Sébastien Ruiters1, Sohaib Shujaat2,3, Karla de Faria Vasconcelos2, Eman Shaheen2,3, Reinhilde Jacobs2,3,4, Ilse Mombaerts1. 1. Department of Ophthalmology, University Hospitals Leuven, Leuven, Belgium. 2. OMFS - IMPATH Research Group, Department of Imaging and Pathology, Faculty of Medicine, Catholic University Leuven, Leuven, Belgium. 3. Department of Oral and Maxillofacial Surgery, University Hospitals Leuven, Leuven, Belgium. 4. Department of Dental Medicine, Karolinska Institutet, Huddinge, Sweden.
Abstract
PURPOSE: Fitting a customized ocular prosthesis for anophthalmic patients entails an artisanal labour-exhausting process and is standardly based on impression moulding of the socket, which may be anatomically inaccurate. The objective of the study was to design an impression-free socket mould with three-dimensional (3D) technology. METHODS: The ex vivo anophthalmic socket models included one silicone, one fresh pig cadaver head and three fresh-frozen human cadaver heads. After intra-socket application with iodine substance, five observers obtained eighteen low-dose cone beam computed tomography (CBCT) scans and one observer one high-dose CBCT scan of each model. The observers designed non-impression 3D moulds of the socket with 3D software. For the human cadaver sockets 3D geometric models of the ocular prosthesis were rendered from the 3D mould of the socket and the mirrored cornea of the contralateral eye. RESULTS: The posterior surface of the 3D mould was highly accurate, with a mean absolute deviation of 0.28 mm, 0.53 mm, 0.37 mm and mean upper deviation of 0.53 mm, 0.86 mm, 1.17 mm, respectively, for the phantom, pig and human model. The intra- and interobserver repeatability and reproducibility of the 3D moulds and designs was good (<0.35 mm). The largest variation in the 3D geometric model was found at the junction of the 3D mould and mirrored cornea. CONCLUSION: 3D design of an impression-free geometric model for an ocular prosthesis with low-dose CBCT is highly accurate in ex vivo anophthalmic socket models. This novel method is a critical step towards the manufacturing of 3D printed ocular prostheses and requires validation in anophthalmic patients.
PURPOSE: Fitting a customized ocular prosthesis for anophthalmic patients entails an artisanal labour-exhausting process and is standardly based on impression moulding of the socket, which may be anatomically inaccurate. The objective of the study was to design an impression-free socket mould with three-dimensional (3D) technology. METHODS: The ex vivo anophthalmic socket models included one silicone, one fresh pig cadaver head and three fresh-frozen human cadaver heads. After intra-socket application with iodine substance, five observers obtained eighteen low-dose cone beam computed tomography (CBCT) scans and one observer one high-dose CBCT scan of each model. The observers designed non-impression 3D moulds of the socket with 3D software. For the human cadaver sockets 3D geometric models of the ocular prosthesis were rendered from the 3D mould of the socket and the mirrored cornea of the contralateral eye. RESULTS: The posterior surface of the 3D mould was highly accurate, with a mean absolute deviation of 0.28 mm, 0.53 mm, 0.37 mm and mean upper deviation of 0.53 mm, 0.86 mm, 1.17 mm, respectively, for the phantom, pig and human model. The intra- and interobserver repeatability and reproducibility of the 3D moulds and designs was good (<0.35 mm). The largest variation in the 3D geometric model was found at the junction of the 3D mould and mirrored cornea. CONCLUSION: 3D design of an impression-free geometric model for an ocular prosthesis with low-dose CBCT is highly accurate in ex vivo anophthalmic socket models. This novel method is a critical step towards the manufacturing of 3D printed ocular prostheses and requires validation in anophthalmic patients.
Authors: Georges E Daoud; Dante L Pezzutti; Calvin J Dolatowski; Ricardo L Carrau; Mary Pancake; Edward Herderick; Kyle K VanKoevering Journal: J Mater Res Date: 2021-07-06 Impact factor: 3.089