OBJECTIVE: To evaluate the effects of different mold materials, their diameters, and light-curing units on the mechanical properties of three resin-based composites (RBC). METHODS AND MATERIALS: A conventional nano-filled resin composite (Filtek Supreme Ultra, 3M Oral Care, St Paul, MN, USA) and two bulk-fill composites materials, Tetric Evoceram Bulk fill (Ivoclar Vivadent, Schaan, Liechtenstein) and Aura Bulk Fill (SDI, Bayswater, VIC, Australia), were tested. A total of 240 specimens were fabricated using metal or white semitransparent Delrin molds that were 4 or 10 mm in diameter. The RBCs were light cured for 40 seconds on the high-power setting of either a monowave (DeepCure-S, 3M Oral Care) or polywave (Bluephase G2, Ivoclar Vivadent) light-emitting diode (LED) curing unit. The depth of cure was determined using a scraping test, according to the 2009 ISO 4049 test method. Data were analyzed using multivariate analysis of variance followed by Tukey multiple comparison test ( p<0.05). RESULTS: In general, when used for 40 seconds, both LED curing lights achieved the same depth of cure ( p=0.157). However, the mold material and its diameter had a significant effect on the depth of cure of all three RBCs ( p<0.0001). CONCLUSION: Curing with either the polywave or monowave LED curing light resulted in the same depth of cure in the composites. The greatest depth of cure was always achieved using the 10-mm-diameter Delrin mold. Of the three RBCs tested, both Tetric Bulk Fill and Aura achieved a 4-mm depth of cure when tested in the 10-mm-diameter metal mold. Tetric Bulk Fill was the most transparent and had the greatest depth of cure, and the conventional composite had the least depth of cure. Very little violet (<420 nm) light penetrated through 6 mm of any of the RBCs.
OBJECTIVE: To evaluate the effects of different mold materials, their diameters, and light-curing units on the mechanical properties of three resin-based composites (RBC). METHODS AND MATERIALS: A conventional nano-filled resin composite (Filtek Supreme Ultra, 3M Oral Care, St Paul, MN, USA) and two bulk-fill composites materials, Tetric Evoceram Bulk fill (Ivoclar Vivadent, Schaan, Liechtenstein) and Aura Bulk Fill (SDI, Bayswater, VIC, Australia), were tested. A total of 240 specimens were fabricated using metal or white semitransparent Delrin molds that were 4 or 10 mm in diameter. The RBCs were light cured for 40 seconds on the high-power setting of either a monowave (DeepCure-S, 3M Oral Care) or polywave (Bluephase G2, Ivoclar Vivadent) light-emitting diode (LED) curing unit. The depth of cure was determined using a scraping test, according to the 2009 ISO 4049 test method. Data were analyzed using multivariate analysis of variance followed by Tukey multiple comparison test ( p<0.05). RESULTS: In general, when used for 40 seconds, both LED curing lights achieved the same depth of cure ( p=0.157). However, the mold material and its diameter had a significant effect on the depth of cure of all three RBCs ( p<0.0001). CONCLUSION: Curing with either the polywave or monowave LED curing light resulted in the same depth of cure in the composites. The greatest depth of cure was always achieved using the 10-mm-diameter Delrin mold. Of the three RBCs tested, both Tetric Bulk Fill and Aura achieved a 4-mm depth of cure when tested in the 10-mm-diameter metal mold. Tetric Bulk Fill was the most transparent and had the greatest depth of cure, and the conventional composite had the least depth of cure. Very little violet (<420 nm) light penetrated through 6 mm of any of the RBCs.
Authors: Britta Hahn; Imme Haubitz; Ralf Krug; Gabriel Krastl; Sebastian Soliman Journal: Int J Environ Res Public Health Date: 2022-04-19 Impact factor: 4.614
Authors: César F Cayo-Rojas; Karen K Hernández-Caba; Ana S Aliaga-Mariñas; Marysela I Ladera-Castañeda; Luis A Cervantes-Ganoza Journal: BMC Oral Health Date: 2021-12-04 Impact factor: 2.757