Literature DB >> 26300326

Elastic Anisotropy of Trabecular Bone in the Elderly Human Vertebra.

Ginu U Unnikrishnan, John A Gallagher, Amira I Hussein, Glenn D Barest, Elise F Morgan.   

Abstract

Knowledge of the nature of the elastic symmetry of trabecular bone is fundamental to the study of bone adaptation and failure. Previous studies have classified human vertebral trabecular bone as orthotropic or transversely isotropic but have typically obtained samples from only selected regions of the centrum. In this study, the elastic symmetry of human vertebral trabecular bone was characterized using microfinite element (μFE) analyses performed on 1019 cubic regions of side length equal to 5 mm, obtained via thorough sampling of the centrums of 18 human L1 vertebrae (age = 81.17 ± 7.7 yr; eight males and ten females). An optimization procedure was used to find the closest orthotropic representation of the resulting stiffness tensor for each cube. The orthotropic elastic constants and orientation of the principal elastic axes were then recorded for each cube and were compared to the constants predicted from Cowin's fabric-based constitutive model (Cowin, 1985, "The Relationship Between the Elasticity Tensor and the Fabric Tensor," Mech. Mater., 4(2), pp. 137-147.) and the orientation of the principal axes of the fabric tensor, respectively. Deviations from orthotropy were quantified by the "orthotropic error" (van Rietbergen et al., 1996, "Direct Mechanics Assessment of Elastic Symmetries and Properties of Trabecular Bone Architecture," J. Biomech., 29(12), pp. 1653-1657), and deviations from transverse isotropy were determined by statistical comparison of the secondary and tertiary elastic moduli. The orthotropic error was greater than 50% for nearly half of the cubes, and the secondary and tertiary moduli differed from one another (p < 0.0001). Both the orthotropic error and the difference between secondary and tertiary moduli decreased with increasing bone volume fraction (BV/TV; p ≤ 0.007). Considering only the cubes with an orthotropic error less than 50%, only moderate correlations were observed between the fabric-based and the μFE-computed elastic moduli (R2 ≥ 0.337; p < 0.0001). These results indicate that when using a criterion of 5 mm for a representative volume element (RVE), transverse isotropy or orthotropy cannot be assumed for elderly human vertebral trabecular bone. Particularly at low values of BV/TV, this criterion does not ensure applicability of theories of continuous media. In light of the very sparse and inhomogeneous microstructure found in the specimens analyzed in this study, further work is needed to establish guidelines for selecting a RVE within the aged vertebral centrum.

Entities:  

Mesh:

Year:  2015        PMID: 26300326      PMCID: PMC4844108          DOI: 10.1115/1.4031415

Source DB:  PubMed          Journal:  J Biomech Eng        ISSN: 0148-0731            Impact factor:   2.097


  18 in total

1.  Constitutive relationships of fabric, density, and elastic properties in cancellous bone architecture.

Authors:  J Kabel; B van Rietbergen; A Odgaard; R Huiskes
Journal:  Bone       Date:  1999-10       Impact factor: 4.398

2.  Dependence of yield strain of human trabecular bone on anatomic site.

Authors:  E F Morgan; T M Keaveny
Journal:  J Biomech       Date:  2001-05       Impact factor: 2.712

3.  Comparison of mixed and kinematic uniform boundary conditions in homogenized elasticity of femoral trabecular bone using microfinite element analyses.

Authors:  Jarunan Panyasantisuk; Dieter H Pahr; Thomas Gross; Philippe K Zysset
Journal:  J Biomech Eng       Date:  2015-01       Impact factor: 2.097

4.  Heterogeneity of bone lamellar-level elastic moduli.

Authors:  C E Hoffler; K E Moore; K Kozloff; P K Zysset; M B Brown; S A Goldstein
Journal:  Bone       Date:  2000-06       Impact factor: 4.398

5.  The effect of regional variations of the trabecular bone properties on the compressive strength of human vertebral bodies.

Authors:  Do-Gyoon Kim; Christine A Hunt; Roger Zauel; David P Fyhrie; Yener N Yeni
Journal:  Ann Biomed Eng       Date:  2007-08-10       Impact factor: 3.934

6.  Effect of specimen-specific anisotropic material properties in quantitative computed tomography-based finite element analysis of the vertebra.

Authors:  Ginu U Unnikrishnan; Glenn D Barest; David B Berry; Amira I Hussein; Elise F Morgan
Journal:  J Biomech Eng       Date:  2013-10-01       Impact factor: 2.097

7.  Comparison of quantitative computed tomography-based measures in predicting vertebral compressive strength.

Authors:  Jenni M Buckley; Kenneth Loo; Julie Motherway
Journal:  Bone       Date:  2006-12-15       Impact factor: 4.398

8.  Relationships between bone morphology and bone elastic properties can be accurately quantified using high-resolution computer reconstructions.

Authors:  B Van Rietbergen; A Odgaard; J Kabel; R Huiskes
Journal:  J Orthop Res       Date:  1998-01       Impact factor: 3.494

9.  Morphology-elasticity relationships using decreasing fabric information of human trabecular bone from three major anatomical locations.

Authors:  Thomas Gross; Dieter H Pahr; Philippe K Zysset
Journal:  Biomech Model Mechanobiol       Date:  2012-10-02

10.  A patient-specific finite element methodology to predict damage accumulation in vertebral bodies under axial compression, sagittal flexion and combined loads.

Authors:  Yan Chevalier; Mathieu Charlebois; Dieter Pahr; Peter Varga; Paul Heini; Erich Schneider; Philippe Zysset
Journal:  Comput Methods Biomech Biomed Engin       Date:  2008-10       Impact factor: 1.763

View more
  1 in total

Review 1.  Bone Mechanical Properties in Healthy and Diseased States.

Authors:  Elise F Morgan; Ginu U Unnikrisnan; Amira I Hussein
Journal:  Annu Rev Biomed Eng       Date:  2018-06-04       Impact factor: 9.590

  1 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.