Photoelectrochemical Immunosensor for Detection of Carcinoembryonic Antigen Based on 2D TiO2 Nanosheets and Carboxylated Graphitic Carbon Nitride.

Carcinoembryonic antigen (CEA) was used as the model, an ultrasensitive label-free photoelectrochemical immunosensor was developed using 2D TiO2 nanosheets and carboxylated graphitic carbon nitride (g-C3N4) as photoactive materials and ascorbic acid as an efficient electron donor. 2D TiO2 nanosheets was sythsized by surfactant self-assembly method and proved to have higher photoelectrochemical signals than TiO2 nanoparticles. Firstly, carboxylated g-C3N4 could be attached to 2D TiO2 nanosheets through the bond formed between carboxyl group of carboxylated g-C3N4 and TiO2. And the photocurrent of g-C3N4/TiO2 drastically enhances compared to carboxylated g-C3N4 and TiO2. Then, antibody of CEA was bonded to TiO2 through the dentate bond formed between carboxyl group of anti-CEA and TiO2, leading to the decrease of the photocurrents. As proven by PEC experiments and electrochemical impedance spectroscopy (EIS) analysis, the fabrication process of the immunosensor is successful. Under the optimal conditions, the intensity decreased linearly with CEA concentration in the range of 0.01~10 ng/mL. The detection limit is 2.1 pg/mL. The work provides an effective method for the detection of tumor markers and can be extended for the application in food safety and environmental monitoring analysis.

Photoelectrochemical (PEC) sensors are fabricated on photoactive electrodes which can convert photoirradiation to electrical signal. Therefore, photoactive materials are crucial for the performance of the PEC sensors. Many photoactive materials are metal-contained semiconductors, such as TiO2, CdSe, CdTe, ZnO, ZnS, etc123456789. Among them, titanium dioxide is one of the most commonly employed materials because of its nontoxicity, low-cost and brilliant photochemical and chemical stability. Nevertheless, due to a wide energy band gap of 3.0 eV, TiO2 can only absorb the ultraviolet light (<387 nm)10. So applications of pure TiO2 are also limited. Another class of photoactive materials is metal-free polymeric semiconductor. Graphitic carbon nitride (g-C3N4), a moderate energy bandgap of 2.7 eV, has paid more and more attentions because it is very stable in acid or alkaline electrolytes11. However, applications of pure g-C3N4 are also limited largely because of its low quantum efficiency and high electron−hole recombination rate. As mentioned above, researchers have therefore made great efforts to expand the application of pure TiO2 and pure g-C3N4 by various methods, such as coupling it with other materials, nanostructuring and doping1213. Thus, owing to the proper band level between g-C3N4 and TiO2, g-C3N4 and TiO2 are combined together leading to the easy separation of the photo-generated electron and hole. Although there are some references about the combination of g-C3N4 and TiO2, the morphology of TiO2 is maily focused on nanorod1014, nanoparticles11 and nanotube151617.

Herein, two-dimensional (2D) TiO2 nanosheets was prepared by forming inverse lamellar micelles of Pluronic P123 surfactant together with ethylene glycol (EG) co-surfactant in ethanol solvent. It is reported that 2D nanostructures exhibit superior catalytic, photovoltaic and electrochemical performances, due to their large surface-to-volume ratio and confined thickness on the atomic scale18. So they could have promising applications in sensors, and energy conversion and storage devices. Using carcinoembryonic antigen (CEA) as a model analyte, we developed a label-free photoelectrochemical immunosensor for detection of CEA based on 2D TiO2 nanosheets and carboxylated graphitic carbon nitride. CEA, a usual tumor marker, can be used for the early detection of recurrent diseases and indicate the effect of therapy in early breast cancer and gastrointestinal cancers as well as other tumor markers1920. Coupling carboxylated graphitic carbon nitride with 2D TiO2 nanosheets can evidently extend the absorption range, increase the utilization of light energy, and promote the photocurrent intensity. Then, antibody of CEA was immobilized through the dentate bond formed between carboxyl group of anti-CEA and TiO2, leading to the decrease of the PEC signal. The decreased signal is proportional to the logarithm of CEA concentration. The CEA immunosensor exhibits high sensitivity, good selectivity and wide linear range.

Experimental

Materials and reagents

Titanium isopropoxide (TTIP, 95%), ethylene glycol (EG) and ascorbic acid were purchased from Sinopharm Chemical Reagent Co., Ltd. (China). The CEA and corresponding antibody were purchased from Beijing Dingguo Changsheng Biotechnology Co. Ltd. (China). Bovine serum albumin (BSA, 96–99%) were purchased from Sigma-Aldrich (Beijing, China). All other chemicals were of analytical grade and used without further purification. ITO glass (resistivity 10 Ω/sq) is obtained from Zhuhai Kaivo Electronic Components Co. Ltd., China.

Apparatus

The scanning electron microscope (SEM) images were obtained by the field emission SEM (ZEISS, Germany). Photoelectrochemical (PEC) measurements were performed on an electrochemical workstation (Zahner Zennium PP211, Germany).

Synthesis of TiO2 nanosheet

TiO2 was prepared according to the literature1821. 1.05 g TTIP was added into 0.74 g concentrated HCl solution under vigorous stirring (solution A); and 0.2 g Pluronic P123 was dissolved in 3.0 g ethanol (solution B) under stirring for 15 min. Then, solution B was added into solution A and stirred for another 30 min. Subsequently, 2.5 mL TTIP solution with 20 mL EG was transferred into an autoclave and heated at 150 °C for 20 h. After cooled to room temperature naturally, the resulting solid powder was collected by centrifugation and washed with ethanol several times. The final products were then dried at 80 °C for 24 h.

Synthesis of carboxylated g-C3N4

Carboxylated g-C3N4 was prepared as described previously with our reference22. In brief, 5.0 g of white melamine powder was put into a covered ceramic crucible and heated at 550 °C for 4 h in a muffle furnace. The yellow g-C3N4 product was ground to powder after cooling to room temperature. Then, 1 g g-C3N4 powder was placed into 100 mL 5 mol/L HNO3 and refluxed for 24 h at 125 °C. After cooling to room temperature, the refluxed product was centrifuged and washed with water until pH reached 7. Finally, the resulting product was dried at 35 °C for 12 h in vacuum.

Synthesis of carboxylated g-C3N4/TiO2 solution

In brief, 0.5 mg carboxylated g-C3N4 powder was dispersed in 5 mL water by ultrasonication for over 2 h. Then, 20 mg TiO2 powder was added to the above suspension and stirred for 24 h. After that, the solution was centrifugated and the products were redispersed in 5 mL of water.

Fabrication of PEC immunosensor

The illustration of PEC immunosensor fabrication process is depicted in Fig. 1. ITO slices (3 × 0.5 cm2) were sonicated in acetone, ethanol and water consecutively for 30 min and dried under a N2 stream. 6 μL of carboxylated g-C3N4/TiO2 solution was dropped on the surface of the pre-cleaned ITO and dried after air drying, the film was sintered at 450 °C for 30 min and then cooled down to the room temperature. Then, 4 μL of 10 μg/mL anti-CEA solution was bonded onto TiO2 for 1 h via the bond formed between carboxyl group of anti-CEA and TiO2 at 4 °C for 1 h2324. The unreacted active sites on the electrode surface were deactivated by 6 μL of 1% bovine serum albumin (BSA) solution for 1 h. Finally, 6 μL of CEA solutions with different concentrations were incubated for 1 h the electrode was incubated with different concentration of CEA for 1 h min at 4 °C and then washed with buffer solution to remove the excess CEA. Thus, the PEC immunosensor was fabricated completely and was ready to be used.

Figure 1

PEC measurements

Photocurrent was measured by the current–time curve experimental technique on a photoelectrochemical workstation at a bias voltage of 0.1 V with light intensity of 150 W/cm2. All experiments were carried out using a conventional three electrodes system with a modified ITO as working electrode, a Pt wire as counter electrode, and a saturated Ag/AgCl electrode as reference electrode.

Results and Discussion

Characterization of TiO2 nanosheet

SEM images were used to confirm the successful synthesis of nanomaterials with different morphology. Figure 2 show the SEM images of TiO2 (A) and carboxylated g-C3N4 (B). Obviously, TiO2 exists in the form of groups of nanosheets. And the prepared carboxylated g-C3N4 also has the nanosheet structure.

Figure 2

SEM of TiO2 nanosheets (A) and carboxylated g-C3N4 (B).

Characterization of the immunosensor

Electrochemical impedance spectroscopy (EIS), a useful tool for evaluating electron transfer resistance, was used to monitor the stepwise modification of the electrodes. The semicircle diameter corresponds to the electron transfer resistance (Ret), which reflects the restricted diffusion of the redox probe accessing the layer25. The measurements were carried out in 5.0 mmol/L [Fe(CN)6]3−/4− solution containing 0.1 mol/L KCl and the result were shown in Fig. 3A. Non-modified ITO electrode showed a small semicircle diameter (curve a), implying a low electron transfer resistance. After coating of carboxylated g-C3N4/TiO2 composite (curve b), semicircle diameter increases gradually because both carboxylated g-C3N4 and TiO2 as semiconductors evidently reduced the ability of the redox probe to access the electrode surface. The sequential immobilization of CEA antibody (curve c), BSA (curve d) and CEA (curve e) led to gradual increase of the electron transfer resistance because of the insulation properties of protein.

Figure 3

EIS in the presence of 5.0 mmol/L [Fe(CN)6]3−/4− solution containing 0.1 mol/L KCl (A) and photocurrent–time curves in 0.1 mol/L PBS (pH = 7.0) containing 0.1 mmol/L AA with 0.1 V applied potential and 430 nm excitation light. (B) (a) ITO (b) ITO/g-C3N4/TiO2 composite (c) ITO/g-C3N4/TiO2/Anti-CEA (d) ITO/g-C3N4/TiO2/Anti-CEA/BSA (e) ITO/g-C3N4 /TiO2/Anti-CEA/BSA/CEA.

In order to further confirm that the electrode was modified successfully, the stepwise fabrication process of the immunosensor was also characterized by PEC measurements, as shown in Fig. 3B. Compared with the ITO (curve a), the photocurrent response (curve b) was enhanced greatly after carboxylated g-C3N4/TiO2 composite was immobilized on it subsequently, suggesting that carboxylated g-C3N4/TiO2 have good PEC properties. With the loading of CEA antibody (curve c), BSA (curve d) and CEA (curve e) onto the modified electrode surface successively, the photocurrent intensity decreased which could be attributed to the block of biomacromolecules. Both the above results were consistent with the fact that the electrode was modified as expected.

The mechanism of electron transfers in g-C3N4/TiO2 PEC immunosensor in ascorbic acid (AA) electrolyte probably is that high electron−hole recombination rate in g-C3N4 results in low PEC activity, when g-C3N4/TiO2 composites are exposure, the photo-generated electrons from g-C3N4 can transfer from conduction band of g-C3N4 to the conduction band of TiO2. Because the conduction band and valence band edges of g-C3N4 are higher than those of TiO2 nanosheets, the above transfer process of photo-generated carriers is easy. AA is a kind of excellent electron donor, which could block the recombination of photo-generated electrons and holes and meanwhile promote the electron transfer from conduction band of TiO2 nanosheets to the ITO electrode. The specific binding of CEA to its antibody blocked the electron transfer from AA to g-C3N4/TiO2 composite, resulting in the recombination of photo-generated holes and electrons, which could explain a decrease in photocurrent. Moreover, the photocurrent intensity decreased gradually with the increase of CEA concentration. Therefore, the quantitative detection of CEA is achieved by monitoring the photocurrent decrease after the binding of CEA.

Optimization of experimental conditions

As shown in Fig. 4A, no PEC signal were found for the ITO (curve a). Compared with the ITO, the PEC signal changed only a little after modified with g-C3N4 (curve b) due to the low quantum efficiency and high electron−hole recombination rate of g-C3N4. Moreover, TiO2 showed obvious PEC signal, and the photocurrent intensity of TiO2 nanosheets (curve d) was 30% higher than that of TiO2 nanoparticles (curve c). It illustrates that TiO2 with different morphology has different photoelectric response performance, and nanosheet is superior to nanoparticles in this system. Although pure g-C3N4 did not show obvious PEC signal, but when it was combined with TiO2, the PEC signal was significantly increased (curve e), which was 12% higher than that of pure TiO2 nanosheets and much larger than the sum of the two kinds of nanomaterials, suggesting there is energy level matching between g-C3N4 and TiO2. This is the reason why both carboxylated g-C3N4 and TiO2 were chosen as photoactive materials.

Figure 4

Photocurrent responses of different modified materials (A) effect of pH (B) the concentration of TiO2 (C) and the concentration of AA (D) on the photocurrent intensity. (a) ITO (b) ITO/g-C3N4 (c) ITO/TiO2 nanoparticles (d) ITO/TiO2 nanosheets (e) ITO/g-C3N4/TiO2 composite.

To obtain an optimal PEC signal, pH value of substrate solution was investigated. Keeping the concentrations of CEA constant, the effect of pH on the photocurrent intensity was studied over a pH range from 5.0–8.0, as shown in Fig. 4B. The photocurrent intensity increased with the increase of pH from 5.0–7.0 and reached the maximum. After that, the photocurrent intensity decreased accordingly with pH increasing from 7.0–8.0. This suggests that the neutral condition is more advantageous to the photoelectric response of the carboxylated g-C3N4 and TiO2 nanosheets system. Therefore, pH 7.0 was chosen as the optimal value.

The effect of TiO2 concentration was also tested. As shown in Fig. 4C, the photocurrent intensity increased when TiO2 concentration increased from 1 to 4 mg/mL because more photoactive materials are formed and light absorption is enhanced. After that, the photocurrent intensity is decreased because thicker C3N4/TiO2 film could also lead to increased diffusion resistance for electron motion. Thus, 4 mg/mL TiO2 was chosen for subsequent study.

The concentration of AA as an efficient electron donor was evaluated to improve the photocurrent response of the PEC sensor. It can be seen from Fig. 4D that the photocurrent intensity reached a maximum value at 0.1 mol/L AA. Thus, 0.1 mol/L AA PBS solution (pH 7.0) was used as the buffer electrolyte for CEA detection.

Under the optimal conditions, a series of photoelectrochemical immunosensors were incubated with different concentrations of CEA and subsequent determination was carried out. As expected, the photocurrents decreased with the increase of CEA concentration due to the biomolecular insulation properties of CEA. Moreover, it can be seen from Fig. 5 that the photocurrent intensity decreased linearly with CEA concentration in the range from 0.01–10 ng/mL with a detection limit of 2.1 pg/mL (S/N = 3). Table 1 shows the comparison of the proposed photoelectrochemical immunosensors with other previously reported immunosensors for the detection of CEA2627282930. As seen from the table, the detection limit of this work are superior to the previously reported immunosensors, indicating that the proposed PEC immunosensor has a good performance.

Figure 5

Table 1

Comparison with other previously reported immunosensors for the detection of CEA.

Materials	Detection ranges (ng/mL)	Detection limits (ng/mL)	References
CS–CNTs–GNPs nanocomposite film	0.1–2.0	0.04	26
[Ag–Ag2O]/SiO2 nanocomposite material	0.5–160	0.14	27
Thi@NPG/AuNPs	0.01–100	0.003	28
AuNP@nafion/FC@CHIT	0.01–150	0.0031	29
HRP-anti-CEA-NGGN	0.05–350	0.01	30
Carboxylated g-C3N4/TiO2 nanosheets	0.01–10	0.0021	This work

Stability and Selectivity

The stability of the designed immunosensor was also evaluated by using a prepared PEC immunosensor for the detection of 5 ng/mL CEA. The photocurrent responses were recorded under several on/off irradiation cycles for 550 s. As shown in Fig. 6A, there was only a little change of the photocurrent, indicating the developed PEC sensors have stable photocurrent response for CEA detection.

Figure 6

The stability of the immunosensor incubated with 5 ng/mL CEA under several on/off irradiation cycles for 550 s (A) and the selectivity of the immunosensor (B). 5 ng/mL CEA (1), 5 ng/mL CEA + 50 ng/mL PSA (2), 5 ng/mL CEA + 50 ng/mL H-IgG (3), 5 ng/mL CEA + 50 ng/mL BSA (4), 5 ng/mL CEA + 50 ng/mL glucose (5).

Figure 6B shows the selectivity test of the ECL immunosensor for 5 ng/mL CEA. The photocurrents were measured by mixing 5 ng/mL of CEA with 50 ng/mL prostate-specific antigen (PSA), 50 ng/mL human immune globulin G (H-IgG), 50 ng/mL BSA and 50 ng/mL glucose, respectively. The photocurrent exhibited no obvious change compared with the 5 ng/mL of CEA, which indicated excellent selectivity and specificity of the PEC immunosensor for CEA.

Serum sample analysis

The amount of CEA was measured 5 times in human serum sample and the relative standard deviation (RSD) was calculated to obtain the precision. The accuracy was also studied through a recovery experiment using standard addition method. 1.00 ng/mL CEA standard solution was added to the corresponding samples. With the same experiments measured for five times, the average recovery was calculated. It can be found from Table 2 that the relative standard deviation is 3.1% and the recovery is 99.2%. Hence, the proposed immunosensor can be used for CEA detection with satisfied results.

Table 2

Results for the determination of CEA in human serum sample.

Sample	Content of PSA (ng/mL)	Average (n = 5, ng/mL)	RSD (%)	Added (ng/mL)	Recovery value (ng/mL)	Recovery (n = 5, ng/mL)
Human serum	1.35	>1.39	>3.1	1.00	1.03	>99.2
	1.42			1.00	0.95
	1.45			1.00	1.01
	1.37			1.00	0.92
	1.36			1.00	1.05

Conclusions

This work demonstrated a label-free photoelectrochemical immunosensor for detection of carcinoembryonic antigen using carboxylated g-C3N4 and 2D TiO2 nanosheets as photoactive materials. 2D TiO2 nanosheets exhibits better photocatalytic activities than TiO2 nanoparticles and g-C3N4 can improve its photocatalytic performance due to the good energy level matching. Great photocatalytic activities of g-C3N4/TiO2 nanosheets together with the specificity of immunoreaction made sensitive detection of CEA possible. The proposed immunosensor has excellent performance with high sensitivity, good selectivity and stability. Moreover, this strategy could be used to develop photoelectrochemical immunosensors for other targets.

Additional Information

How to cite this article: Wang, H. et al. Photoelectrochemical Immunosensor for Detection of Carcinoembryonic Antigen Based on 2D TIO2 Nanosheets and Carboxylated Graphitic Carbon Nitride. Sci. Rep. 6, 27385; doi: 10.1038/srep27385 (2016).