Hu Chen1, Hong Li2, Yijiao Zhao3, Xinyue Zhang3, Yong Wang4, Peijun Lyu5. 1. Doctor and Researcher, Center of Digital Dentistry & National Engineering Laboratory for Digital and Material Technology of Stomatology, Peking University School and Hospital of Stomatology, Beijing, PR China. 2. Resident, First Clinical Division, Peking University School and Hospital of Stomatology, Beijing, PR China. 3. Engineer, Center of Digital Dentistry & National Engineering Laboratory for Digital and Material Technology of Stomatology, Peking University School and Hospital of Stomatology, Beijing, PR China. 4. Professor, Center of Digital Dentistry & National Engineering Laboratory for Digital and Material Technology of Stomatology, Peking University School and Hospital of Stomatology, Beijing, PR China. 5. Professor, Center of Digital Dentistry & National Engineering Laboratory for Digital and Material Technology of Stomatology, Peking University School and Hospital of Stomatology, Beijing, PR China. Electronic address: kqlpj@bjmu.edu.cn.
Abstract
STATEMENT OF PROBLEM: Selective laser melting (SLM) is a novel 3-dimensional (3D) printing technology that can directly form the metal frameworks of removable partial dentures. The adaptation of SLM frameworks has not been thoroughly evaluated. PURPOSE: The purpose of this in vitro study was to evaluate the tissue surface adaptation of removable partial denture frameworks fabricated by an SLM technique. MATERIAL AND METHODS: Four types of maxillary partial edentulous resin models were custom made: bilateral second premolars and molars missing, bilateral premolars and first molars missing, all teeth missing except 2 canines, and 2 central incisors missing. According to these dentition-defect patterns, 4 types (I, II, III, and IV) of virtual removable partial denture frameworks were designed, and an SLM printer was used for 3D printing using cobalt-chromium (Co-Cr) alloys (repeated 3 times). As a control, refractory casts duplicated from the resin models were used to fabricate denture frameworks by the lost-wax casting technique. Average gaps and maximum gaps between frameworks and models were measured using the silicone impression material. Two-way ANOVA was used to determine the influence of production methods and design types on the gaps (α=.05). RESULTS: The 2-way ANOVA showed that average gaps were significantly influenced by the production methods and design types, as well as their interactions (P<.001). With design Types I and II, the average gaps of the SLM-printed frameworks were larger than those of the cast ones (P<.001). However, no such differences were found for design Type III, P=.325, or IV, P=.862. CONCLUSIONS: SLM-printed frameworks achieved an acceptable adaptation. However, among frameworks with a large span and relatively more retainers and clasps, the adaptation of those made by the precision casting technique was slightly better than that of those printed by the SLM technique.
STATEMENT OF PROBLEM: Selective laser melting (SLM) is a novel 3-dimensional (3D) printing technology that can directly form the metal frameworks of removable partial dentures. The adaptation of SLM frameworks has not been thoroughly evaluated. PURPOSE: The purpose of this in vitro study was to evaluate the tissue surface adaptation of removable partial denture frameworks fabricated by an SLM technique. MATERIAL AND METHODS: Four types of maxillary partial edentulous resin models were custom made: bilateral second premolars and molars missing, bilateral premolars and first molars missing, all teeth missing except 2 canines, and 2 central incisors missing. According to these dentition-defect patterns, 4 types (I, II, III, and IV) of virtual removable partial denture frameworks were designed, and an SLM printer was used for 3D printing using cobalt-chromium (Co-Cr) alloys (repeated 3 times). As a control, refractory casts duplicated from the resin models were used to fabricate denture frameworks by the lost-wax casting technique. Average gaps and maximum gaps between frameworks and models were measured using the silicone impression material. Two-way ANOVA was used to determine the influence of production methods and design types on the gaps (α=.05). RESULTS: The 2-way ANOVA showed that average gaps were significantly influenced by the production methods and design types, as well as their interactions (P<.001). With design Types I and II, the average gaps of the SLM-printed frameworks were larger than those of the cast ones (P<.001). However, no such differences were found for design Type III, P=.325, or IV, P=.862. CONCLUSIONS: SLM-printed frameworks achieved an acceptable adaptation. However, among frameworks with a large span and relatively more retainers and clasps, the adaptation of those made by the precision casting technique was slightly better than that of those printed by the SLM technique.
Authors: Naseer Ahmed; Maria Shakoor Abbasi; Sara Haider; Nimra Ahmed; Syed Rashid Habib; Sara Altamash; Muhammad Sohail Zafar; Mohammad Khursheed Alam Journal: Biomed Res Int Date: 2021-09-06 Impact factor: 3.411