Literature DB >> 20229895

Sensitivity calibration procedures in optical-CT scanning of BANG 3 polymer gel dosimeters.

Y Xu1, Cheng-Shie Wuu, Marek J Maryanski.   

Abstract

The dose response of the BANG 3 polymer gel dosimeter (MGS Research Inc., Madison, CT) was studied using the OCTOPUS laser CT scanner (MGS Research Inc., Madison, CT). Six 17 cm diameter and 12 cm high Barex cylinders, and 18 small glass vials were used to house the gel. The gel phantoms were irradiated with 6 and 10 MV photons, as well as 12 and 16 MeV electrons using a Varian Clinac 2100EX. Three calibration methods were used to obtain the dose response curves: (a) Optical density measurements on the 18 glass vials irradiated with graded doses from 0 to 4 Gy using 6 or 10 MV large field irradiations; (b) optical-CT scanning of Barex cylinders irradiated with graded doses (0.5, 1, 1.5, and 2 Gy) from four adjacent 4 x 4 cm2 photon fields or 6 x 6 cm2 electron fields; and (c) percent depth dose (PDD) comparison of optical-CT scans with ion chamber measurements for 6 x 6 cm2, 12 and 16 MeV electron fields. The dose response of the BANG3 gel was found to be linear and energy independent within the uncertainties of the experimental methods (about 3%). The slopes of the linearly fitted dose response curves (dose sensitivities) from the four field irradiations (0.0752 +/- 3%, 0.0756 +/- 3%, 0.0767 +/- 3%, and 0.0759 +/- 3% cm(-1) Gy(-1)) and the PDD matching methods (0.0768 +/- 3% and 0.0761 +/- 3% cm(-1) Gy(-1)) agree within 2.2%, indicating a good reproducibility of the gel dose response within phantoms of the same geometry. The dose sensitivities from the glass vial approach are different from those of the cylindrical Barex phantoms by more than 30%, owing probably to the difference in temperature inside the two types of phantoms during gel formation and irradiation, and possible oxygen contamination of the glass vial walls. The dose response curve obtained from the PDD matching approach with 16 MeV electron field was used to calibrate the gel phantom irradiated with the 12 MeV, 6 x 6 cm2 electron field. Three-dimensional dose distributions from the gel measurement and the Eclipse planning system (Varian Corporation, Palo Alto, CA) were compared and evaluated using 3% dose difference and 2 mm distance-to-agreement criteria.

Entities:  

Mesh:

Substances:

Year:  2010        PMID: 20229895      PMCID: PMC2826388          DOI: 10.1118/1.3298017

Source DB:  PubMed          Journal:  Med Phys        ISSN: 0094-2405            Impact factor:   4.071


  32 in total

1.  Image registration of BANG gel dose maps for quantitative dosimetry verification.

Authors:  S L Meeks; F J Bova; M J Maryanski; L A Kendrick; M K Ranade; J M Buatti; W A Friedman
Journal:  Int J Radiat Oncol Biol Phys       Date:  1999-03-15       Impact factor: 7.038

2.  Temperature increases associated with polymerization of irradiated PAG dosimeters.

Authors:  Greg J Salomons; Yong S Park; Kim B McAuley; L John Schreiner
Journal:  Phys Med Biol       Date:  2002-05-07       Impact factor: 3.609

3.  Characterization of a new radiochromic three-dimensional dosimeter.

Authors:  P Y Guo; J A Adamovics; M Oldham
Journal:  Med Phys       Date:  2006-05       Impact factor: 4.071

4.  Three-dimensional dose verification for intensity modulated radiation therapy using optical CT based polymer gel dosimetry.

Authors:  Cheng-Shie Wuu; Y Xu
Journal:  Med Phys       Date:  2006-05       Impact factor: 4.071

5.  Initial evaluation of commercial optical CT-based 3D gel dosimeter.

Authors:  K T S Islam; James F Dempsey; Manisha K Ranade; Marek J Maryanski; Daniel A Low
Journal:  Med Phys       Date:  2003-08       Impact factor: 4.071

6.  Sensitivity calibration procedures in optical-CT scanning of BANG 3 polymer gel dosimeters.

Authors:  Y Xu; Cheng-Shie Wuu; Marek J Maryanski
Journal:  Med Phys       Date:  2010-02       Impact factor: 4.071

7.  Evaluation of polymer gels and MRI as a 3-D dosimeter for intensity-modulated radiation therapy.

Authors:  D A Low; J F Dempsey; R Venkatesan; S Mutic; J Markman; E Mark Haacke; J A Purdy
Journal:  Med Phys       Date:  1999-08       Impact factor: 4.071

8.  Polymer gels for magnetic resonance imaging of radiation dose distributions at normal room atmosphere.

Authors:  P M Fong; D C Keil; M D Does; J C Gore
Journal:  Phys Med Biol       Date:  2001-12       Impact factor: 3.609

9.  Optical CT reconstruction of 3D dose distributions using the ferrous-benzoic-xylenol (FBX) gel dosimeter.

Authors:  R G Kelly; K J Jordan; J J Battista
Journal:  Med Phys       Date:  1998-09       Impact factor: 4.071

10.  Introducing gel dosimetry in a clinical environment: customization of polymer gel composition and magnetic resonance imaging parameters used for 3D dose verifications in radiosurgery and intensity modulated radiotherapy.

Authors:  Remo A Crescenti; Stefan G Scheib; Uwe Schneider; Stefano Gianolini
Journal:  Med Phys       Date:  2007-04       Impact factor: 4.071

View more
  4 in total

1.  Sensitivity calibration procedures in optical-CT scanning of BANG 3 polymer gel dosimeters.

Authors:  Y Xu; Cheng-Shie Wuu; Marek J Maryanski
Journal:  Med Phys       Date:  2010-02       Impact factor: 4.071

2.  Optical and NMR dose response of N-isopropylacrylamide normoxic polymer gel for radiation therapy dosimetry.

Authors:  Asghar Mesbahi; Vahid Jafarzadeh; Nahideh Gharehaghaji
Journal:  Rep Pract Oncol Radiother       Date:  2012-04-17

3.  Three-Dimensional Dosimetry by Optical-CT and Radiochromic Gel Dosimeter of a Multiple Isocenter Craniospinal Radiation Therapy Procedure.

Authors:  Matheus Antonio da Silveira; Juliana Fernandes Pavoni; Alexandre Colello Bruno; Gustavo Viani Arruda; Oswaldo Baffa
Journal:  Gels       Date:  2022-09-13

4.  Effect of composition interactions on the dose response of an N-isopropylacrylamide gel dosimeter.

Authors:  Yuan-Jen Chang; Bor-Tsung Hsieh
Journal:  PLoS One       Date:  2012-10-12       Impact factor: 3.240

  4 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.