Recent Advances in Two-Dimensional Quantum Dots and Their Applications.

Two-dimensional quantum dots have received a lot of attention in recent years due to their fascinating properties and widespread applications in sensors, batteries, white light-emitting diodes, photodetectors, phototransistors, etc. Atomically thin two-dimensional quantum dots derived from graphene, layered transition metal dichalcogenide, and phosphorene have sparked researchers' interest with their unique optical and electronic properties, such as a tunable energy bandgap, efficient electronic transport, and semiconducting characteristics. In this review, we provide in-depth analysis of the characteristics of two-dimensional quantum dots materials, their synthesis methods, and opportunities and challenges for novel device applications. This analysis will serve as a tipping point for learning about the recent breakthroughs in two-dimensional quantum dots and motivate more scientists and engineers to grasp two-dimensional quantum dots materials by incorporating them into a variety of electrical and optical fields.

1. Introduction

The field of material science and technology is evolving rapn>idly and currently provides a major contribution to research in nanoscale science, motivated by the need for novel materials with fascinating properties. The number of dimensions outside the nanoscale range (100 nm) in which particles are confined determines how a material is categorized. Nanomaterials, in general, are exceptionally tiny, with at least one dimension of 100 nanometers or less. Nanomaterials can have several confinement directions, such as one-dimensional confinement (e.g., surface films), two-dimensional confinement (e.g., strands or fibres), or three-dimensional confinement (e.g., particles). Quantum dots (QDs) are the artificial nanocrystals having confinement in all three dimensions with nanometer size that can transport electrons. By changing their sizes, the optical and electrical properties of quantum dots can be effectively tuned, resulting in the emission of specific wavelengths of light [1,2]. Smaller QDs with a diameter of 2–3 nm emit shorter wavelengths, generating colors such as blue and green, whereas larger QDs with a diameter of 5–6 nm emit longer wavelengths, such as orange or red [3,4]. The emission color and wavelength of QDs corresponding to their sizes are shown in Figure 1a; it can be seen that with increasing size, the emission wavelength increases. QDs are mainly composed of groups II-VI, III-V, and IV-VI materials in which the electron-hole pairs (excitons) are spatially confined in three dimensions (i.e., zero degree of freedom) owing to quantum confinement effect (QCE) [5,6]. The zero-dimensional QDs structures of InP QDs are shown in Figure 1b and InP/ZnSe/ZnS core-shell QDs in Figure 1c [7]. In core-shell QDs, the core and shell are usually made up of form II–VI, IV–VI, and III–V semiconductors in CdS/ZnS, CdSe/ZnS, CdSe/CdS, and InAs/CdSe configurations [8,9,10]. Core-shell QDs can mitigate the issue of low fluorescence quantum yield in originally passivated QDs by utilizing the shell to passivate the surface trap states. In addition, the shell protects against environmental changes and photo-oxidative degradation, and provides a second path for modularity. The size, shape, and composition of both the core and the shell can be precisely regulated, allowing the emission wavelength to be tuned over a broader range of wavelengths than for either individual semiconductor.

Figure 1

(a) Emission color and wavelength of QDs corresponding to their sizes (b) InP QDs; (c) InP/ZnSe/ZnS core-shell QDs [7]. Figure reproduced with permission from ACS Publications.

Quantum wires are electrically conducting wires with the quantum effects in two dimenpan class="Chemical">sions influencing their transport characteristics. pan class="Chemical">Since this phenomenon only happens in the nanometer scale, they are often known as nanowires (NWs). For a specific material, the significance of quantization is inversely proportional to the diameter of the nanowire [11]. It varies depending on the electronic properties of the material, especially the effective mass of the electrons. This means that it will be determined by how conduction electrons interact with the atoms in a particular material. Figure 2a shows CdSSe NWs dispersed on a low-index MgF2 substrate illuminated with a 405 nm laser emitting various colors from green to red along the length of the NWs [12]. Nanowires have a number of unique properties that cannot be found in bulk or three-dimensional materials. This is due to the fact that electrons in nanowires are quantum confined laterally and therefore occupy energy levels that are different from the traditional continuum of energy levels or bands found in bulk materials. Figure 2b shows the red illumination of CdSe-CdS quantum rods (QRs) upon excitation in the ultraviolet (UV) region [13]. The efficient overlap of electron and hole wave functions in CdSe-CdS QRs with a spherical seed embedded in an elongated shell contributes to the reduction of nonradiactive decay due to excitons trapped in surface defects, resulting in a high quantum efficiency of emission. Furthermore, the quasi-cylindrical symmetry of the CdS shell and the crystal field effect on the radiative charge recombination within the rods would also result in strongly linearly polarized luminescence along their axis.

Figure 2

(a) CdSSe nanowires dispersed on a low-index MgF2 substrate [12]. (b) CdSe-CdS quantum rods [13]. Figure reproduced with permission from ACS Publications and Wiley Online Library.

In two-dimenpan class="Chemical">sional nanomaterials (pan class="Chemical">2D), quantum confinement occurs in one direction exhibiting plate-like shapes and includes graphene, nanofilms, nanolayers, and nanocoatings. However, in bulk or 3D materials, there is no confinement in any dimension. When compared to bulk materials, layered 2D materials have a variety of unique features, including a high aspect ratio (surface-area-to-volume ratio) that is strongly related to the number of layers. From a scientific and technological standpoint, 2D materials such as graphene have a number of benefits over bulk 3D materials because their properties may be dynamically tuned via electrical, chemical, electrochemical, and other methods. Increased relative surface area and quantum effects are two major characteristics that cause the properties of 2D materials to differ dramatically from those of other materials such as 3D materials. These factors can change or improve the optoelectrical and mechanical properties of the materials. When a particle gets smaller, the surface has a higher proportion of atoms than the inside. As a result, when compared to bigger particles, nanoparticles have a substantially higher surface area per unit mass. Even with crystalline solids, as the size of their structural components shrinks, the material’s interface area expands, affecting both mechanical and electrical properties significantly. When matter’s size is reduced to the nanoscale, quantum effects can begin to dominate its properties. These can have an impact on a material’s optical, electrical, and magnetic properties, especially when the particle size gets closer to the nanoscale. Quantum dots and quantum well lasers for optoelectronics are examples of materials that take advantage of these features.

Although pan class="Chemical">Cd-based zero-dimensional QDs exhibit excellent properties, 2D-QDs have recently emerged as a paradigm with new possibilities and features with improved applicability due to their planar confinement [14,15,16]. Two-dimensional QDs are QDs or nanoparticles made out of layered inorganic materials or 2D sheets that have a unique luminescence and chemical capabilities due to their inherent 2D structure. The majority of 2D-QDs retain their 2D shape or lattices from their bulk form, but with improved solution dispersibility and surface functionalization capabilities. Two-dimensional QDs are typically made up of only a few layers or even a single layer of material having lateral dimensions of less than or equal to 10 nm. The bandgap of 2D-QDs can be tuned by optimizing their lateral dimension and number of layers. Two-dimensional QDs are very attractive for various applications such as sensing [17,18], catalysis [19,20,21], batteries [22,23], and biological applications [24] owing to their superficial functionalization and better solution processibility. In essence, 2D-QDs can be considered as QDs originating from the structure of 2D sheets with unique luminosity and chemical properties. There are different types of 2D-QDs, consisting of 2D-QDs with a single component, 2D-QDs with two elements, and 2D-QDs containing multiple components. Under 2D-QDs with a single element category, there exists carbon dots [25], phosphorene dots [26], and quasi 2D-QDs [27,28,29]. Carbon dots (CDs) are zero-dimensional carbon-based materials with significant amount of attention owing to their various advantages such as low toxicity, chemically inert, tunability, good water solubility, and physiochemical properties [30,31]. Only the CDs with 2D structure can be considered as 2D-QDs as they exhibit similar characteristics to that of semiconductor QDs in terms of photophysics and quantum effects. Phosphorene dots are a direct bandgap semiconductor material, primarily black phosphorous with a bandgap lying in between 0.3 and 2 eV and thickness less than 7 nm in its 2D form [32]. Quasi 2D-QDs are those elements of group IV and V such as Si, Ge, B, Pb, and Sn that can be formed in the form of nano-sheets, so they can serve as materials for 2D-QDs. However, there are no experimental studies on 2D-QDs with these materials so far, so there is still an unexplored promise and endless possibilities in the 2D-QDs family domain. Two-dimensional QDs containing two elements consist of Silicon Carbide (SiC) dots, C3N4 dots, Boron Nitride (BN) dots, transition metal dichalcogenides (TMDs) QDs, and transition metal oxides (TMOs) QDs. SiC dots are wide bandgap semiconductor QDs, which is very attractive for biomedical applications with advanced photoluminescence and long fluorescence lifetime due to efficient quantum confinement [33]. The g-C3N4 monolayer may be considered to be a graphene sheet containing units of tri-s-triazine connected by the amino group and may serve as another type of 2D-QDs [34]. BN quantum dots are analogous to C3N4 except carbon (C) is replaced by boron (B), resulting in honeycomb-free structure unlike in g-C3N4. BN dots show great potential for biological and optoelectronic applications owing to its wide bandgap of 5–6 eV and high quantum yield. TMDs dots are heavy metal-free quantum dots with a general formula of MX2, where M can be Mo, In, Pt, Cd, Ti, W, V, Nb, Ni, Re, Rb, Pb, Bi, Ta, Zr, Fe, and Hf; and X can include S, Se, and Te [35,36,37]. MoS2 QDs, which display remarkable metallic and other optical properties with the potential to drive significant developments in 2D material-based research, are the most common TMDs QDs. TMOs QDs are typically semiconductor QDs with a larger bandgap than that of TMDs with a general formula of MOx, where M can be Mo, Cr, Sc, W, etc., of which MoOx (x < 3) and WO3-x are the most investigated QDs [25,38,39]. Figure 3a represents the crystal structure of TMDs QDs that is composed of three atomic planes and often two atomic species: a metal and two chalcogens [40]. The honeycomb hexagonal lattice has three fold symmetry and can be used to establish mirror plane and inversion symmetry. At submicron scales, 3D materials no longer behave like their 2D counterparts, which can be advantageous. TMD monolayers are structurally stable, have a specific bandgap, and electron mobilities that are comparable to those of silicon, allowing them to be used in the fabrication of transistors [41]. Figure 3b shows representative scheme of the section of a field effect transistor based on a monolayer of MoS2. TMD monolayers are also particularly promising for optoelectronics applications due to their direct bandgap. Atomic layers of MoS2 have been used as a photodetector and multilayer MoS2 can be used to fabricate an ultrasensitive detector to be with a photoresponsivity reaching 880 AW−1, which is 106 times higher than the first graphene photodetectors [42]. Figure 3c shows a typical scheme of the section of ultrasensitive photodetector based on a monolayer of MoS2.

Figure 3

(a) Structure of 2-D Quantum dots. (b) Field effect transistor based on monolayer of MoS2. (c) Photodetector based on a monolayer of MoS2 [40].

Under pan class="Chemical">2D-QDs with multipan class="Chemical">ple components, there are MXene-type QDs and other 2D-QDs prepared from MXene-type materials. MXene-type QDs are the two-dimensional transition metal carbides, carbonitrides, and nitrides-based QDs with a general formula of Mn+1XnTx (n = 1–3), where M represents the transition metals, X represents the C or N elements, and Tx represents the surface termination groups such as –O, –F, or –OH [43]. Other 2D-QDs derived from MXene material include ternary 2D materials such as h-BNC [44], which is a hybridized boron nitride and graphene domains, doped TMDs [45], lamellar metal hydroxides [46], heterostructured TMDs [47], etc. Moreover, two-dimensional (2D) graphene has recently emerged as graphene quantum dots (GQDs) with impressive properties, the bandgap of which can easily be tuned to transform into zero-dimensional quantum dots. By allowing greater surface area, higher solubility, and flexibility of doping with other nanomaterials, the dimensions of GQDs can be modified to provide higher stability characteristics [48,49]. As the family of 2D materials continues to grow and the photoluminescence (PL) of the 2D-QDs is controlled by certain variables such as QCE, surface states, defects, doping, etc., it is essential to study the 2D-QDs PL. QCE is size-dependent and comes to existence in semiconductors when the sizes become comparable to the Bohr radius, resulting in the formation of low-dimensional materials with more advanced features as compared to bulk materials. The PL phenomenon in 2D-QDs can be explained by taking examples of two classes of CDs, one with graphitized carbon core (class 1) and the other with disordered carbon core (class 2). For the class 1 CDs, the energy gap between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LOMO) decreases with increasing size; however, a contrasting behavior for energy gap dependence on size has been observed for class 2 CDs. This inverse trend is due to the increased strain experienced by the excited state triggered by the disordered carbon core when the QD size is decreased. Hence, as the size of the QDs changes, the trend in the energy bandgap of 2D-QDs would influence the PL. The interaction between the 2D-QDs and the solvents also affects the characteristics of the PL as a strong surface interaction can lead to the luminescence and polarization properties being improved. It has been previously stated that the emission from surface energy traps will lead to the blue PL, while the red PL emission will result from the intrinsic emission from the QCE [50]. In addition, a significant amount of oxidation could generate more surface defects that serve as recombination centers for the excitons, which can influence the PL characteristics, resulting in a narrowing energy gap [51]. Besides oxygen-based groups, carboxyl or amine-based functional groups could cause major surface distortions by acting as non-radiative electron-hole recombination centers, thus affecting the PL characteristics [52]. The fluorescence characteristics of the 2D-QDs also rely on the difference in energy between the intrinsic state and the edge state, creating a significant influence on the 2D material properties [53]. Another important factor affecting the PL characteristics is the doping effect as sulfur or nitrogen doping could lead to a blue-shift, whereas the PL emission peak may experience a red-shift if boron or fluoride is used for doping. Two-dimensional QDs of graphenes and other materials, as well as optoelectronic devices based on them, have attracted a lot of attention in recent years. Many researches have claimed that MoS2 2D-QDs have strong photoresponsivity and detectivity due to outstanding light absorption and a decent PL quantum yield [54,55]. Photodetectors were expected to perform better with a hybrid technique that combined a high light absorption layer with a 2D layer structure. Phototransistors with a hybrid structure of PbS QDs and 2D WeS2 have been reported with outstanding performance and broadband photodetection [56]. Another hybrid structure integrating core-shell QDs and WS2 nanowalls exhibits great nonradiative energy transfer and excellent No2 gas sensing performance [57]. Through plasmonic enhanced photoluminescence, hybrid zero-dimensional core–shell CdSe/ZnS QD/two-dimensional monolayer WSe2 semiconductors with an Ag nanodisk (ND) can achieve a high color conversion efficiency of 53% [58]. A detailed explanation of these recent advances is provided in the following sections.

With all these features in various aspects, pan class="Chemical">2D-QDs have started to have pan class="Chemical">significant interest in a wide range of applications in recent years, such as sensors, batteries, white light emitting diodes (WLEDs), supercapacitors, photocatalysis, photodetectors, etc. While great advancements have been made, there are some missing remnants that are still struggling to be explored. In addition, in terms of material synthesis, the current growth, efficiency, and productivity of 2D-QDs are far from the criteria necessary for high output and mass production to be met for commercialization in different industries. Figure 4 gives an overview of the organization of the present 2D-QDs review. In this review, we discuss in detail the characteristics, synthesis of 2D-QDs in terms of recent development in various applications, and the challenges faced in terms of device applications.

Figure 4

Overview of the present 2-D quantum dots review.

2. Characteristics of 2D-QDs

The properties of pan class="Chemical">2D-QDs are quite fascinating in terms of broad emissions ranging from the deep UV to near-infrared (NIR) wavelengths that mainly depend on the size-dependent QCE, surface interaction with solvents, defects from ligands, synthesis temperature, etc. Two-dimensional QDs suspensions can emit blue or green light or sometimes red under UV irradiation, but they are transparent and colorless or light yellow and brown under daylight. As we have already mentioned, the size and the surface chemistry are critical factors for determining the PL of 2D-QDs. To mention a few examples, the green light emission from GQDs is attributed to the defect centers originated from ligands such as oxygenous functional groups, while the blue emission is due to intrinsic states in the highly crystalline structure. In addition, solvent types play an important role in deciding the PL color as green emissions will result from methanol, yellow from ethanol, and orange from hexanol. The explanation behind this is due to the fact that the size of QDs varies with the change in solvents and hence the emission wavelengths change. The following section describes the structural and optical characteristics of 2D-QDs in particular.

2.1. Excitons in Monolayer TMDs

Excitons in most semiconductors have a small pan class="Chemical">binding energy, usually about 10 meV, and a broad radius, which encompn>asses several atoms, making them Wannier–Mott typn>e excitons. They are so-called “free” excitons, which are delocalized states that are free to move around the pan class="Chemical">crystal as a single entity. Since the binding energies of excitons in most conventional semiconductors are usually in the same order or lower than thermal energy at room temperature, the excitons are easily dissociated by interactions with phonons. As a result, observing excitonic effects in conventional semiconductors at room temperature is challenging. TMD crystals, on the other hand, have a poor van der Waals layered structure and a large effective mass of valence/conduction bands, resulting in a high exciton binding energy and prominent excitonic effects in transitions at room temperature [59]. The more evident excitonic effects in TMD monolayer is attributed to substantial enhancement of Coulomb interactions in the 2D limit due to spatial confinement and poor dielectric screening [60,61]. This can lead to interesting many-particle phenomena including the creation of various forms of excitons, such as optically allowed and forbidden dark excitons, as well as spatially distributed interlayer excitons states. Figure 1a represents a schematic diagram of exciton, trion, and biexciton generation in TMDs through photoexcitation [62]. The valence and conduction band peaks of the monolayer TMDs are localized at the corners (K and K’ points) of the 2D hexagonal Brillouin zone, resulting in having a direct bandgap. Similar to graphene, this leads to the formation of two inequivalent valleys at the K and K’ points in momentum space. The lack of inversion symmetry causes spin–orbit coupling in monolayers, which induces valence band splitting, and seems to have no effect on conduction bands. As a result, two exciton peaks, A and B, will form owing to the existence of two possible vertical transitions from two spin-orbit split valence bands to a doubly degenerate conduction band. Figure 5b shows the photoluminescence (PL) and differential reflectance spectra of monolayer TMDs flakes on quartz substrate where A and B represent the resonance peaks corresponding to excitonic transitions [62]. For ultrathin samples, differential reflectance is an important indicator of absorbance. Because of the fast intra-valence-band relaxation processes leading to dominant formation of A excitons, the emission of A excitons is much more intense than that of B excitons. Near-degenerate exciton states induce strong absorption at higher energies (C peak). The monolayer TMDs allow the formation of excitons from both same and multi-valleys in the Brillouin zone by coupling between electron and hole in different valleys, as shown in Figure 5c [62]. The former exciton is considered a bright exciton since it normally recombines radiatively, while the latter exciton is called a dark exciton since direct recombination to emit a photon is prohibited as only cross recombination is allowed [63]. Excitons in monolayer TMDs are of Wannier type, which have localized wave functions and can move freely throughout the crystal despite their extremely high binding energy. The energy dispersion curves of exciton, trion, and biexciton have a parabolic shape, as shown in Figure 5d, reflecting the exciton’s freely translational motion [62]. However, because of their heavier masses, trion and biexciton have a smaller curvature than that of exciton. The increase in exciton energy caused by the addition of one more charge carrier characterizes the trion binding energy, Eb,T while biexciton binding energy, Eb,xx can be defined as the decrease of two isolated excitons after formation of a bound state. Hence, the trion binding energy Eb,T can be defined as the subtraction of exciton state energy, Ex from trionic state energy, ET and the biexciton binding energy, Eb,T can be defined as Exx-2Ex [64], where Exx is the biexcitonic state energy. In PL or absorption/reflection spectra, the trion (biexciton) binding energy is typically derived by separating exciton resonance energy from trion (biexciton) resonance energy [65,66,67,68]. Unlike exciton binding, which is strongly influenced by the electron-to-hole effective mass ratio, the energy of trion and biexciton binding is hugely affected by the electron-to-hole effective mass ratio.

Figure 5

(a) Schematic of exciton, trion, biexciton generation in TMDs by photoexcitation. (b) PL and differential reflectance spectra of monolayer TMDs flakes on quartz substrate. (c) The four possible exciton formations in K and K′ valleys. (d) The bound electron-hole pair in exciton picture. [62] Figure reproduced with permission from Elsevier.

2.2. Structural and Optical Characteristics of Graphene Quantum Dots (GQDs)

pan class="Chemical">Graphene quantum dots (GQDs) have attracted a lot of attention as one of the most impn>ortant issues in pan class="Chemical">graphene-based electronics due to the QCE at the nanometer scale, which enables researchers to investigate new structural, optical, and electrical phenomena not seen in other materials [69,70,71,72]. Because of its size-controllable characteristics, graphene may generate tunable light in the visible range at the nanoscale level, which is ideal for optoelectronic device applications. The bandgap of GQDs is proportional to 1/L, where L is the average size of GQDs, and can be regulated up to about 3 eV [73]. The electrons in graphene behave like massless Dirac fermions because their valence and conduction bands overlap at two inequivalent Dirac points and exhibit linear spectra near these points. With significant innovations, different sizes and shapes of graphene, such as hexagonal zigzag, hexagonal armchair, triangular zigzag, and triangular armchair, can now be obtained from bulk material [74]. GQDs’ electronic properties are highly influenced by their size and shape as their bandgaps decrease tediously with increase in number of atoms [75]. Since the absorption edges of GQDs can be configured by varying their sizes, they are especially interesting for light harvesting in photovoltaic devices. Figure 6a shows the HRTEM images of GQDs for their major shapes for a given size (d) of GQDs in percentage (p), where p is defined as the ratio of GQDs with a major shape at each average size [76]. Average sizes of GQDs are being shown using parenthesis in Figure 6a. At d = 5 and 10 nm, circular and elliptical GQDs with average sizes of 5 and 12 nm, respectively, are obtained. At each d, circular GQDs account for more than half of the total number of GQDs in these samples. Circular GQDs disappear at d = 15 nm, leaving only elliptical GQDs with one-third of them deformed. Most GQDs are hexagon-shaped at d = 20 nm, but about a quarter of them are distorted with curved sides. The majority of GQDs are hexagon-shaped at d = 25 nm, with small, irregular-shaped GQDs. Most QDs have rounded vertices and are formed like parallelograms with rectangular shape at d = 35 nm.

Figure 6

(a) HRTEM images of GQDs for their major shapes and corresponding populations (p) with increasing average size of GQDs. (b) Size-dependent PL spectra excited at 325 nm for GQDs of 5–35 nm average sizes in DI water. (c) Dependence of PL peak shifts on the excitation wavelength from 300 to 470 nm for GQDs of 5–35 nm average sizes. [76] Figure reproduced with permission from ACS Publications.

The photoluminepan class="Chemical">scence (pan class="Chemical">PL) characteristics of GQDs have been extensively studied because of their potential applications in optoelectronics field. The PL seen in GQDs is caused by electron-hole pair recombination in quantum-confined GQDs, with the peak energy and shape of the PL spectra highly influenced by the size of the GQDs. Figure 6b shows size-dependent PL spectra excited at 325 nm for GQDs of 5–35 nm average sizes in DI water [76]. The sharp PL peak at 365 nm corresponds to PL generated by DI water [77]. The inset of Figure 6b displays various PL colors for different sizes of GQDs. Regardless of the excitation wavelength, the PL spectra of GQDs with an average size of 17 and 22 nm are resolved in two PL bands, presumably due to the integration of GQDs with various sizes/shapes. In addition, as the excitation wavelength is increased from 300 to 470 nm, the PL peak shifts to longer wavelengths consecutively for all GQD sizes. Figure 6c shows the dependence of PL peak shifts on the excitation wavelength from 300 to 470 nm for GQDs having average size in the rage of 5–35 nm [76]. With the exception of 470 nm, all PL spectra display identical size-dependent peak shifts, regardless of excitation wavelength. As the average size increases up to 17 nm, the PL peak energy drops, confirming the QCE. However, the QCE is no longer relevant for average sizes greater than 17 nm, so the PL peak energy increases with increasing size. As long as GQDs maintain their circular/elliptical form for average sizes less than 17 nm, the PL peak energy decreases with increasing size; however, when the shape of GQDs becomes polygons for average sizes greater than 17 nm, the PL peak energy increases with increasing size as shown in Figure 6a. The development of an excited-state relaxation channel resulting in inelastic light scattering or the alleviation of thermalization due to electron–phonon scattering by using an ultrafast high-power light source have been proposed as explanations for the visible PL contained in graphene sheets. In order to investigate the light emission phenomenon in GQDs, the electronic transitions can be controlled by varying the size/shape of the GQDs while producing strong visible PL emissions. Fast carrier-carrier scattering dominates electron–phonon scattering in GQDs, allowing for direct recombination of excited electron-hole pairs, resulting in high-energy PL in GQDs.

3. Synthesis of 2D-QDs

Synthesis of pan class="Chemical">2D-QDs can be accomplished using one of the two main approaches, top-down and bottom-up approaches. Top-down approaches involve use of physical, chemical electrochemical, and even mechanical methods in order to exfoliate, scale, and decompose bulk materials in well-managed experimental environments for obtaining 2D-QDs. This approach may incorporate intense conditions such as elevated temperatures and chemical reagents such as concentrated acids and strong oxidizing agents. Methods comprising the top-down synthesis approach can sometimes be simpler and cheaper, but it is quite challenging to control the size and shape of 2D-QDs synthesized using these approaches. Bottom-up approaches, on the contrary, implicate synthesis of 2D-QDs with the help of atomic as well as molecular precursors. Bottom-up approaches usually offer better control over size as well as morphology of the 2D-QDs and facilitate efficient utilization of the precursors atoms or molecules. Specific examples on top-down and bottom-up synthesis of 2D-QDs are presented in the following sub-sections.

3.1. Top-down Approaches

Many practical demonstrations of top-down synthesis of pan class="Chemical">2D-QDs can be found in the literature. Qiao et al. prepared 2D-QDs from monolayer molybdenum disulfide (MoS2) using an effective multi-exfoliation method depending on lithium (Li) intercalation [78]. As per the reported demonstration, the monolayer MoS2 was made to undergo the first intercalation by dipping of pristine 2H-MoS2 powder in n-butyl lithium solution in hexane. Filtration and repeated washing with hexane were performed in order to remove excess lithium as well as organic residues and to retrieve the resultant chemical specie, LixMoS2. First, exfoliation was performed immediately after the first inculcation by stirring LixMoS2 in water in an ultrasonic stirrer. Adding hydrochloric acid reduced the pH value of the solution to 2, which made flocculation occur rapidly. The resultant mixture was washed with the water and centrifuged a few times to attain a solution with a pH value of 7 corresponding to the neutral flocculation. The dried, re-stacked MoS2 nanosheets were then made to undergo the second and third exfoliation with Li-intercalation by reiterating the same procedure as mentioned above. Un-exfoliated material was removed by centrifuging the resulting mixture and purification of the mixture was accomplished by removing lithium hydroxide (LiOH) with the help of a dialysis bag. Finally, MoS2 QDs were collected by further centrifuging the mixture and then annealed to obtain enhanced photoluminescence. The complete process to extract 2D-QDs from MoS2 is summarized in Figure 7.

Figure 7

Schematic illustration of the preparation of monolayer MoS2 QDs using multiple exfoliation with Li intercalation [78]. Figure reproduced with permission from Elsevier.

Another top-down approach of synthepan class="Chemical">sizing pan class="Chemical">2D-QDs is reported by Gopalakrishnan et al. who demonstrated synthesis of MoS2 quantum dots interspersed in few-layered sheets of MoS2 [79]. Heterodimensional MoS2 QDs were prepared by incorporating a liquid exfoliation technique in various organic solvents. To briefly describe the experimental approach, MoS2 powder was mixed with 1-methyl-2-pyrrolidone in a container and sonicated with the help of an ultrasonic bath uninterruptedly for a few hours. Then, the resulting dispersion was sonicated with a sonic tip for a few more hours. The dispersion was centrifuged again after keeping undisturbed for a whole night. Temperature was maintained below 277 K by placing the sample in an ice bath. A step-by-step description of the procedure is depicted schematically in Figure 8.

Figure 8

Schematic representation of the synthesis procedure to obtain MoS2 quantum dots interspersed in MoS2 nanosheets using a liquid exfoliation approach. (A) MoS2 QDs formed through sonication bath. (B) MoS2 QDs interspersed in the exfoliated MoS2 nanosheets. [79] Figure reproduced with permission from ACS Publications.

3.2. Bottom-up Approaches

Top-down synthesis apn>proaches, discussed in the previous sub-section, suffer from a few major limitations. These approaches are usually affected by environmental conditions, require expensive and hazardous organic solvents, and ask for intense pretreatment measures. Moreover, it is challenging to precisely control the characteristics and morphology of the 2D-QDs produced using top-down approaches. An alternative method to synthesize 2D-QDs, a so-called bottom-up approach, makes use of atomic or molecular precursors to form the 2D-QDs with desired characteristics. Ideally, bottom-up growth of 2D-QDs (or other low-dimensional nanomaterials) can be prepared with almost infinite number of possible precursors but the challenge in this regard is to develop sufficient understanding of the reaction energetics and precisely control the reaction dynamics [80]. Figure 9a shows schematically how a nanosheet can be grown from molecular precursors, incorporating a bottom-up synthesis approach [81]. Wang et al. report on preparation of MoS2 QDs under hydrothermal conditions by incorporating sodium molybdate and cysteine as precursors [82]. The steps to accomplish the synthesis are summarized as follows: Na2MoO4·2H2O was dissolved in water, pH of the solution was attuned to pH 6.5 with the help of 0.1 M HCl after ultra-sonication, water and L-cysteine were added to the solution followed by a few minutes of sonication, the resulting mixture was then transferred into Teflon-lined stainless steel autoclave and made to react while maintaining the temperature at 200 °C, the solution was cooled in ambient environment, and supernatant containing MoS2 QDs was gathered after a few minutes of centrifugation. The process preparing 2D MoS2 QDs and their use as a sensor for trinitrophenol (TNP) detection is depicted schematically in Figure 9b [82].

Figure 9

(a) Schematic representation of the growth of a nanosheet from molecular precursors [81]. (b) Hydrothermal route for the synthesis of photoluminescent MoS2 quantum dots (QDs) by using sodium molybdate and cysteine as precursors [82]. Figure reproduced with permission from Elsevier and ACS Publications.

In summary, pan class="Chemical">2D-QDs can be prepn>ared upan class="Chemical">sing both top-down and bottom-up approaches while being mindful of the pros and cons of each individual approach. Top-down approaches usually offer the benefit of inexpensive exfoliation targets while bottom-up approaches have potential to create 2D-QDs with well-controlled characteristics. Top-down approaches require intense reaction conditions and strong chemical reagents while bottom-up methods are relatively less mature and more sensitive as well as challenging.

4. Hybrid 2D Quantum Dots Materials and Their Applications

Two-dimenpan class="Chemical">sional QDs such pan class="Chemical">TMDs, GDQs, and others have recently sparked a lot of interest due to their peculiar optical and electronic properties such as tunable energy gaps, effective electronic transport, and semiconducting characteristics [37,83,84,85]. These 2D-QDs have received considerable attention since the advent of graphene and tunable size/shape GQDs and have become a cutting-edge research subject. Owing to their ease of functionalization, 2D-QDs such as TMDs have piqued researchers’ interest for a variety of applications, including transistors, optoelectronic devices, catalysis, energy conversion, batteries, and sensing [41,86,87,88,89,90,91,92,93,94,95,96,97]. Conversely, atomically thin TMDs have low light absorption, so researchers are working on possible strategies to increase the performance of photodetectors based on TMDs. Subsequently, many researchers proposed various nanostructures such as nanobelts, nanorods, and vertically aligned layers to improve the aspect ratio and light-harvesting abilities of TMDs [98,99,100,101,102]. Another important technique for improving photodetection efficiency is to use heterostructure design or nanoparticle decorations [103,104]. Hybridization of colloidal QDs with TMDs has also been investigated by many researchers to improve optical sensing properties [105,106,107,108]. More specifically, if the emission of donor (QDs) and acceptor (TMDs) have spectral overlap during hybridization, a strong dipole–dipole coupling mechanism, NRET (non-radiative energy transfer), will be triggered between them [109,110]. The magnitude of spectral overlap and the separation between donor and acceptor are the two most important factors for determining NRET efficiency. This NRET efficiency implies an increase in energy transfer rate, which explains why QDs/TMD hybrid devices have better photoelectrical performance [111,112].

In this regard, Tang et al. proposed a hybrid 3D nanostructure for opan class="Chemical">ptical senpan class="Chemical">sing and NO2 gas-sensing by integrating colloidal CdS/ZnS or CdSe/ZnS core-shell QDs with 3D WS2 nanowalls [57]. This method transforms a WOx thin film into vertically standing WS2 nanowalls using a quick synthesis method with high heating and cooling rates. Figure 10a depicts an illustration of the WS2 nanowalls synthesis process using the chemical vapor reduction method in a horizontal quartz tube furnace. The sulfurization process started with the WO3/SiO2/Si substrate and sulfur powder as the precursors. After rapid heating to 65 °C and rapid cooling at a rate of approximately 25 °C/min, a high crystal quality WS2 film with 3D nanowall structures was developed, which is confirmed by a series of material characterization. The hybrid structures of QDs and TMDs have already been discussed as a way to improve their individual performance, and it is believed that the QDs/TMDs hybrid device will be a good candidate for various optoelectronic applications. Tang et al. demonstrated an innovative design of a core-shell QDs/WS2 hybrid device for gas sensing applications. The device is assembled in a gas delivery chamber after being bonded to the electrodes on a printed board circuit (PCB) with silver wires to investigate the sensing application. To facilitate effective NO2 gas desorption, a 365 nm UV LED light was installed in the chamber and was continuously switched on and irradiated on the device during measurement. They used a graphene CdSe QDs/WS2 hybrid device in this study because it has the best non-radiative energy transfer efficiency. Figure 10b demonstrates the structural model and p–n junction model of CdSe-ZnS QDs on 3D WS2 nanowalls. During the gas sensing mechanism, the electrons from n-type CdSe-ZnS QDs near the surface tend to diffuse into p-type WS2, while holes from WS2 near the interface diffuse into the surface of CdSe-ZnS QDs. As a result, a space charge carrier diffusion region is formed at the p–n interface as a potential barrier, as shown in the second panel of Figure 10b. When the hybrid device is exposed to NO2, the NO2 molecules interact with the 3D WS2 nanowalls, causing electrons to be extracted from the surface. This will cause the equilibrium in the space charge region to be disrupted, causing electrons from the n-type CdSe-ZnS QDs side to diffuse through the space charge region before a new equilibrium is established [113,114]. As a consequence, the potential barrier’s width would be reduced, increasing the conductivity of the hybrid device and resulting in improved sensing efficiency. For monitoring the gas-sensing properties, the gas delivery chamber was pumped to vacuum and the pumping operation was suspended when NO2 gas was injected into the chamber during the measurements. Figure 10c represents the time-resolved response measurement of NO2 for different concentrations showing the corresponding dynamic NO2-sensing curves. As shown in Figure 10d, the hybrid device demonstrates substantial responses ranging from 40.4% to 95.7% at varying concentrations ranging from 50 parts per billion (ppb) to 1 part per million (ppm), respectively. At an exceptionally low concentration of 50 ppb NO2, the G-CdSe QDs/WS2 device performed admirably. Figure 10e shows the device’s sensing test in a concentration of 50 ppb NO2 gas, which confirmed the device’s strong cycling stability at such a low gas concentration. Figure 10f shows the response and recovery times of the G-CdSe QDs/WS2 gas sensor at a concentration of 1 ppm NO2, suggesting a remarkably quick response time of 26.8 s to achieve the outstanding gas response efficiency of 95.7% and just 187.9 s to return to the restored state. The G-CdSe QDs/WS2 device’s overall gas sensing characteristics are equivalent or even better than those recorded in previous studies for TMD-based and heterostructured gas sensors. In comparison to previously described QDs/TMD thin film device configurations, this hybrid system facilitates the integration of a high-aspect-ratio 3D nanowall structure with the characteristics of nanosized QDs, resulting in a much larger contact area between QDs and TMDs, which can also expedite detecting behaviors. Furthermore, the scalability of this hybrid structure enables the indicated device to have a much wider range of applications in advanced sensing.

Figure 10

(a) Schematic of the synthesis process of WS2 nanowalls by the horizontal furnace. (b) Structural model and p–n junction model of the QDs/WS2 device before and after exposure to NO2 gas. (c) Time-resolved response measurement of NO2. (d) Response of the G-CdSe QDs-WS2 gas sensor as the function of NO2 concentrations. (e) Stability test of the NO2-gas-sensing properties. (f) Rise time and fall time fitting of the G-CdSe QDs-WS2 gas sensor. [57] Figure reproduced with permission from ACS Publications.

In addition to senpan class="Chemical">sing apn>plications, ultrathin monolayer TMDs have significant potential for use in the development of flexible light-emitting devices of mini-scale [115,116,117]. The strong spatial confinement and weak dielectric screening in monolayer TMDs would lead to strong Coulomb interaction and exciton formation with exciton binding energy of about 0.32–0.72 eV [65,118,119]. This high binding energy is responsible for making the excitons effects stable at room temperature, which is favorable for delivering strong light–matter coupling. Plasmonic materials have already been shown to improve luminescence in a number of applications by enabling intense light–matter interactions [120,121]. Plasmonic nanostructures are known to enable high electric field confinement, so they can easily be coupled with 2D TMDs to enhance light absorption and emission. When plasmonic nanostructures and TMDC materials are coupled, a plasmon–exciton coupling effect occurs, resulting in a plexciton that can be used to boost photoluminescence (PL) [122,123,124]. In addition, the plasmonic nanostructures can strengthen the absorption mechanisms of TMD materials as the plasmonic resonance spectrum matches the absorption spectrum of TMDs [125,126]. Chang et al. studied the plasmonic-enhanced PL and color conversion efficiency of a plasmonic nanostructure containing a hybrid 0D core-shell CdSe/ZnS QD/2D monolayer tungsten diselenide (WSe2) semiconductor with an Ag nanodisk (ND) [58]. Plasmonic nanostructure of an Ag ND array was used to enhance the emission from the monolayer WSe2 and improve color conversion from QDs to WSe2. Figure 11a shows the schematic of the QD-Ag-WSe2 hybrid structure with Ag ND patterned on a monolayer WSe2 film that had previously been pre-transferred, and then CdSe QDs were sprayed on top of it. A 5 nm thick alumina (Al2O3) spacer layer was deposited on the interlayers between QD and WSe2 to prevent from PL quenching of the monolayer WSe2 due to charge transfer between WSe2 and Ag ND. The PL intensity of the QD-Ag plasmonic nanostructure was found to be significantly higher than that of CdSe QDs without the Ag ND. The emergence of exciton–plasmon interactions to improve exciton absorption is credited with this PL boost. Furthermore, since the local surface plasmonic resonance (LSPR) spectrum overlapped with the exciton absorption and emission peak of monolayer WSe2, the PL spectrum of Ag-WSe2 hybrid structure was found to be enhanced by an enhancement factor of 1.8. To investigate the light color conversion mechanism from the emission of CdSe QDs to monolayer WSe2, the CdSe QDs and monolayer WSe2 with Ag ND were integrated on a SiO2 substrate. Figure 11b illustrates the PL spectra of the three nanostructure samples with an Ag ND array with a diameter of 123 nm. The orange, red, and green solid lines correspond to the QD-Ag, WSe2-Ag, and QD-Ag-WSe2 nanostructures, respectively. The QD-induced emission from the QD-Ag-WSe2 nanostructure had a considerably lower PL intensity than the QD-Ag nanostructure. The PL intensity of the WSe2 emission in the AgWSe2 nanostructure, on the other hand, was increased after QDs were added. The energy conversion from the QD emission to the WSe2 emission was most likely the cause of this enhancement. The color conversion efficiency (η) from QDs emission to WSe2 emission was estimated for various LSPR wavelength of the Ag ND plasmonic nanostructures as shown in Figure 11c. The coupling of the Ag ND plasmonic nanostructure and the fine-tuning of the Ag nanostructure plasmonic resonant wavelength resulted in a 53% color conversion efficiency from QDs to WSe2. The efficiency was found to decrease with increase in resonant wavelength reaching <1% corresponding to an absorption wavelength of 800 nm. The energy transfer efficiency of bare QD, QD-Ag, and QD-Ag-WSe2 nanostructures was investigated using time-resolved PL with varying Ag ND absorption wavelengths from 500 to 850 nm. Figure 11d illustrates the PL decay curves for the QD peak with Ag ND in the QD, QD-Ag, and QD-Ag-WeS2 structures fitted by a tri-exponential decay at a resonant wavelength of 650 nm. The QDs in the QD-Ag-WSe2 structure have a faster PL decay rate than those in the QD-Ag structure. This faster decay rate of the QDs is attributed to exciton–plasmon coupling effect and PCRET mechanism in the QD-Ag-WSe2 structure. The PL decay rates for QDs in the QD, QD-Ag, and QD-Ag-WSe2 structures were estimated from the TRPL analysis and found to be 0.99 ± 0.03, 1.78 ± 0.05, and 2.38 ± 0.09 ns−1, respectively. The energy transfer rates of the QDs in the QD-Ag-WeS2 structure were obtained using the PL decay rates values and plotted in Figure 11e as a function of the plasmon resonance wavelength of Ag NDs. The energy transfer rate of QDs is found to be dependent on the plasmon resonance wavelength of Ag NDs. Furthermore, the energy transfer rate curves exhibit a similar behavior to the color conversion efficiency curve from QD to WSe2 emission. The energy transfer rate reaches a maximum of 0.16 ns−1, which corresponds to a plasmon resonance wavelength of 650 nm. Subsequently, hybrid QD/TMD light emitters can be coupled with GaN-based white LEDs to improve color temperature and broaden the color gamut of a miniature white LED.

Figure 11

(a) Hybrid zero-dimensional core–shell CdSe/ZnS quantum dot (QD)/two-dimensional monolayer WSe2 semiconductors with an Ag nanodisk (ND). (b) PL spectra of the three samples. (c) Energy conversion efficiency from the CdSe QD to WSe2. (d) PL decay curves of the QD peak (630 nm) in the QD, QD−Ag, and QD−Ag−WSe2 structures with an Ag ND. (e) Energy transfer rate of QD in the QD−Ag−WSe2 structure [58]. Figure reproduced with permission from ACS Publications.

It has previously been stated that compan class="Chemical">bining QDs and pan class="Chemical">TMDs would result in improved photoelectrical performance due to the coupling mechanism and high energy transfer rate. Two-dimensional TMDs have been opted for photodetector or phototransistor due to its suitable bandgap and high carrier transport mobility [42,127]. As a result, it is anticipated that combining QDs and 2D materials would dramatically improve photodetectors’ performance. Hybrid QDs/graphene phototransistors have been demonstrated to have high responsivity owing to the photogating effect caused by capacitive coupling [128]. Most graphene-based devices, on the other hand, have a high dark current and a slow response time due to the presence of semimetal channels [129,130,131,132]. To address these issues, a 2D MoS2 channel has been used to develop a QDs/MoS2 hybrid phototransistor, which suppressed dark current and improved response time [133]. Because of its proper bandgap values (direct bandgap of 1.6 eV in single layer form and indirect bandgap of 1.3 eV in bulk form), large surface-to-volume ratio, and high mobility, WSe2 is ideal for optoelectronic applications. Hu et al. designed hybrid phototransistors for high performance and broadband detection using high transport mobility p-type 2D WSe2 and PbS QDs [56]. Figure 12a depicts the device structure of the PbS QD-capped hybrid back-gate WSe2 phototransistor. The transistor channel, which has a width of about 10 m, is made of monolayer WSe2 grown by chemical vapor deposition. A thermal evaporation method with a shadow mask has been used to deposit gold (Au) electrodes (source and drain) of about 100 nm. Colloidal PbS QDs were spin-coated on a WSe2 nanosheet device to create the hybrid device, and the coated QDs ligands had to be replaced later with tetrabutylammonium iodide (TBAI). The photocarrier transport mechanism in the hybrid photodetector under infrared (IR) illumination is shown in Figure 12b. Under illumination, photoexcited carriers are generated at the PbS QDs layer and the built-in potential between the PbS QDs and WeS2 monolayer separates the carriers at the p–n junction. The photogenerated holes will be moved from PbS QDs to WSe2 monolayer under an applied electric field, VDS, while electrons will remain accumulated in the PbS QDs layer. These electrons can efficiently gate the WSe2 nanosheet by functioning as a photogating component through capacitive coupling and help in regulating device conduction. The hybrid phototransistor’s system output has been investigated, and it has been discovered that it inherited the wide spectral detection due to the broad absorption of PbS QDs. Figure 12c represents the wavelength dependence response curve of the hybrid phototransistor with under-applied voltage of 1 V at back-gate voltage (VGS = 0 V). The response peak at 970 nm corresponds to the first exciton peak. By varying the size of PbS QDs, it is possible to achieve wavelength selectivity and a wide photoresponse for UV–vis–NIR detection. The specific detectivity (D*) of the hybrid phototransistor has also been investigated and plotted in Figure 12d as a function of back-gate voltage under 970 nm illumination. At all back-gate voltage ranges, the specific detectivity could reach 1013 Jones, regardless of whether the back-gate was in the ON or OFF state. Figure 12e shows the responsivity and specific detectivity curves as a function of VDS at VGS = 0 V. The high responsivity of the hybrid photodetector is attributed to the superior detectivity properties. The responsivity as well as the specific detectivity increase with increasing applied field at VGS = 0 V with an estimated maximum value of about 7 × 105 AW−1 and 7 × 1013 Jones, respectively, which is superior to other TMDs-based photodetectors. Future optoelectronic devices may benefit from this current device construction strategy, improved photogating performance, and stable device operating conditions.

Figure 12

(a) Schematic diagram of back-gate WSe2 phototransistor device capped by PbS QDs. (b) Schematic description for the photocarrier transport in hybrid phototransistor under illumination. (c) Wavelength dependence response curve of the hybrid phototransistors with VDS = 1 V. (d) Specific detectivity as a function of gate voltage at VDS = 1 V. (e) Responsivity and detectivity as a function of VDS (VGS = 0 V). [56] Figure reproduced with permission from John Wiley and Sons.

Apan class="Chemical">side from pan class="Chemical">TMDs, graphene QDs has shown to have unique properties for ultrafast photodetectors due to its high charge carrier mobility, thin profile, tunable optical properties, wavelength-dependent absorption, and strong absorption spectrum [134,135,136]. The ultrafast conversion of photons to currents in ultrafast photodetectors is specifically driven by high carrier mobility. Previous research has shown that the most sensitive graphene-based photodetectors require the inclusion of an electrically passive sensitizing layer made up of colloidal QDs (CQDs), perovskites, carbon nanotubes, or 2D materials [128,129,137,138]. Since graphene has zero bandgap, it can generate charge carriers by light absorption across a broad energy spectrum. Furthermore, graphene enables wafer-scale integration by low-cost manufacturing based on complementary metal-oxide-semiconductor (CMOS) fabrication processes. The graphene photodetectors have the advantage of being compatible with standard photonic integrated circuits in terms of the manufacturing process. Unfortunately, graphene photodetectors have low sensitivity and broad dark currents due to biasing of the graphene channel or fabrication method [139,140,141,142,143,144]. As a result, developing a better photodetector configuration that can fully exploit graphene’s properties is a top priority. In this regard, Nikitskiy et al. addressed the challenges by demonstrating a hybrid photodetector device by integrating a CQD photodiode atop a high-gain graphene phototransistor [145]. The carrier drift in the photodiode due to electric field can dramatically increase charge collection by altering the electrically passive sensitizing layer to an active one. Figure 13a illustrates the optical image of the hybrid graphene transistor–CQD photodiode detector, as well as the electrodes used. The device is made up of a graphene channel on top of which is deposited a patterned 300 nm thick CQD film, which is then overcoated with an ITO electrode’s top-contact. In the region where the three layers overlap, the photodetector’s active area is created. The CQD layer is patterned to prevent charge carriers from escaping to the drain contacts, thus obviating the need for graphene. This four-terminal sensing device is being designed to eliminate the contact resistance and isolate measurement only over the photodetector’s active region. Figure 13b shows the phototransistor operation as well as the illustration of the electronic circuit. When light is incident on the device, electron-hole pairs are generated in the CQD layer drifted by the built-in electric field at the interface and by the bias applied across the diode. Electrons will continue to remain in the CQD, while holes will diffuse to the graphene channel, changing its resistance due to depletion at the interface. A voltage drop is estimated between V+ and V− electrodes, while a constant current is driven between source and drain electrodes. Without accounting for the resistance of the metal and graphene contacts, the photo-induced change in resistance or voltage drop can be measured with the highest accuracy. The responsivity and EQE of the indicated device were measured and plotted in Figure 13c as a function of applied top-contact bias (VTD). The responsivity of the phototransistor is measured to be 5 × 108 VW−1 at VTD of 1.2 V corresponding to bias current of 100 µA. The EQE is found to be dependent on VTD as shown in Figure 13c, where it increases and saturates after certain VTD value. Without any bias, EQE is about 10%, and it increases with VTD to about 75% at 1.2 V reverse bias, where it saturates. This is due to the fact that as VTD increases, the depletion region expands, improving charge collection efficiency. The carrier lifetime of the hybrid photodetector has been estimated from the photoresponse bandwidth shown in Figure 13d. The electrical 3dB bandwidth of the photodetector can reach a maximum value of 1.5 kHz and was found to be increasing with increasing VTD, as shown in the inset of Figure 13d. The extracted effective lifetime of the photodetector is 106 µs corresponding to 1.5 kHz bandwidth. In addition, the photoconductive gain has been estimated using decay components and found to be on the order of 105, with a gain-bandwidth product of >1.5 × 108 Hz. Figure 13e illustrates the photoresponse of the photodetector expressed in terms of ΔV as a function of incident irradiance. The lowest observable irradiance was estimated to be 10−5 Wm−2 at a VTD of 1.2 V, with the detector’s linear dynamic range increasing as VTD values increased. The inset of Figure 13e demonstrates the linearity of photoresponse for high irradiance values. The photoresponse is observed to increase as the incident irradiance value increases, being saturated at a power density of 0.5 Wm−2. Figure 13f shows the measured responsivity of the detector in terms of VW−1 and AW−1 as a function of incident irradiance. The high linear dynamic range achieved by using a photodiode rather than a passive sensitizer is demonstrated by the flat responsivity responses over a broad range of power density. Using a photodiode instead of a passive sensitizing layer allows for a much wider range of output parameters. Finally, this hybrid design demonstrates graphene’s and other two-dimensional materials’ ability to be effectively combined with other optoelectronic materials, paving the way for hybrid 2D/0D optoelectronics.

Figure 13

(a) Optical image of the hybrid graphene transistor-CQD photodiode detector. (b) Schematic of phototransistor operation. (c) Responsivity and EQE of the visible/near-infrared phototransistor. (d) Normalized photoresponse as a function of light modulation frequency. Inset: extracted 3 dB bandwidth values. (e) Photo-induced signal as a function of incident irradiance, inset demonstrates the linearity of photoresponse for high irradiance values. (f) Measured responsivity of the detector in VW−1 (left axis) and responsivity converted in AW−1 (right axis). [145] Figure reproduced with permission from Springer Nature.

Min et al. reported another hybrid structure compripan class="Chemical">sing zero-dimensional (0D) GQDs and semiconducting 2D MoS2 that exhibits remarkable properties for optoelectronic devices, outperforming MoS2 photodetectors [146]. GQDs exhibit unique optoelectronic features such as long carrier lifetimes and rapid electron extraction due to enormous transition energies and weak coupling to excitonic states. When GQDs interact with 2D materials, quantum effects can influence charge carrier dynamics, allowing for charge transfer, carrier separation, and collection. The hybrid GQD/MoS2 photodetectors were made by drop-casting the GQDs solution over bulk mechanically exfoliated MoS2 membranes on SiO2/Si substrates, as shown in Figure 14a. The insets of Figure 14a depict the corresponding molecular structures of GQDs (top view) and MoS2 (side view). The photoelectrical mechanism of this device consists of different photo-physical steps—photoexcitation, re-absorption, tunneling, and thermal excitation. When the energy of the incoming photon source exceeds the bandgap of GQDs, photoexcitation occurs in MoS2 and GQDs. A re-absorption process of emitted photons from GQDs by MoS2 is then detected, thereby increasing the photocurrent by generating more electron-hole pairs. Following that, photoexcited electrons in the conduction band of GQDs are injected into MoS2 to initiate a tunneling process. Similarly, holes from MoS2’s valence band will be transferred to GQDs, resulting in a higher rate of recombination. Finally, the Schottky barrier formation at the interface of GDQs and MoS2 leads to thermal excitation of higher-energy electrons from GQDs to MoS2. As a result of the multiple charge carrier amplification processes, the photoresponse of hybrid GQD/MoS2 devices will be higher than bare MoS2 devices. Using a tunable laser source for optical illumination, the photoresponse of the hybrid GQD/MoS2 and bare MoS2 devices as a function of wavelength has been analyzed, as shown in Figure 14b. The photoresponsivity of the hybrid GQDs/MoS2 was found to be 775 AW–1 at a laser wavelength of 400 nm, whereas the photoresponsivity of bare MoS2 was found to be 44.8 AW–1. In comparison to previous photodetector studies based on other material systems such as CuPc and CdTe, the experimentally determined photoresponsivity is over 300 times higher [147,148]. Furthermore, the GQD/MoS2 hybrid device exhibits a detectivity of 2.33 × 1012 Jones and an EQE (~241%) of almost 17 times higher than that of the bare MoS2 device (~14%).

Figure 14

(a) Schematic of the hybrid GQD/MoS2 device under optical illumination. (b) Photoresponsivity of hybrid GQD/MoS2 and the bare MoS2 devices. [146] Figure reproduced with permission from ACS Publications.

Two-dimenpan class="Chemical">sional pan class="Chemical">TMDs with substantial spin–valley coupling, which introduce a significant coupling between the spin and valley degrees of freedom, have recently attracted a lot of attention for prospective applications in spintronics, valleytronics, and other fields. Furthermore, earlier research has revealed that the lack of interlayer interaction causes an indirect-to-direct bandgap transition in monolayered WS2 sheets [149,150]. Because of the strong spin–valley coupling and the presence of a direct bandgap in monolayered WS2 sheets, they can be used in optoelectronics, spintronics, valleytronics, and other fields [151,152,153]. Due to the strong quantum confinement effect, monolayered WS2 QDs can display more remarkable features than monolayered sheets, which strengthens the spin–valley coupling and widens the bandgap. Zhang et al. demonstrated ultrasmall and monolayered WS2 QDs with giant spin–valley coupling and purple luminescence [154]. Three absorption peaks are observed on monolayered WS2 sheets: 625 nm, 550 nm, and 450 nm. The absorption peaks at 625 and 550 nm are due to transition from the spin-splitting valence band to the conduction band at the K point of the Brillouin zone while the optical transition between the density-of-state peaks in the valence and conduction bands causes the absorption peak at 450 nm. However, for annealed WS2 QDs, three exciton absorption peaks at A (379 nm), B (303 nm), and C (269 nm) are observed. The large energy differential between the A and B excitonic absorption peaks in annealed WS2 QDs is discovered to be up to 821 meV, implying the presence of a huge spin–valley coupling. The annealed WS2 QDs have two unique emission peaks at 416 and 342 nm, corresponding to A and B emission peaks. It is obvious that the significant quantum confinement effect will undoubtedly enhance the spin–valley coupling and increase the bandgap of QDs. As a result, the ultrasmall lateral size could be responsible for both the enormous energy difference between the two absorption peaks and the purple PL in annealed WS2 QDs. Moreover, there is no spin–orbit splitting in WS2 QDs and this suppression in the intervalley scattering is also responsible for the giant spin–valley coupling.

Table 1 summarizes the performance of pan class="Chemical">2D-QDs-based devices used in this review.

Table 1

Performance of 2D-QDs-based devices.

Device Structure	Performance	References
Core-shell QDs/WS2 hybrid device for gas sensing	The hybrid device demonstrates an outstanding NO2 gas-sensing performance with a remarkably quick response time of 26.8 s to achieve the outstanding gas response efficiency of 95.7%.	[57]
CdSe/ZnS QD-Ag-WSe2	The Ag ND was combined with CdSe QDs and monolayer WSe2 to enhance the monolayer WSe2 emission and convert the light from QDs to WSe2 with the highest efficiency of 53%.	[58]
Hybrid PbS QDs/WSe2	The hybrid device demonstrated a high responsivity up to 2 × 105 A W–1 and a high specific detectivity of 7 × 1013 Jones.	[56]
PbS QDs photodiode atop a high-gain graphene phototransistor	The device demonstrated quantum efficiencies in excess of 70%, gain of 105, and 3 dB bandwidth of 1.5 kHz with a measured detectivity of 1 × 1013 Jones.	[145]
GQD/MoS2 hybrid photodetector	The device exhibits a photoresponsivity 775 AW–1 at a laser wavelength of 400 nm, a detectivity of 2.33 × 1012 Jones, and an EQE of about 241%.	[146]
WS2 QDs for spintronics and valleytronics	Ultrasmall and monolayered tungsten dichalcogenide QDs with giant spin–valley coupling and purple luminescence for various applications in spintronics and valleytronics.	[154]

There are numerous pros and cons to empan class="Chemical">ploying pan class="Chemical">2D-QDs in several electrical and optical systems. Two-dimensional materials have been extensively explored as channel materials for future electronic device applications due to their atomically thin structure and superior electrostatic control, which enhances immunity to short channel effects and the loss of band-edge sharpness. With the number of stacked layers and the amount of strain, the bandgap and mobility of these materials changes. On the one hand, being able to tune channel attributes makes many circuit design challenges easier to solve. However, uncontrolled variation might lead to catastrophic yield consequences. Two-dimensional materials are excellent choices for optoelectronic devices owing to their unique features, such as a wide response spectrum, exceptional flexibility, and strong light–matter interaction. Additionally, 2D heterostructure-based optoelectronic memory device capable of accumulating and releasing photo-generated carriers under the influence of an electric field and light irradiation can be developed. Because of the emergence of 2D materials, miniature, flexible, and low-energy optoelectronic storage systems are now possible. Due to their strong charge mobility and moderate bandgaps, field-effect transistors (FETs) have been made from a range of semiconducting 2D materials such as TMDs and black phosphorus, making them suitable candidates for this application. The intrinsic flexibility of 2D materials is an advantage, as they may be used to produce flexible circuits when combined with suitable substrates. Many TMDCs (such as MoS2, MoSe2, WS2, and WSe2) and black phosphorus have a bandgap in the optical or near-infrared range and good charge transport properties, making them ideal for high-efficiency photodetectors. Two-dimensional materials have exceptional spin-valley characteristics, allowing for spin injection, manipulation, and detection in a single integrated device, resulting in scalable and ultrafast nonvolatile logic circuits with extremely low energy dissipation. TMDs with a direct bandgap allow circularly polarized light to excite carriers preferentially within a given valley with a specified valley pseudospin. Unfortunately, there are a number of challenges that limit the use of single 2D materials. When metal electrodes are directly deposited on 2D semiconductors during device manufacturing, a Schottky barrier comes into existence, resulting in high contact resistance. Furthermore, due to their short lifetime, intralayer excitons formed in single 2D semiconductor materials are challenging to handle, limiting their use in exciton devices. Most insulated 2D materials, including hBN, are not acceptable for use in devices on their own, and BP is readily oxidized when exposed to air. In the following section, we go over these problems in greater detail.

5. Challenges Faced by 2D-QDs Materials

Despite recent accomplishment in this fan>an class="Chemical">scinating research area, there are several crucial challenges to be taken into consideration.

5.1. Synthesis/Deposition of 2D-QDs Materials

The first challenge concerns the synthesis of pan class="Chemical">crystalline 2D materials, including the control of their crystalline phases, grain size, grain boundaries, and morphology. The structure characteristics play a very prominent role in the chemical and physical properties of 2D materials. Therefore, a sagacious structure of interface layer synthesis is vital. Consequently, the structure of 2D materials extremely depends on the physical and chemical properties of the precursors, such as solubility, thermal stability, sensitivity, catalytic activity. For a better understanding of the crystal growth mechanism, the structure characterization at the atomic level is a critical challenge. Several in situ characterization techniques such as in situ XRD and TEM have been developed in the past few years. However, expeditiously observing the growth of 2D materials using these techniques is not quite facile. For exemplification, the formation of 2D materials at the interfaces due to the assemblage of the precursor is still inconclusive by TEM caused by sensitivity to electron irradiation [155]. Moreover, the adequately low mechanical and chemical stability causes the defect during the transfer process of 2D materials. Furthermore, some air-sensitive 2D materials in the ambient atmosphere cause possible oxidation, which leads to the structure rottenness. Additionally, it is very difficult to transfer the 2D materials synthesized on the solid substrates [156].

5.2. Transfer Process

The chemical vapor depopan class="Chemical">sition technique is tremendously used to grow high surface area and the controlled layer of pan class="Chemical">2D materials on donor substrate, which is a promising functional material for conductors, semiconductors, and insulators in the photodetector, RRAM, gas sensors, flexible, and transparent devices [35]. In several cases, 2D materials must be transferred from a donor substrate to a target substrate; however, there are high possibilities of damaging 2D materials during the transfer process and as a consequence of chemical doping, contamination, and tearing. For the high-performance commercial application, 2D materials should have a high surface area, damage-free structure, and high mechanical and chemical stability. However, a transfer process to overcome all challenges and has still not been developed. Despite this, the transfer process is classified into four parts: wet transfer, dry transfer, mechanical transfer, and electro-chemical transfer [157]. However, the wet transfer process is the most common and widely used process to transfer 2D materials [158]. This process uses polymethyl methacrylate (PMMA) as a transfer film. PMMA plays an extremely significant role in protecting the material from physical damage. It was reported that large surface area 2D material with 4-inch wafer size could be transferred onto desired target substrate using the wet transfer process [159]. After the transfer process, PMMA is difficult to completely remove from the target substrate, which can cause degenerateness of electrical and optical properties of the photodetector fabrication with 2D material. To overcome this challenge and completely remove the PMMA from the material and improve the electrical and optical properties, additional etching and high-temperature annealing have been suggested [160].

5.3. The Schottky Barrier

One of the pan class="Chemical">biggest issues confronting pan class="Chemical">2D materials-based devices is the presence of a Schottky barrier (SB) at the interface between the material and the contact metal electrode. However, the potential energy barrier for electrons formed at the Schottky junction, known as the Schottky barrier height, blocks the flow of charge carriers into the device channel [161]. Subsequently, this prominent Schottky barrier height led to large contact resistance and performance degradation in two-terminal devices [162]. It has been suggested to tune the Schottky barrier by reducing fermi level pinning leads for better performance of devices. Zhou et al. reported the use of graphene as the metal electrode, which comes into contact with single layer of the SnSe sheet to form a van der Waals (vdW) heterojunction. After theoretical calculations, they found that the fermi level pinning is reduced because of the interaction between the SnSe layer and graphene and intrinsic properties of SnSe sheet are protected. Usually, charge carriers move from the source to the channel zone, then they conflict with two energy barriers, one of being the Schottky barrier (ΦSB⊥), which can be found at the vertical interface of the contact and used to transport the charge carrier across the interface of the SnSe/G heterojunction, and the other one arises at the lateral interface contact and the channel part characterized by band bending, ΔEF. These parameters are extremely prominent and inconclusive to the performance of transistors [163].

6. Conclusions and Future Outlook

Two-dimenpan class="Chemical">sional QDs are inpan class="Chemical">creasingly being touted as promising materials due to their fascinating properties (such as full color PL spectrum, high solubility, bandgap tunability, high selectivity to special molecules, and ease of surface functionalization) and widespread applications in sensors, batteries, WLEDs, photodetectors, phototransistors, etc. Despite their great potential for optoelectronics applications, as described in this review article, they encounter a series of daunting obstacles that must be overcome before their commercialization. The emergence of double element QDs, as well as their heteroatom-doped variants, has yet to be thoroughly investigated, both in terms of synthesis and fundamental property evaluation. Several mechanisms in terms of PL improvement, surface passivation, structure optimization, manufacturing aspects, and so on have yet to be established. To fulfill the standards for industrial-scale applications or commercialization, the current output, performance, quantity, and productivity of 2D-QDs must be monitored. Furthermore, energy conversion and storage based on 2D-QDs materials are still in the early stages of development. Because of their relatively low physical and chemical stability, most 2D-QDs currently suffer from long-term stability and durability problems, which must be addressed in the future for practical applications. When 2D-QDs are used as fluorescent active materials, their low quantum yield and wide emission band can pose a problem when compared to conventional fluorophores.