OBJECTIVE: The aim of this in vitro study was to assess microleakage underneath a filled pit-and-fissure sealant bonded to occlusal surfaces treated by four enamel etching techniques. SUMMARY BACKGROUND DATA: There has been no report of a study assessing microleakage of a pit-and-fissure sealant, comparing acid-etching, Er:YAG laser and air-abrasion for treating enamel surface. METHODS:Forty extracted human third molars were selected and randomly assigned into four groups of ten teeth: group I, the occlusal surfaces were acid-etched; group II, a very short pulsed Er:YAG laser was used to treat the surfaces; group III, aluminum oxide air-abrasion was associated with acid-etching; group IV, Er:YAG laser was associated with acid-conditioning. The surfaces were sealed and the teeth were stored for 7 days in distilled water. Then, specimens were thermocycled, immersed in a 0.2% rhodamine solution, sectioned, and analyzed for leakage using an optical microscope connected to a video camera. The images were digitized and analyzed by software that allowed microleakage assessment in millimeters. RESULTS: Statistical analysis showed that occlusal surfaces treated exclusively by the Er:YAG laser (group II) provided the poorest marginal sealing and that acid-etching (group I) was statistically similar to aluminum oxide air-abrasion + acid etching (group III) and to Er:YAG laser + acid-etching (group IV). CONCLUSIONS: The results suggest that complementing either air-abrasion or Er:YAG laser irradiation with a subsequent acid-conditioning did not lessen microleakage at the enamel-sealant interface when compared with an acid-etched group. It was also observed that treating the enamel surface exclusively by Er:YAG laser resulted in the highest degree of leakage.
RCT Entities:
OBJECTIVE: The aim of this in vitro study was to assess microleakage underneath a filled pit-and-fissure sealant bonded to occlusal surfaces treated by four enamel etching techniques. SUMMARY BACKGROUND DATA: There has been no report of a study assessing microleakage of a pit-and-fissure sealant, comparing acid-etching, Er:YAG laser and air-abrasion for treating enamel surface. METHODS: Forty extracted human third molars were selected and randomly assigned into four groups of ten teeth: group I, the occlusal surfaces were acid-etched; group II, a very short pulsed Er:YAG laser was used to treat the surfaces; group III, aluminum oxide air-abrasion was associated with acid-etching; group IV, Er:YAG laser was associated with acid-conditioning. The surfaces were sealed and the teeth were stored for 7 days in distilled water. Then, specimens were thermocycled, immersed in a 0.2% rhodamine solution, sectioned, and analyzed for leakage using an optical microscope connected to a video camera. The images were digitized and analyzed by software that allowed microleakage assessment in millimeters. RESULTS: Statistical analysis showed that occlusal surfaces treated exclusively by the Er:YAG laser (group II) provided the poorest marginal sealing and that acid-etching (group I) was statistically similar to aluminum oxide air-abrasion + acid etching (group III) and to Er:YAG laser + acid-etching (group IV). CONCLUSIONS: The results suggest that complementing either air-abrasion or Er:YAG laser irradiation with a subsequent acid-conditioning did not lessen microleakage at the enamel-sealant interface when compared with an acid-etched group. It was also observed that treating the enamel surface exclusively by Er:YAG laser resulted in the highest degree of leakage.
Authors: Batu Can Yaman; Begum Efes Guray; Can Dorter; Yavuz Gomeç; Oktay Yazıcıoglu; Dina Erdilek Journal: Lasers Med Sci Date: 2011-08-16 Impact factor: 3.161
Authors: Batu Can Yaman; Begüm Güray Efes; Can Dörter; Yavuz Gömeç; Dina Erdilek; Oktay Yazıcıoğlu Journal: Lasers Med Sci Date: 2010-02-17 Impact factor: 3.161