Literature DB >> 9151584

The influence of abutment surface roughness on plaque accumulation and peri-implant mucositis.

C M Bollen1, W Papaioanno, J Van Eldere, E Schepers, M Quirynen, D van Steenberghe.   

Abstract

Bacterial adhesion to intra-oral, hard surfaces is firmly influenced by the surface roughness to these structures. Previous studies showed a remarkable higher subgingival bacterial load on rough surfaces when compared to smooth sites. More recently, the additional effect of a further smoothening of intra-oral hard surfaces on clinical and microbiological parameters was examined in a short-term experiment. The results indicated that a reduction in surface roughness below R(a) = 0.2 microns, the so-called "thresholds R(a)", had no further effect on the quantitative/qualitative microbiological adhesion or colonisation, neither supra- nor subgingivally. This study aims to examine the long-term effects of smoothening intra-oral hard transgingival surfaces. In 6 patients expecting an overdenture in the lower jaw, supported by endosseus titanium implants, 2 different abutments (transmucosal part of the implant): a standard machined titanium (R(a) = 0.2 microns) and one highly polished and made of a ceramic material (R(a) = 0.06 microns) were randomly installed. After 3 months of intra-oral exposure, supra- and subgingival plaque samples from both abutments were compared with each other by means of differential phase-contrast microscopy (DPCM). Clinical periodontal parameters (probing depth, gingival recession, bleeding upon probing and Periotest-value) were recorded around each abutment. After 12 months, the supra- and subgingival samples were additionally cultured in aerobic, CO2-enriched and anaerobic conditions. The same clinical parameters as at the 3-month interval were recorded after 12 months. At 3 months, spirochetes and motile organisms were only detected subgingivally around the titanium abutments. After 12 months, however, both abutment-types harboured equal proportions of spirochetes and motile organisms, both supra- and subgingivally. The microbial culturing (month 12) failed to detect large inter-abutment differences. The differences in number of colony- forming units (aerobic and anaerobic) were within one division of a logarithmic scale. The aerobic culture data showed a higher proportion of Gram-negative organisms in the subgingival flora of the rougher abutments. From the group of potentially "pathogenic" bacteria, only Prevotella intermedia and Fusobacterium nucleatum were detected for anaerobic culturing and again the inter-abutment differences were negligible. Clinically, the smoothest abutment showed a slightly higher increase in probing depth between months 3 and 12, and more bleeding on probing. The present results confirm the findings of our previous short-term study, indicating that a further reduction of the surface roughness, below a certain "threshold R(a)" (0.2 microns), has no major impact on the supra- and subgingival microbial composition.

Entities:  

Mesh:

Substances:

Year:  1996        PMID: 9151584     DOI: 10.1034/j.1600-0501.1996.070302.x

Source DB:  PubMed          Journal:  Clin Oral Implants Res        ISSN: 0905-7161            Impact factor:   5.977


  74 in total

1.  Comparison of Root Surface Roughness Produced By Hand Instruments and Ultrasonic Scalers: An Invitro Study.

Authors:  Pawan Kumar; Swarga Jyoti Das; Saindhya Tora Sonowal; Jitendra Chawla
Journal:  J Clin Diagn Res       Date:  2015-11-01

2.  In vitro blood and fibroblast responses to BisGMA-TEGDMA/bioactive glass composite implants.

Authors:  Aous A Abdulmajeed; Anne K Kokkari; Jarmo Käpylä; Jonathan Massera; Leena Hupa; Pekka K Vallittu; Timo O Närhi
Journal:  J Mater Sci Mater Med       Date:  2014-01       Impact factor: 3.896

3.  The effects of polishing methods on surface morphology, roughness and bacterial colonisation of titanium abutments.

Authors:  Michele E Barbour; Dominic J O'Sullivan; Howard F Jenkinson; Daryll C Jagger
Journal:  J Mater Sci Mater Med       Date:  2007-03-27       Impact factor: 3.896

4.  Surface roughness and wear behavior of occlusal splint materials made of contemporary and high-performance polymers.

Authors:  Merve Benli; Beril Eker Gümüş; Yusuf Kahraman; Bilge Gökçen-Rohlig; Gülümser Evlioğlu; Olivier Huck; Mutlu Özcan
Journal:  Odontology       Date:  2019-10-14       Impact factor: 2.634

Review 5.  WITHDRAWN: Interventions for replacing missing teeth: partially absent dentition.

Authors:  Elliot Abt; Alan B Carr; Helen V Worthington
Journal:  Cochrane Database Syst Rev       Date:  2019-07-17

6.  Adhesion of oral streptococci to all-ceramics dental restorative materials in vitro.

Authors:  R Meier; I Hauser-Gerspach; H Lüthy; J Meyer
Journal:  J Mater Sci Mater Med       Date:  2008-05-13       Impact factor: 3.896

7.  Development of an animal model for Aggregatibacter actinomycetemcomitans biofilm-mediated oral osteolytic infection: a preliminary study.

Authors:  Marcelo O Freire; Parish P Sedghizadeh; Christoph Schaudinn; Amita Gorur; Jennifer S Downey; Jeong-Ho Choi; Weizhen Chen; Joong-Ki Kook; Casey Chen; Steven D Goodman; Homayoun H Zadeh
Journal:  J Periodontol       Date:  2011-01-11       Impact factor: 6.993

8.  The effect of mechanical and chemical polishing techniques on the surface roughness of heat-polymerized and visible light-polymerized acrylic denture base resins.

Authors:  Abdul Aziz Abdullah Al-Kheraif
Journal:  Saudi Dent J       Date:  2014-02-03

9.  The influence of implantoplasty on the diameter, chemical surface composition, and biocompatibility of titanium implants.

Authors:  Frank Schwarz; Gordon John; Jürgen Becker
Journal:  Clin Oral Investig       Date:  2016-12-24       Impact factor: 3.573

10.  Effects of sample preparation on bacterial colonization of polymers.

Authors:  Diana N Zeiger; Christopher M Stafford; Yajun Cheng; Stefan D Leigh; Sheng Lin-Gibson; Nancy J Lin
Journal:  Langmuir       Date:  2010-02-16       Impact factor: 3.882

View more

北京卡尤迪生物科技股份有限公司 © 2022-2023.