Plasmon-enhanced Electrically Light-emitting from ZnO Nanorod Arrays/p-GaN Heterostructure Devices.

Effective and bright light-emitting-diodes (LEDs) have attracted broad interests in fundamental research and industrial application, especially on short wavelength LEDs. In this paper, a well aligned ZnO nanorod arrays grown on the p-GaN substrate to form a heterostructured light-emitting diode and Al nanoparticles (NPs) were decorated to improve the electroluminescence performance. More than 30-folds enhancement of the electroluminescence intensity was obtained compared with the device without Al NPs decoration. The investigation on the stable and transient photoluminescence spectraof the ZnO nanorod arrays before and after Al NPs decoration demonstrated that the metal surface plasmon resonance coupling with excitons of ZnO leads to the enhancement of the internal quantum efficiency (IQE). Our results provide aneffective approach to design novel optoelectronic devices such as light-emitting diodes and plasmonic nanolasers.

Zinc oxide (<span class="Chemical">ZnO), as a competent material with anintrinsic direct wide energy bandgap and largeexciton binding energy, has attracted considerable interest for short-wavelength photonic application in display, illumination, optical communication and information storage and biomedical detection12345678. Many reports have demonstrated its efficient ultravioletexcitonic emission in powders, thin films, light-emittingdiode (LED) and laser diodes under the different optical and electrical excitation91011121314. However, the stable and reproducible p-type ZnO is still in challenge. Alternatively, an n-ZnO/p-GaN heterojunction has been suggested as an important candidate approach for device fabrication and application1516, since GaN has similar fundamental bandgap energy of 3.4 eV, the same wurtzite crystal structure, and a low lattice constant mismatch of 1.9%. Especially, single crystalline one-dimensional ZnO nanostructures grown on GaN filmcan construct nano-sized heterojunctions with high carrier injection rate and nice electroluminescence performance due tothe high crystal quality and high surface-to-volume ratios17. Even so, some physical effect or technological approach are still required to further improve the IQE and the light extraction outward, which is very important to develop novel nanodevices and understand the indwelling scientificfoundation.

Recently, surface plasmon (SP), as collective charge oscillationat <span class="Chemical">metal/dielectric interface, has been actively employed to improve the luminous efficiency of light-emitting materials and devices1819202122. For example, in 2004, Okamoto et al.23 reporteda 14-fold PL enhancement of SP-coupled InGaN/GaN quantum well (QW) by usingsilver (Ag) layers toimprove theinternal quantum efficiencies. In 2008, Cheng et al.24 achieved 3-fold enhancement of the near band emission (NBE) of ZnO films through coupling with localized surface plasmons (LSPs) of the sputtered Ag islands. In addition, the metal Au is also used to enhance the PL of ZnO. In 2010, Cheng et al.25 observed 6-fold PL enhancement of NBE from ZnO nanorods by Au NPs decoration, while the defect-related emission was completelysuppressed. Next year, Niu et al.26 obtained 11-fold PL enhancement of NBE of Au/ZnO nanobelts compared with that of the bare one. In the case of electroluminescence, Kwon et al.27 inserted Ag NPsamong the multiple quantum well (MQW) interlayers to improve the emission efficiency of the blue LED through QW-SP coupling. Based on ZnO materials, Zhang et al.28 reported 2.5-fold enhancement of EL from ZnO-based heterojunction LEDs decorated with Ag NPs, and the improvement was attributed to the resonant coupling between excitons of ZnO and localized SPs in Ag NPs. Next year, they obtained 3.7-fold enhancement of EL by optimizing Ag localized SPs29. The same year, Liu et al.30 achieved 7-fold EL enhancement from Ag NPs decorated ZnO-based heterojunction LEDs via optimizing the thickness of MgO spacer layer. Recently, 13-folds enhancement of the UV LEDs has been obtained by the same group31 through embedding a ZnO nanorod array/p-GaN film heterostructure into an Ag-nanoparticles/PMMAcomposite. Further, a recent study by Qiao et al. demonstrates that the lasing threshold of aZnO laser diode can be effectively reduced by introducing Ag NP LSPs32. Many researches demonstratedthat the SP coupling at metal/semiconductor interface could increase the density of states, accelerate the recombination rate, and then enhance the internal quantum efficiency. However, thoseplasmon response spectra in the visible range presentthe big frequency mismatchfrom the NBE of ZnO, and hence suppress the effectively coupling between the metal SPs and the ZnO excitons. On the other hand, noble metals are always costly, which definitelyrestricts the potential for commercialization.

In view of the low cost and its abundance in the world, aluminium (Al) element has now been an important candidate of plasmonic material due to its negative real part and relatively low imaginary part of the dielectric function even at wavelength smaller than 200 nm33. ThereforeAl is a betterplasmonic material than either Au or Ag in the blueand UV range. More importantly, more than 170-fold PL enhancement of <span class="Chemical">ZnO/Al hybrid microcavity induced by the resonant coupling between excitons of ZnO and SPs of Al nanoparticles (Al NPs) had been proved in our previous work34. In this paper, Al NP-decorated n-ZnO nanorods/p-GaN light-emitting array has been designed andconstructed, and great EL enhancement more than 30-fold was obtained compared with that of the bare one. The SP-coupling mechanism wasinvestigated systematically based on the stable and transient photoluminescence (PL) spectraof the bare and Al-decorated LEDs.

Results and Discussion

Figure 1a,b are the top view and side view SEM images of the as-grown ZnO nanorod arrays. The diameter of the <span class="Chemical">ZnO nanorods is ~300 nm from the enlarged top view SEM image inserted in Fig. 1a. The length of the ZnO nanorods is ~8 μm. For the fabrication of EL device, vertically well-aligned n-type ZnO nanorod arrays were grown on p-GaN (0001) substrate with the similar length by a simple vapor-phase transport process. Typical XRD pattern for the ZnO nanorods are shown in Fig. 1d. The high intensity of diffraction peaks reveals the growth direction along the [0001] direction in Fig. 1d. The two diffraction peaks at 34.46° and 72.59° are peculiar to (0002) and (0004) planes of the wurtzite ZnO. The strongest diffraction peak corresponds to the (0002) diffraction plane means that the nanorods mainly grow along the preferred [0001] direction, which was further verified by HRTEM shown in Fig. 1f. On the enlarged views of Fig. 1d’s inset, one can observe the ZnO (0002) diffraction peak on the left side of the GaN (0002) reflection. The patterns are typical of a perfectly textured ZnO material. The full width at half-maximum (FWHM) of the (0002) peak for ZnO and GaN are low and similar at 0.085° and 0.095°, respectively. The values are typical of a high-quality heterojunction. The elemental mapping profiles of the Al-decorated ZnO nanorod arrays confirm the existence of Al element, as shown in Fig. 1c. The elemental mapping images collected from the rectangle region in Fig. 1c reveals that the Zn element and O element distribute uniformly corresponding distinctly to the profile of the ZnO nanorod, while the Al element disperses on the surface of ZnO nanorod. Figure 1e,f show TEM and HRTEM images of ZnO nanorod decorated with Al NPs. It further confirms that the diameter of Al NPs is in the range of 15–20 nm. The HRTEM image reveals that the interplanar distance of 0.23 nm corresponds to the d spacing of (111) lattice plane of Al zinc blende structure.

Figure 1

(a) Top and (b) side view SEM images of the as-grown ZnO nanorods. (c) Zn, O, Al element mapping images for the ZnO nanorod. (d) X-ray diffraction patterns of the ZnO nanorod arrays inserted with an enlarged view of the ZnO (002)/GaN (002) region. (e) TEM and (f) HRTEM images of ZnO nanorod decorated with Al nanoparticles.

To examine optical properties of the as-grown ZnO nanorod arrays before and after decoration of Al NPs, the PL spectra of these two samples and the absorption spectra of quartz substrate with and without Al NPs measurements have been performed at room temperature, as shown in Fig. 2a,b. Before Al NPs decoration, a weak ultraviolet emission assigned to the NBE of <span class="Chemical">ZnO and a strong green emission related with the defect in ZnO can be observed. After decoration with Al NPs, the intensity of the ultraviolet emission increased obviously, while the defect-related emission was suppressed. More than 40-fold enhancement was obtained compared with that of the bare one, which was attributed to the direct resonant coupling between the excitons of ZnO and surface plasmons (SPs) of Al NPs as mentioned before. The absorption spectra also verify that PLenhancementresults from the energy couplingbetween SPs and excitons. To gain more insights of the coupling mechanism, time-resolved photoluminescence (TRPL) measurements were performed at room temperature shown in Fig. 2a. The spontaneous emission decay rate of ZnO nanorods is significantly enhanced in the plasmon-coupled device due to Purcell effect. Panels d and e in Fig. 2 show the temporal spectroscopic profile of the bare and the Al-decorated ZnO nanorods. All the normalized TRPL decays can be fitted using a monoexponential function well. The instrument temporal response has been deconvolved from the fits. The fitted decay times are ~202.5 ps for the Al-decorated sample, whereas ~1281.6 ps for the bare ZnO nanorods. The Purcell enhancement factor Fp quantifies the increase in spontaneous emission rate into a mode of interest, and can be derived from the measured TR-PL decay time as follows25:

Figure 2

(a) PL spectraof the ZnO nanorodsbefore and after Al NPs decoration. (b) Transmittance spectra of quartz substrate without and with Al NPs under the same sputtering conditions as the Al-decorated sample.(c) The normalized TRPL spectra and exponential decay fitting curve at the wavelength of 390 nm. Temporal spectroscopic profile of (d) the bare and (e) Al-decorated ZnO nanorods excited by 295 nm laser and collected by a streak camera.

where KPL and are the original and enhanced PL decay rate, respectively. krad, knon and ksp are the radiative, non-radiative and SP-coupling recombination rate of electron-hole pairs, respectively. Using τPL = 1281.6 ps and  = 202.5 ps, an approximate 6.3 time enhancement of the spontaneous emission rate is calculated for the Al-decorated sample. Based on the above results, the efficient resonant coupling has occurred between the <span class="Chemical">SPs of Al nanoparticles and excitons of ZnO nanorods.

The ZnO nanorod array/p-<span class="Gene">GaN heterostructure was used to construct a light-emitting diode device as illustrated in the schematic of Fig. 3a. The top of the ZnO nanorods was contacted directly with an indium tin oxide (ITO) layer deposited on a transparent glass sheet. The GaN layer was contacted with an indium (In) electrode. Figure 3b shows the current versus voltage (I-V) characteristics for the same device before and after Al NPs decoration, which illustrates that the heterojunction behaves like an efficient diode with a current increasing rapidly under forward bias and blocking the current flow under reverse bias. The forward bias turn-on voltages of this device with and without Al nanoparticle decoration were 3.00 V and 3.10 V, respectively. These results indicate that decorating Al nanoparticles on the surface of ZnO nanorods has not caused the electrical properties to deteriorate.

Figure 3

(a) The schematic diagram and (b) I-V characteristic of the device.

Figure 4 shows the room temperature electroluminescence (EL) emission spectra of the bare and Al-decorated devices at different forward biases, inset with an image of the EL spots at the voltage of 30 V. For the bare device, EL spectra show a typical emission peak centered at 393 nm and extend unsymmetrically to 450 nm. However, the EL spectra of the Al-decorated device exhibit a slightly blue shift to 386 nm compared with that of the bare one. Meanwhile, more than 30-folds enhancement of the EL intensity from the Al-decorated device has been observed under the same forward bias. This indicates more efficient recombination of the excited carriers in the Al-decorated device under the electrically driven condition. Corresponding to the enhancement of the PL spectra, the efficient resonant coupling occurred between excitons of ZnO and SPs of Al NPs under electrically driven. The spontaneous recombination rate are increased shown in the transient PL spectra, so are the internal quantum efficiency (ηint), which is given by the ratio of krad and knon23,

Figure 4

The EL spectra of the as-fabricated LED (a) without (b) with Al NPs decoration under different forward biases. The insets show two photographs of the EL emission from the ZnO nanorods/GaN heterojunction diodes (a) before and (b) after decorating with Al NPs.

While the enhanced efficiencies can be related to the coupling rate ksp by the relationship,

where is the probability of photon extraction from the SP’s energy, and is decided by the ratio of the light scattering and dumping of electron vibration. It can be seen that the ηint* increased obviously due to the introduction of the <span class="Chemical">SPs coupling rate, and also suppress the nonradiative transition. Combining equations (1, 2, 3, 4, 5), the IQE ratio between two samples can be obtained as follows:

In order to further catch at the recombination mechanism, a multipeak Guassian fit gives three Guassian bands, centering at ~385 nm, ~400 nm, and ~425 nm for the both bare and Al-decorated devices, respectively. As shown in Fig. 5(a,b), the Guassian curve fits well with the experimental curve. Compared with the PL spectra of the two devices, the UV and blue emission bands centered at 385 nm and 425 nm, respectively, is attributed to the NBE recombinationin <span class="Chemical">ZnO and the electron transition from the conductionband to the deep Mg acceptor level in the Mg-doped p-GaN film, while the emission band centeredat 400 nm results from the interface recombination of the electrons in n-ZnO andholes in p-GaN due to the formation of the energybarrier at the ZnO/GaN heterostructural interface, then the barrier heights at the interface for theholes and the electrons are 0.26 eV and 0.28 eV, respectively. The band diagram of the proposed mechanism for therecombination processes considering the interfacialbarriers and the band diagram was obtained, as shown in Fig. 5c. In addition, the ratio of the emission centered at 400 nm induced by interface recombination to the ultraviolet emission from ZnO nanorods increased with the decoration of Al nanoparticles, which revealed that the efficient coupling occurs between the excitons of ZnO and the SPs of Al. Figure 2b shows that the absorption of Al NPs mainly exists in UV region, which is more benefit for the recombination of ZnO excitons. In the view of the Gaussian fitting curve in Fig. 5b, the enhanced ZnO UV emission and slightly blue shift were due to the higher SP coupling in the shorter wavelength. The SP enhancement of n-ZnO/p-GaN EL provides a promising method for developing highly efficient solid-state light sources.

Figure 5

Gaussian deconvoluted three distinct sub-bands of a representative EL spectrum of ZnO nanorods/GaN heterojunction LED.

(a) before and (b) after Al NPs decoration. (c)The energy band structure of the as-fabricated LED and the corresponding recombination.

In conclusion, we present SP-enhanced <span class="Chemical">ZnO nanorod arrays/p-GaN heterostructurallight-emitting diodes containing decoratedwith Al nanoparticles. In comparison with the bare UV LEDs, the enhancement of luminescence intensity with dozens of times can be observed in both PL and EL spectra from the Al-decorated one. TRPL results showedthat the PL decay time of LEDs decorated with Al nanoparticleswas significantly decreased compared to that of the bare LEDs. And the Purcell enhancement factor F reaches up to 6.3, which indicated that the spontaneousemission rate was increased by the energyresonant coupling betweenthe excitons of ZnO and the SPs of Alnanoparticles. These findings demonstrate that SP coupling is oneof the most interesting methods for developing efficient LEDs, as themetal can be used not only as an electrical contact but also for excitingplasmons.

Methods

Synthesis of ZnO nanorod arrays

ZnO nanorods were fabricated bya vapor phase tranal">sport method. Firstly, a mixture of high purity <span class="Chemical">ZnOand graphite powders (1:1 in mass ratio) was placed in a quartz boat asthe source material. Then, the quartz boat was put in the sealed end of aquartz test tube 30 mm in diameter and 300 mm in length, while a cleaned Mg-doped GaN substrate was put in the open end of the tube. Finally, the whole test tube was transferred into a tube furnace, which had been previously heated to 1050 °C. Argon and oxygen (150:15 sccm) were introduced intothe furnace as the carrier gases. The reaction lasted 15 min. The Al nanoparticles were sputtered onto the ZnO nanorods by a radio frequency magnetic sputtering system. The chamber pressure was fixed at 2.0 Pa, the Ar flow was 50 sccm and the sputtering power was 100 W. The sputtering time lasted 3 min.

LED Fabrication

The Mg-doped GaN with carrier concentration of 3.0 × 1017 cm−3 was used as p-type substrate for LED construction. As shown in the schematic diagram of the LED in Fig. 5(a), the <span class="Chemical">ZnO nanorodswere grown on the p-GaN substrate,and a piece of ITO-coated glass was impacted on them. Theindium electrode was deposited on GaN using the electron beamevaporation system.

Materials and devices characterization

The morphology and structure of the as-synthesized products were characterized by field emission scanning electron microscopy (FESEM, Carl Zeiss Ultra Plus) equipped with an X-ray energy dispersive spectrometer (EDS) (Oxford X-Max 50), X-ray diffraction (XRD-7000, Shimadzu) using Cu Kα radiation (λ = 0.15406 nm) and high-resolution transmissionelectron microscope (HRTEM, JEM-2100). The PLspectrum was measured by a fluorescence spectrophotometer (F-4600, Hitachi) with a Xe lamp at 325 nm as the excitation source. Time-resolved photoluminescence (TRPL) experiments were performed by an optically triggered streak camera system(C10910, Hamamatsu) at 295 nm from frequency doubling of the fundamental 35 fs pulses at 590 nm with a repetition rate of 1 KHz (OperA Solo, Coherent). The I-V characteristics and electrical properties were measured by Keithley 4200.

Additional Information

How to cite this article: Lu, J. et al. Plasmon-enhanced Electrically Light-emitting from ZnO Nanorod Arrays/p-<span class="Gene">GaN Heterostructure Devices. Sci. Rep. 6, 25645; doi: 10.1038/srep25645 (2016).