Literature DB >> 22686127

Comparison of acrylic and titanium cranioplasty.

Yahia Z Al-Tamimi1, Priyank Sinha, Mili Trivedi, Craig Robson, Tamara A Al-Musawi, Naveed Hossain, Christopher Mumford, Gerry Towns.   

Abstract

INTRODUCTION: There are many indications for cranioplasty with an increasing incidence partly attributable to an increase in decompressive craniectomy following trauma and stroke. The aim of this study was to compare the survival of acrylic and titanium cranioplasties used in our department.
MATERIALS AND METHODS: Retrospective cohort study of 126 patients who underwent cranioplasty between 1997 and 2007. A comparison was made between those with acrylic (n = 61) and titanium (n = 65) cranioplasties. There was no significant difference in age and length of time between craniectomy and cranioplasty between the two groups. The indications for titanium cranioplasty tended to be classified as 'high risk' indications including trauma and stroke. A higher rate of pre-existing infection was noted in the acrylic group. Mean follow-up was 97.2 and 34 months for acrylic and titanium cranioplasties respectively.
RESULTS: Mean survival (95% confidence intervals) was 135 months (134-153) and 92 months (82-102) for acrylic and cranioplasty respectively. Out of 13 failures, only two were associated with pre-existing infection. Overall cumulative survival was better for acrylic cranioplasty although this difference did not reach statistical significance. DISCUSSION: Although survival of acrylic cranioplasty appears to be better than titanium plates, there is no statistical significance. Acrylic has the advantage of being able to be applied at the time of surgery without any planning and does not cause artefact on future imaging. Titanium cranioplasty is strong, light-weight and inert and can be fashioned in the pre-operative setting.

Entities:  

Mesh:

Substances:

Year:  2012        PMID: 22686127     DOI: 10.3109/02688697.2011.633640

Source DB:  PubMed          Journal:  Br J Neurosurg        ISSN: 0268-8697            Impact factor:   1.596


  8 in total

1.  Factors influencing the outcome (GOS) in reconstructive cranioplasty.

Authors:  U R Krause-Titz; N Warneke; S Freitag-Wolf; H Barth; H M Mehdorn
Journal:  Neurosurg Rev       Date:  2015-12-01       Impact factor: 3.042

Review 2.  The Materials Utilized in Cranial Reconstruction: Past, Current, and Future.

Authors:  Haley Meyer; Syed I Khalid; Amir H Dorafshar; Richard W Byrne
Journal:  Plast Surg (Oakv)       Date:  2020-09-04       Impact factor: 0.558

3.  Polymethylmethacrylate imbedded with antibiotics cranioplasty: An infection solution for moderate and large defects reconstruction?

Authors:  Paulo Valdeci Worm; Tobias Ludwig do Nascimento; Fabricio do Couto Nicola; Eduardo Farias Sanches; Carlos Fernando Dos Santos Moreira; Luiz Pedro Willimann Rogério; Marcelo Martins Dos Reis; Guilherme Finger; Marcus Vinicius Martins Collares
Journal:  Surg Neurol Int       Date:  2016-11-09

4.  Early experience with patient-specific low-cost 3D-printed polymethylmethacrylate cranioplasty implants in a lower-middle-income-country: Technical note and economic analysis.

Authors:  Mohammad Ashraf; Nabeel Choudhary; Usman Ahmad Kamboh; Muhammad Asif Raza; Kashif Ali Sultan; Naseeruddin Ghulam; Syed Shahzad Hussain; Naveed Ashraf
Journal:  Surg Neurol Int       Date:  2022-06-23

5.  Reconstruction of cranial defect with patient-specific implants: Four different cost-effective techniques.

Authors:  Dushyant Chauhan; Probodh Kumar Chattopadhyay; Ashish Thakur
Journal:  Natl J Maxillofac Surg       Date:  2022-04-20

6.  Reconstruction of Large Calvarial Defects Using Titanium Mesh Versus Autologous Split Thickness Calvarial Bone Grafts: A Comprehensive Comparative Evaluation of the Two Major Cranioplasty Techniques.

Authors:  Colonel Priya Jeyaraj
Journal:  J Maxillofac Oral Surg       Date:  2017-09-27

7.  Warfare-related secondary anterior cranioplasty.

Authors:  Ali Ebrahimi; Nasrin Nejadsarvari; Hamid Reza Rasouli; Azin Ebrahimi
Journal:  Ann Maxillofac Surg       Date:  2016 Jan-Jun

8.  Effect of Pressure, Post-Pressing Time, and Polymerization Cycle on the Degree of Conversion of Thermoactivated Acrylic Resin.

Authors:  Rafaella de S Leão; Sandra L D de Moraes; Kátia A da S Aquino; Cristina P Isolan; Bruno G da S Casado; Marcos A J R Montes
Journal:  Int J Dent       Date:  2018-08-15
  8 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.