Donald R Hume1, Alessandro Navacchia1, Azhar A Ali1, Kevin B Shelburne2. 1. University of Denver, Center for Orthopaedic Biomechanics, Denver, CO, United States. 2. University of Denver, Center for Orthopaedic Biomechanics, Denver, CO, United States. Electronic address: Kevin.Shelburne@du.edu.
Abstract
INTRODUCTION: Musculoskeletal modeling allows insight into the interaction of muscle force and knee joint kinematics that cannot be measured in the laboratory. However, musculoskeletal models of the lower extremity commonly use simplified representations of the knee that may limit analyses of the interaction between muscle forces and joint kinematics. The goal of this research was to demonstrate how muscle forces alter knee kinematics and consequently muscle moment arms and joint torque in a musculoskeletal model of the lower limb that includes a deformable representation of the knee. METHODS: Two musculoskeletal models of the lower limb including specimen-specific articular geometries and ligament deformability at the knee were built in a finite element framework and calibrated to match mean isometric torque data collected from 12 healthy subjects. Muscle moment arms were compared between simulations of passive knee flexion and maximum isometric knee extension and flexion. In addition, isometric torque results were compared with predictions using simplified knee models in which the deformability of the knee was removed and the kinematics at the joint were prescribed for all degrees of freedom. RESULTS: Peak isometric torque estimated with a deformable knee representation occurred between 45° and 60° in extension, and 45° in flexion. The maximum isometric flexion torques generated by the models with deformable ligaments were 14.6% and 17.9% larger than those generated by the models with prescribed kinematics; by contrast, the maximum isometric extension torques generated by the models were similar. The change in hamstrings moment arms during isometric flexion was greater than that of the quadriceps during isometric extension (a mean RMS difference of 9.8 mm compared to 2.9 mm, respectively). DISCUSSION: The large changes in the moment arms of the hamstrings, when activated in a model with deformable ligaments, resulted in changes to flexion torque. When simulating human motion, the inclusion of a deformable joint in a multi-scale musculoskeletal finite element model of the lower limb may preserve the realistic interaction of muscle force with knee kinematics and torque.
INTRODUCTION: Musculoskeletal modeling allows insight into the interaction of muscle force and knee joint kinematics that cannot be measured in the laboratory. However, musculoskeletal models of the lower extremity commonly use simplified representations of the knee that may limit analyses of the interaction between muscle forces and joint kinematics. The goal of this research was to demonstrate how muscle forces alter knee kinematics and consequently muscle moment arms and joint torque in a musculoskeletal model of the lower limb that includes a deformable representation of the knee. METHODS: Two musculoskeletal models of the lower limb including specimen-specific articular geometries and ligament deformability at the knee were built in a finite element framework and calibrated to match mean isometric torque data collected from 12 healthy subjects. Muscle moment arms were compared between simulations of passive knee flexion and maximum isometric knee extension and flexion. In addition, isometric torque results were compared with predictions using simplified knee models in which the deformability of the knee was removed and the kinematics at the joint were prescribed for all degrees of freedom. RESULTS: Peak isometric torque estimated with a deformable knee representation occurred between 45° and 60° in extension, and 45° in flexion. The maximum isometric flexion torques generated by the models with deformable ligaments were 14.6% and 17.9% larger than those generated by the models with prescribed kinematics; by contrast, the maximum isometric extension torques generated by the models were similar. The change in hamstrings moment arms during isometric flexion was greater than that of the quadriceps during isometric extension (a mean RMS difference of 9.8 mm compared to 2.9 mm, respectively). DISCUSSION: The large changes in the moment arms of the hamstrings, when activated in a model with deformable ligaments, resulted in changes to flexion torque. When simulating human motion, the inclusion of a deformable joint in a multi-scale musculoskeletal finite element model of the lower limb may preserve the realistic interaction of muscle force with knee kinematics and torque.
Authors: Apoorva Rajagopal; Christopher L Dembia; Matthew S DeMers; Denny D Delp; Jennifer L Hicks; Scott L Delp Journal: IEEE Trans Biomed Eng Date: 2016-07-07 Impact factor: 4.538
Authors: Niccolo M Fiorentino; Jonathan S Lin; Kathryn B Ridder; Michael A Guttman; Elliot R McVeigh; Silvia S Blemker Journal: J Biomech Eng Date: 2013-04 Impact factor: 2.097
Authors: Azhar A Ali; Sami S Shalhoub; Adam J Cyr; Clare K Fitzpatrick; Lorin P Maletsky; Paul J Rullkoetter; Kevin B Shelburne Journal: J Biomech Date: 2015-12-21 Impact factor: 2.712
Authors: Ryo Ueno; Alessandro Navacchia; Nathan D Schilaty; Gregory D Myer; Timothy E Hewett; Nathaniel A Bates Journal: Orthop J Sports Med Date: 2021-09-29
Authors: Ryo Ueno; Alessandro Navacchia; Nathan D Schilaty; Gregory D Myer; Timothy E Hewett; Nathaniel A Bates Journal: Orthop J Sports Med Date: 2021-03-09