrument at 252 nm. A C18 column of 5 μm particle size and 25 cm length and 0.5 cm wide was used. Elution was achieved with MeOH/H2O mixtures in a 7:3 proportion, unless otherwise specified.

3.3. X-ray Diffraction Methods

Single-crystal X-ray diffraction data of mole<span class="Chemical">cules 1a, 1b and 2 were recorded on a D8 Quest CMOS (Bruker, Karlsruhe, Germany) or Nonius Kappa (Rotterdam, The Netherlands) ar<class="Chemical">span class="Chemical">ea detector diffractometers with Mo K α radiation, λ = 0.71073 Å. A table listing the crystallographic data is provided as Supplementary Material. The structures were solved by direct methods using SHELXS97 [52] program of WinGX package [53]. The final refinement was performed by full-matrix least-squares methods on F2 with SHELXL97 [52] program. H atoms on C were geometrically positioned and treated as riding atoms, with C-H = 0.93–0.98 Å, and with Uiso(H) = 1.2Ueq(C). The hydrogen atoms of the water molecule were found by Fourier difference and freely refined. The program Mercury was used for visualization, molecular graphics and analysis of crystal structures [54]. The software used to prepare material for publication was PLATON [55]. Crystallographic data for the structures in this paper have been deposited with the Cambridge Crystallographic Data Centre as supplementary publication CCDC numbers 1527853 (1a), 1527852 (1b) and 1527854 (2). Copies of the data can be obtained free of charge on application to CCDC, 12 Union Road, Cambridge CB2 1EZ, UK, (Fax: +44-01223-336033 or E-Mail: deposit@ccdc.cam.ac.uk). Crystals suitable for X-ray analysis were obtained from the saturated hexane solution of compound 1a and from DMSO-H2O solution (1:1) of compound 1b. Compound 2 slowly crystalized with one molecule of water in the asymmetric unit from the semi-solid remaining after solvent evaporation.

Crystal Data for C (1a, M = 374.5 g/mol): monoclinic, space group <span class="Gene">P21/c (No. 14), a = 10.0680(3) Å, b = 14.6640(3) Å, c = 15.3674(5) Å, β = 114.204(3)°, V = 2069.35(31) Å3, Z = 4, T = 298(2) K, Dcalc = 1.200 g/cm3, 23332 reflections m<class="Chemical">span class="Chemical">easured (3.4° ≤ 2Θ ≤ 27.5°), 4632 unique (Rint = 0.046, Rsigma = 0.048) which were used in all calculations. The final R1 was 0.053 (I > 2σ(I)) and wR2 was 0.125 (all data).

Crystal Data for C (1b, M = 290.33 g/mol): orthorhombic, space group P212121 (No. 19), a = 7.0198(8) Å, b = 14.2693(16) Å, c = 14.6994(17) Å, α = β = γ = 90°, V = 1449.37(3) Å3, Z = 4, T = 293(2) K, Dcalc = 1.331 g/cm3, 8182 reflections m<span class="Chemical">easured (2.0° ≤ 2Θ ≤ 24.0°), 2280 unique (Rint = 0.08, Rsigma = 0.139) which were used in all cal<class="Chemical">span class="Chemical">culations. The final R1 was 0.055 (I > 2σ(I)) and wR2 was 0.1203 (all data).

Crystal Data for C22H26N6∙0.5H (2, M = 383.49 g/mol): monoclinic, space group C 2/c (No. 15), a = 20.9571(15) Å, b = 9.5425(6) Å, c = 21.8515(16) Å, β = 103.528(2)°, V = 4248.69(22) Å3, Z = 4, T = 100(2) K, Dcalc = 1.200 g/cm3, 19257 reflections m<span class="Chemical">easured (2.4° ≤ 2Θ ≤ 25.0°), 3584 unique (Rint = 0.043, Rsigma = 0.0351) which were used in all cal<class="Chemical">span class="Chemical">culations. The final R1 was 0.089 (I > 2σ(I)) and wR2 was 0.188 (all data).

3.4. Synthetic Procedures

3.4.1. Open Flask Procedure

<span class="Chemical">3,5-Dimethylpyrazole (<class="Chemical">span class="Chemical">PzMe2, 5.00 g, 52.0 mmol) was placed in a round bottom flask, submerged in a silicon oil bath and heated at 110 °C with constant stirring. When the pyrazole was molten, α,α′,α″-trichlorotoluene (PhCCl3, 246 µL) was added dropwise every hour until complete 1.230 mL (8.660 mmol) had been added. Heating was maintained for 5 h to obtain a yellow viscous liquid. The products were purified by column chromatography on silica gel using a 6:4 mixture of hexane/EtOAc as eluent (Table 1, entry 1).

3.4.2. Sealed Ampoule Procedure

<span class="Chemical">PzMe2 (5.00 g, 52.0 mmol) was ground in a mortar and placed into a 10 mL glass ampoule with <class="Chemical">span class="Chemical">PhCCl3 (0.93 mL for 8:1; 1.23 mL for 6:1 or 1.85 mL for 4:1 ratio). The ampoules were sealed at room temperature, introduced into a convection oven and allowed to react at the temperature and time indicated in Table 1. The obtained viscous brown colored mixtures were dissolved in 50 mL of CHCl3 to remove them from the ampoules and subjected to column chromatography on silica gel. Compounds 1–3 and 5–6 were purified using hexane/EtOAc mixtures from 8:2 to 6:4 proportions as eluents.

3.4.3. Vacuum Sealed Ampoule Procedure

<span class="Chemical">PzMe2 (5.00 g, 52.0 mmol) was ground in a mortar and placed into a 10 mL glass ampoule with <class="Chemical">span class="Chemical">PhCCl3 (1.23 mL, 8.66 mmol, 6:1). The ampoules were frozen at −30 °C, sealed under vacuum and then introduced into a convection oven and allowed to react at the temperature and time indicated in Table 1. The reaction mixtures were treated as indicated in Section 3.4.2.

3.5. Synthesis of Compounds –

1,1′,1″-(Phenylmethanetriyl)tris(<span class="Chemical">3,5-dimethyl-1H-pyrazole) (. This compound was synthesized following the procedure described in Section 3.4.3 h<class="Chemical">span class="Chemical">eating at 80 °C for 24 h (Table 1, entry 8) to obtain 0.975 g (2.60 mmol, 30% yield) of a white crystalline solid m.p. = 90 °C after column chromatography. 1H-NMR (CDCl3): δ 7.39 (t, 1H, = 6.9, H-10), 7.32 (t, 2H, = 7.0, H-9), 7.02 (d, 2H, = 7.0, H-8), 5.95 (s, 3H, H-4), 2.18, 1.62 (s, 9H each, 6CH3). 13C-NMR (CDCl3): δ 146.9 (C-3), 143.9 (C-5), 138.1 (C-7), 130.5 (C-8), 129.6 (C-9), 127.3 (C-10), 109.1 (C-4), 94.3 (C-6), 14.3, 12.9 (CH3). IR neat (cm−1): 1697 (C=C), 1562 (Car), 1450, 1411, 1374, 1316, 1027, 890, 716. EA % found [calculated for C22H26N6 (374.49 g·mol−1)]: 70.06 (70.56, C), 7.11 (7.00, H), 22.01 (22.40, N).

1,1′,1″-(Phenylmethanetriyl)tris(<span class="Chemical">1H-pyrazole) (. A crystalline solid m.p. = 105 °C was obtained (1.95 g, 55% yield), starting from 4.97 g (17.16 mmol) of <class="Chemical">span class="Chemical">pyrazole and 1.7 mL (12.2 mmol) of PhCCl3. Procedure 3.4.3 was followed using two temperature steps: 80 °C and 120 °C for 48 and 24 h each, respectively (Table 1, entry 9). The crude product was solubilized in EtOAct and filtered, whereupon compound 1b crystallized from the solution. 1H-NMR (CDCl3): 7.73 (d, 3H, H-3), 7.52 (d, 3H, = 2.6, H-5), 7.48 (t, 1H, = 7, H-10), 7.41 (t, 2H, = 8.7, H-9), 7.09 (d, 2H, = 8, H-8), 6.36 (t, 3H, = 2.6, 1.7, H-4). 13C-NMR (CDCl3): 141.6 (C-3), 137.6 (C-7), 132.6 (C-5), 130.8 (C-10), 128.9 (C-9), 128.5 (C-8), 106.7 (C-4), 93.4 (C-6). IR (neat, ν/cm−1): 1682 (C=N), 1451, 1419, 1388, 1196, 1095, 1087, 864, 746 (Pz out of plane). EA % found [calculated for C16H14N6 (290.32 g·mol−1)]: 66.16 (66.19, C), 4.91 (4.86, H), 28.91 (28.95, N).

1,1′-((4-(3,5-Dimethyl-1H-pyrazol-1-yl)phenyl)m<span class="Chemical">ethylene)bis(<class="Chemical">span class="Chemical">3,5-dimethyl-1H-pyrazole) (. Synthesized following the procedure described in Section 3.4.3 using two temperature steps at 80 °C and 120 °C for 48 and 24 h each, respectively (Table 1, entry 9). After column chromatography, 2.28 g (6.09 mmol, 70% yield) of compound 2 as a viscous yellow liquid which slowly solidified after standing as a yellow solid m.p. = 97 °C was obtained. 1H-NMR: δ 7.65 (s, 1H, H-6), 7.40 (d, 2H, = 8.8, H-9), 6.98 (d, 2H, = 8.8, H-8), 5.98 (s, 1H, H-14), 5.86 (s, 2H, H-4), 2.28, 2.27 (s, 6H each, 4CH3), 2.26, 2.20 (s, 3H each, 2CH3). 13C-NMR: δ 149.5 (C-13), 148.8 (2C-3), 141.3 (2C-5), 140.1 (C-15), 139.7 (C-10), 135.8 (C-7), 127.9 (2C-8), 124.6 (2C-9), 107.5 (C-14), 107.2 (2C-4), 73.5 (C-6), 13.9, 13.0 (4CH3), 13.7, 12.7 (2CH3). IR (neat, ν/cm−1): 1612 (C=N), 1556 (C=C), 1520 (Car), 1417 (CH3), 750 (pyrazole out of plane). MS (%): 374.0 (M+, 3), 279.0 (100), 183.9 (5), 162.0 (26), 94.8 (12.5). EA % found [calculated for C22H26N6 (374.48 g·mol−1)]: 70.50 (70.56, C), 7.17 (7.00, H), 21.70 (22.44, N).

1,4′-((4-(3,5-Dimethyl-1H-pyrazol-1-yl)phenyl)m<span class="Chemical">ethylene)bis(<class="Chemical">span class="Chemical">3,5-dimethyl-1H-pyrazole) (. Synthesized following the procedure described in Section 3.4.2 using two temperature steps of 80 °C and 120 °C for 24 h each (Table 1, entry 4) to obtain, after column chromatography, 0.88 g (2.35 mmol, 27% yield) of a yellow viscous liquid that after a while turned into a beige solid, m.p. = 126 °C. 1H-NMR: δ 7.60 (b, 1H, NH), 7.31 (d, 2H, = 8.5, H-9), 6.91 (d, 2H, = 8.5, H-8), 6.45 (s, 1H, H-6), 5.96 (s, 1H, H-14), 5.86 (s, 1H, H-4), 2.27, 2.25, 2.20, 2.18 (s, 3H each, 4CH3), 1.92 (s, 6H, 2CH3). 13C-NMR: δ 149.2 (C-13), 147.9 (C-3), 144.0 (C-18,20), 140.0 (C-15), 139.7 (C-5), 139.6 (C-10), 139.0 (C-7), 127.9 (2C-8), 124.8 (2C-9), 113.6 (C-19), 107.2 (C-14), 105.8 (C-4), 57.0 (C-6), 14.0, 13.7, 12.7, 11.5 (4CH3), 11.8 (2CH3). IR (neat, ν/cm−1): 1613, 1589 (C=N), 1554 (C=C), 1519 (Car), 1425 (CH3), 749 (pyrazole out of plane). MS (%): 374.0 (M+, 3), 279.0 (100), 94.8 (67.5). EA % found [calculated for C22H26N6 (374.48 g·mol−1)]: 70.20 (70.56, C), 7.10 (7.00, H), 21.82 (22.40, N).

4,4′-((4-(3,5-Dimethyl-1H-pyrazol-1-yl)phenyl)m<span class="Chemical">ethylene)bis(<class="Chemical">span class="Chemical">3,5-dimethyl-1H-pyrazole) (. Synthesized following the procedure described in Section 3.4.3 after heating at 160 °C for 72 h (Table 1, entry 10). Excess PzMe2 was sublimed and the remaining solid was stirred twice in 25 mL of 10% NaHCO3 solution, decanted, washed twice with 50 mL of water, filtered and air dried. After column chromatography, 0.460 g (1.23 mmol, 14% yield) of a pale beige solid which decomposes at 249 °C was isolated. 1H-NMR: δ 12.0 (b, 2H, NH), 7.38 (d, 2H, = 8.0, H-9), 7.13 (d, 2H, = 7.4, H-8), 6.03 (s, 1H, H-14), 5.3 (s, 1H, H-6), 2.24, 2.15 (s, 3H each, 2CH3), 1.72 (b, 12H, 4CH3). 13C-NMR: δ 148.3 (C-13), 142.7 (b, 2C-5 and 2C-3), 142.6 (C-7), 139.7 (C-15), 138.2 (C-10), 129.6 (2C-8), 124.5 (2C-9), 115.7 (2C-4), 107.6 (C-14), 39.3 (C-6), 14.0, 12.8 (2CH3), 11 (b, 4CH3). IR (neat, ν/cm−1): X (C=N), 1558 (C=C), 1517 (Car), 1413 (CH3), 760 (pyrazole out of plane). EA % found [calculated for C22H26N6 (374.48 g·mol−1)]: 69.41 (70.56, C), 7.03 (7.00, H), 21.52 (22.40, N).

<span class="Chemical">(3,5-Dimethyl-1H-pyrazol-1-yl)(phenyl)methanone (. Synthesized following the procedure 3.4.1 to afford 0.173 g (6%) of a yellow viscous liquid, after column chromatography. 1H-NMR: δ 8.00 (d, 2H, = 8.0, H-8), 7.56 (t, 1H, = 7.5, <class="Chemical">span class="Gene">H-10), 7.46 (t, 2H, = 7.4, H-9), 6.06 (s, 1H, H-4), 2.63, 2.25 (s, 3H each, 2CH3). 13C-NMR: δ 168.7 (C-7), 152.4 (C-3), 145.3 (C-5), 132.7 (C-10), 131.6 (C-8), 128.1 (C-9), 111.4 (C-4), 14.6, 14.1 (2CH3). IR (neat, ν/cm−1): 1694 (C=O), 1583 (C=C), 1448 (CH3). MS (%): 200.9 (M+, 7.5), 172.0 (11.3), 104.9 (100), 76.9 (45.0), 51.0 (20).

<span class="Chemical">4-(3,5-Dimethyl-1H-pyrazol-1-yl)benzaldehyde (. Synthesized following procedure 3.4.1 to afford 0.343 g (10%) of a yellow viscous liquid after column chromatography. 1H-NMR: δ 10.04 (s, 1H, CHO), 7.97 (d, 2H, = 8.34, H-8), 7.67 (d, 2H, = 8.1, H-7), 6.06 (s, 1H, H-4), 2.41, 2.31 (s, 3H <class="Chemical">span class="Chemical">each, 2CH3). 13C-NMR: δ 191.4 (C-10), 150.5 (C-9), 145.0 (C-5), 140.0 (C-6), 134.5 (C-3) 130.9 (C-8), 124.1 (C-7), 108.9 (C-4), 13.8, 13.2 (2CH3). IR (neat, ν/cm−1): 1697 (C=O), 1555 (C=C), 1514 (Car), 1418 (CH3). MS (%): 200.3 (M+, 27.5), 199.9 (100), 170.9 (11.3), 129.9 (17.5), 76.9 (20).

3.6. Temperature Effects Experiments

Four ampoules containing 1.000 g of <span class="Chemical">PzMe2 (10.4 mmol), previously ground in a mortar, and 0.250 mL of <class="Chemical">span class="Chemical">PhCCl3 (1.7 mmol) each were cooled at −30 °C and sealed under vacuum. The reference ampoule was introduced into a preheated oven at 80 °C and heated at the same temperature for 24 h. The other three ampoules were heated in two steps of temperature at 80/100, 80/120 and 80/160 °C for 24 h at each temperature. The obtained viscous reaction mixtures were dissolved in 30 mL of CHCl3 to homogenize and the solvent was evaporated to dryness, except the last ampoule whose content was homogenized by grinding it in a mortar. Samples of 10 mg/mL in methanol as solvent were prepared and then diluted to achieve 2.5 mg/mL for HPLC measurements. Chromatograms were recorded with 10 µL of each sample eluted in the same conditions as the calibration curve. Calibration curves were obtained from methanol solutions of 2.0, 1.5, 1.0 and 0.5 mg/mL of compounds 1a–4 each.

3.7. Time Effect Experiments

Three ampoules were prepared as described for temperature effects but starting with 5.00 g of <span class="Chemical">PzMe2 (52.0 mmol) and 1.23 mL of <class="Chemical">span class="Chemical">PhCCl3 (8.66 mmol) each, and heated in an oven at 120 °C for one, two and three days. The samples for HPLC were prepared as before.

4. Conclusions

In summary, the solventless synthesis of <span class="Chemical">tris(pyrazolyl)phenylmethane ligands <class="Chemical">span class="Chemical">C6H5C(PzR2)3 (R = H, Me), starting from PhCCl3 and 3,5-dimethylpyrazole (PzMe2) or pyrazole (Pz) was achieved. The sterically crowded C6H5C(PzMe2)3 is labile due to both steric and electronic reasons; therefore it is thermally transformed at 120 °C into bis(pyrazolyl)(p-pyrazolyl)phenylmethane ligand, PzMe2-C6H4CH(PzMe2)2. In this compound both PzMe2 rings are linked through the N-atom to the methine-bridge C-atom. At longer times of reaction or at temperatures beyond 120 °C, the binding mode of PzMe2 changes from N1 to C4. Reaction conditions were established to obtain compound 1a in 30%, 1b in 55%, 2 in 70%, 3 in 27% and 4 in 14% yields. The structures were proposed on the basis of 1H- and 13C-NMR spectroscopy and single crystal X-ray diffraction. The three PzMe2 rings, in compounds 1a and 1b, adopt a three-bladed propeller structure around the axial phenyl ring. Comparison to the structures of other tris(pyrazolyl)phenylmethane ligands allowed to conclude that steric effects determine the conformation adopted by pyrazole rings: (sp + 2ac) in the most crowded and (2sp + ap) in the less crowded compounds. Substituents in the pyrazole rings exert more steric demand than those located in the apical carbon atom.