Literature DB >> 8592672

Structure of disintegrating pellets with regard to fractal geometry.

M Schröder1, P Kleinebudde.   

Abstract

PURPOSE: The aim of this study was to investigate the influence of the granulation liquid on pellet properties.
METHODS: Pellets containing propyphenazone were obtained by extrusion/spheronization using different 2-propanol/water mixtures as granulation liquids. The pore structure of the pellets was determined by mercury porosimetry. The fractal dimension of the pore system was calculated according to the model of the Menger sponge. Further characterization included SEM-photographs, disintegration, dissolution and tensile strength.
RESULTS: Fractions exceeding 40% 2-propanol in the fluid resulted in rapid dissolution rates of the pellets. This effect was caused by the rapid and complete disintegration of the pellets as compared to those obtained with less 2-propanol in the mixture. These phenomena were interpreted as being due to a change in the particle bonding of the pellets at concentrations of 40% 2-propanol. Evidence for this hypothesis resulted from the spheronization process, the tensile strength measurements and from SEM-photographs. The analysis of the pore system in terms of fractal dimensions implied a dependency of the fraction of 2-propanol in the granulation liquid on the pore structure. High fractions of 2-propanol resulted in lower fractal dimensions close to the dimension of the Menger sponge (2.727).
CONCLUSIONS: The structure of pellets can be markedly influenced by the composition of the granulation liquid. Investigations of the pore system in terms of fractal geometry are more useful for the explanation of pharmaceutical properties than if the pure values for the porosity are taken.

Entities:  

Mesh:

Substances:

Year:  1995        PMID: 8592672     DOI: 10.1023/a:1016209620953

Source DB:  PubMed          Journal:  Pharm Res        ISSN: 0724-8741            Impact factor:   4.200


  5 in total

1.  Note on a Method of Determining the Distribution of Pore Sizes in a Porous Material.

Authors:  E W Washburn
Journal:  Proc Natl Acad Sci U S A       Date:  1921-04       Impact factor: 11.205

2.  Matrix type controlled release systems: I. Effect of percolation on drug dissolution kinetics.

Authors:  J D Bonny; H Leuenberger
Journal:  Pharm Acta Helv       Date:  1991

3.  Design and use of a laboratory extruder for pharmaceutical granulations.

Authors:  F W Goodhart; J R Draper; F C Ninger
Journal:  J Pharm Sci       Date:  1973-01       Impact factor: 3.534

Review 4.  The concept of fractals in the pharmaceutical sciences.

Authors:  H P Koch
Journal:  Pharmazie       Date:  1993-09       Impact factor: 1.267

5.  The power-consumption-controlled extruder: a tool for pellet production.

Authors:  P Kleinebudde; A J Sølvberg; H Lindner
Journal:  J Pharm Pharmacol       Date:  1994-07       Impact factor: 3.765

  5 in total
  6 in total

1.  Extrusion/spheronization of pectin-based formulations. I. Screening of important factors.

Authors:  T Tho; P Kleinebudde; S A Sande
Journal:  AAPS PharmSciTech       Date:  2001-12-01       Impact factor: 3.246

2.  The crystallite-gel-model for microcrystalline cellulose in wet-granulation, extrusion, and spheronization.

Authors:  P Kleinebudde
Journal:  Pharm Res       Date:  1997-06       Impact factor: 4.200

3.  Fractal volume of drug distribution: it scales proportionally to body mass.

Authors:  V Karalis; L Claret; A Iliadis; P Macheras
Journal:  Pharm Res       Date:  2001-07       Impact factor: 4.200

Review 4.  Review on Starter Pellets: Inert and Functional Cores.

Authors:  Nikolett Kállai-Szabó; Miléna Lengyel; Dóra Farkas; Ádám Tibor Barna; Christian Fleck; Bálint Basa; István Antal
Journal:  Pharmaceutics       Date:  2022-06-18       Impact factor: 6.525

5.  Moistening liquid-dependent de-aggregation of microcrystalline cellulose and its impact on pellet formation by extrusion-spheronization.

Authors:  Srimanta Sarkar; Celine Valeria Liew
Journal:  AAPS PharmSciTech       Date:  2014-02-20       Impact factor: 3.246

6.  Dissolution rate improvement of telmisartan through modified MCC pellets using 32 full factorial design.

Authors:  Hetal Patel; Hiral Patel; Mukesh Gohel; Sanjay Tiwari
Journal:  Saudi Pharm J       Date:  2015-03-23       Impact factor: 4.330

  6 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.