Naghmeh Meraji1, Josette Camilleri2. 1. Department of Endodontics, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran. 2. Department of Restorative Dentistry, Faculty of Dental Surgery, University of Malta, Msida, Malta. Electronic address: josette.camilleri@um.edu.mt.
Abstract
INTRODUCTION: Dentin replacement materials are necessary in large cavities to protect the pulp and reduce the bulk of filling material. These materials are layered with a composite resin restorative material. Microleakage caused by poor bonding of composite resin to underlying dentin replacement material will result in pulp damage. The aim of this study was to characterize the interface between dentin replacement materials and composite resin and to measure the shear bond strength after dynamic aging. METHODS: Biodentine (Septodont, Saint Maur-des-Fosses, France), Theracal LC (Bisco, Schaumburg, IL), and Fuji IX (GC, Tokyo, Japan) were used as dentin replacement materials. They were then overlaid with a total-etch and bonding agent or a self-etch primer and composite resin or a glass ionomer cement. All combinations were thermocycled for 3000 cycles. The interface was characterized using scanning electron microscopy and elemental mapping. Furthermore, the shear bond strength was assessed. RESULTS: The Biodentine surface was modified by etching. The Theracal LC and Fuji IX microstructure was unchanged upon the application of acid etch. The Biodentine and glass ionomer interface showed an evident wide open space, and glass particles from the glass ionomer adhered to the Biodentine surface. Elemental migration was shown with aluminum, barium, fluorine, and ytterbium present in Biodentine from the overlying composite resin. Calcium was more stable. The bond strength between Theracal LC and composite using a total-etch technique followed by self-etch primer achieved the best bond strength values. Biodentine exhibited the weakest bond with complete failure of bonding shown after demolding and thermocycling. CONCLUSIONS: Dynamic aging is necessary to have clinically valid data. Bonding composite resin to water-based dentin replacement materials is still challenging, and further alternatives for restoration of teeth using such materials need to be developed.
INTRODUCTION: Dentin replacement materials are necessary in large cavities to protect the pulp and reduce the bulk of filling material. These materials are layered with a composite resin restorative material. Microleakage caused by poor bonding of composite resin to underlying dentin replacement material will result in pulp damage. The aim of this study was to characterize the interface between dentin replacement materials and composite resin and to measure the shear bond strength after dynamic aging. METHODS:Biodentine (Septodont, Saint Maur-des-Fosses, France), Theracal LC (Bisco, Schaumburg, IL), and Fuji IX (GC, Tokyo, Japan) were used as dentin replacement materials. They were then overlaid with a total-etch and bonding agent or a self-etch primer and composite resin or a glass ionomer cement. All combinations were thermocycled for 3000 cycles. The interface was characterized using scanning electron microscopy and elemental mapping. Furthermore, the shear bond strength was assessed. RESULTS: The Biodentine surface was modified by etching. The Theracal LC and Fuji IX microstructure was unchanged upon the application of acid etch. The Biodentine and glass ionomer interface showed an evident wide open space, and glass particles from the glass ionomer adhered to the Biodentine surface. Elemental migration was shown with aluminum, barium, fluorine, and ytterbium present in Biodentine from the overlying composite resin. Calcium was more stable. The bond strength between Theracal LC and composite using a total-etch technique followed by self-etch primer achieved the best bond strength values. Biodentine exhibited the weakest bond with complete failure of bonding shown after demolding and thermocycling. CONCLUSIONS: Dynamic aging is necessary to have clinically valid data. Bonding composite resin to water-based dentin replacement materials is still challenging, and further alternatives for restoration of teeth using such materials need to be developed.
Authors: Paulo J Palma; Joana A Marques; Márcia Antunes; Rui I Falacho; Diana Sequeira; Luís Roseiro; João Miguel Santos; João C Ramos Journal: Clin Oral Investig Date: 2020-10-12 Impact factor: 3.573