Ordered and ultrathin reduced graphene oxide LB films as hole injection layers for organic light-emitting diode.

In this paper, we demonstrated the utilization of reduced graphene oxide (RGO) Langmuir-Blodgett (LB) films as high performance hole injection layer in organic light-emitting diode (OLED). By using LB technique, the well-ordered and thickness-controlled RGO sheets are incorporated between the organic active layer and the transparent conducting indium tin oxide (ITO), leading to an increase of recombination between electrons and holes. Due to the dramatic increase of hole carrier injection efficiency in RGO LB layer, the device luminance performance is greatly enhanced comparable to devices fabricated with spin-coating RGO and a commercial conducting polymer PEDOT:PSS as the hole transport layer. Furthermore, our results indicate that RGO LB films could be an excellent alternative to commercial PEDOT:PSS as the effective hole transport and electron blocking layer in light-emitting diode devices.

Background

The two-dimensional (2D) single-layer carbon material, graphene, has emerged as a rising star in the field of materials [1]. Owing to its unique electrical, chemical, and mechanical properties [2], graphene has been developed for various applications in optoelectronics [3], sensors [4,5], and electrochemistry [6,7]. Meanwhile, many studies on graphene-based photovoltaic applications have been carried out, in which graphene was used as active layer materials, electron transport bridges, and transparent electrodes [8-10]. However, the general approaches used to prepare graphene, for instance CVD thermal evaporation, result in high cost fabrication process [11,12].

As the surging interest in graphene-based materials, graphene oxide (GO) has regained significant attention as a solution-processable precursor for bulk production of graphene used on transparent conductors and supercapacitors [13]. The reduced graphene oxide (RGO) can be obtained by reducing GO through chemical and thermal treatment [14]. It has been also demonstrated that RGO exhibits high mechanical strength, as well as combined with interesting physical properties, including high performance of electrical, thermal conductivity, and electrochemical activity [15-17].

Due to the high transparent and electrical performance, RGO has been utilized as an electrode layer for optoelectronic devices such as organic light-emitting diode (OLED) and organic photovoltaic devices [18,19]. RGO film deposition methods, such as spin-coating, spray coating etc., have been demonstrated as effective methods to deposit RGO on indium tin oxide (ITO) electrode as a hole injection layer [20,21]. However, it is still a challenge to address ordered and thickness-controlled arrangement of RGO on ITO as high performance hole injection layers. The arrangement feature of carbon sheets results in the remarkable change of electrical ability that influences the performance of OLED devices dramatically. So, it is worthwhile to obtain well-arranged RGO sheets on ITO as hole injection layer, which provide a superior hole injection performance to prepare OLED devices with high luminescent efficiency.

It is well known that GO can float on a water surface without the need for surfactants or stabilizing agents and some reports about the Langmuir-Blodgett (LB) deposition of GO films have been reported [22,23], but few works focused on the optoelectronic electrode applications of these GO-based LB films. In our previous work, a RGO/conducting polymer composite was prepared as high performance electrochemical capacitor electrode [24]. In this paper, we demonstrate the preparation of a well-ordered and thickness-controlled RGO layer on ITO surface as hole injection layer by using the LB method. This RGO hole injection layer offers tunable arrangement and loading of RGO on a substrate. Limited work is focused on fabricating RGO LB layers as hole injection layer and the performance of related device. Owing to the flexible nature of RGO, the LB deposition technique can substantially suppress the folding and wrinkling of graphene oxide sheets, and the sheets are able to be transferred onto a substrate with defined structure, which could provide preferred film structure for effective hole carrier injection.

Methods

Materials

Graphite flakes used for GO preparation were purchased from Sigma-Aldrich (St. Louis, MO, USA). GO was synthesized from natural graphite flakes through Hummer's method [25]. The size of graphite flakes was 380 μm (grade 3061). In order to obtain stable GO dispersion for LB deposition, 20 mg GO was dissolved in 80 ml methanol/deionized (DI) water (volume ratio 4:1) mixture solution, and the solution was subjected to ultrasonication for 30 min followed by centrifugation at 2,500 rpm. N,N′-Bis(3-methylphenyl)-N,N′-diphenylbenzidine (TPD) and Tris(8-hydroxyquinolinato)aluminium Alq3 were also purchased from Sigma-Aldrich. A commercial conducting polymer PEDOT:PSS (product code as Clevios™ P Jet) was purchased from Bayer company (Leverkusen, Germany). Aluminum as a cathode was purchased from Dongyang Inc. (Shenzhen, China). All solvents used in experiment are high purity level.

Film and device fabrication

The preparation of different-layer GO sheets was carried out in a KSV-5000 LB system (KSV Instruments Ltd., Helsinki, Finland). The self-assembly performance of GO at air-water interface was characterized by a BAM-300 Brewster angle microscopy (KSV Instruments Ltd., Helsinki, Finland). Before the film preparation, the trough was carefully cleaned with chloroform and then filled with DI water. GO solution was dropwise spread onto the water surface by using a glass syringe. Surface pressure was monitored through a tensiometer attached to a Wilhelmy plate. The film was compressed by the barriers at a speed of 1 mm/min. The GO monolayers were transferred to substrates at various points during the compression by vertically dipping the substrate into the trough and slowly pulling it up (1 mm/min). The substrate was first processed with a hydrophilic treatment in order to deposit uniform GO LB layers. By repeating this vertical dipping process, different-layer GO sheets were deposited on substrate uniformly with a layer-by-layer structure. After the deposition of GO LB films, the substrate was treated in a water vapor oven at 200 Co for 6-h GO reduction. Surface morphology of GO and RGO films were investigated by SP 3800 atomic force microscopy (AFM; Seiko Instrument Industry Corporation, Tokyo, Japan) with a tapping mode. The morphological properties of GO and RGO were also investigated with Hitachi S-2400 scanning electron microscopy (SEM; Hitachi, Ltd., Chiyoda, Tokyo, Japan). UV-vis spectrum of the film was recorded on a UV 1700 spectrometer (Shimadzu Corporation, Nakagyo-ku, Kyoto, Japan).

After the preparation of RGO on substrate, the following active layers for OLED were prepared through spin-coating method. The TPD and Alq3 solutions were spin-coated on RGO-covered substrate at 2,000 rpm. The devices used a 50-nm TPD as the hole transport layer and 50-nm Alq3 as the electron transport layer. After the deposition of active layer, an Al cathode electrode was deposited onto the active layer by thermal evaporation in vacuum with a thickness of 60 nm. The OLED with a structure of ITO/RGO LB films/TPD/Alq3/Al-electrode was fabricated, and the device performance was measured at room temperature. For electrical performance testing of GO and RGO films, A Si/SiO2 substrate with prepatterned electrodes was used for current-voltage (I-V) measurement. The interdigitated electrodes had a 15 and 30 μm channel length. The I-V curves were characterized by a Keithley 4200 semiconducting testing system (Cleveland, OH, USA).

Results and discussion

GO can float on a water surface without surfactants or stabilizing due to the geometric similarity of GO with air-water interface, which makes it ideal for accommodating the flat sheets. It can be seen from Figure 1 that GO sheets arrange compactly at the air-water interface with continuous compression. This compact arrangement of GO sheets can be constructed on different substrates through vertical or horizontal deposition. By controlling the surface pressure, the uniform and compact arrangement of graphene oxide sheets can be obtained. Moreover, large area LB deposition can also be realized on GO sheets with tunable arrangement on different substrates.Due to the low conductivity, pure GO is not suitable as a carrier transportation layer and a further-reduced treatment on GO leads to formation of RGO with better conductive performance. Figure 2 shows SEM images of two-layer GO sheets deposited on Si substrate after the thermal treatment. The results reveal that the thermal treatment does not lead to distinct morphology change, and the RGO sheets obtained from GO LB films keep the ordered and compact formation. An investigation of surface roughness characterized by AFM indicates that LB deposition of RGO on ITO gives rise to the surface roughness decrease of ITO. The average thicknesses of the 1-, 2-, and 4-layer RGO LB films were estimated to be 1.2, 2.1, and 3.5 nm, respectively, corresponding to roughness (rms) of 0.50, 0.88, and 1.76 nm. These roughness values are lower than the bare glass/ITO substrate, indicating that the deposition of RGO layers serves to planarize the anode surface. The uniform RGO LB layers display excellent covering performance as the hole injection layer between ITO and active layer. Figure 2c shows the transmission performance of ITO covered by different-layer RGO films. Although the transmittance decreases slightly with thickness, the optical transmission spectra reveal that the GO thin films do not significantly change the transparency of the ITO electrode.

Figure 1

Surface pressure-mean molecular area (π-A) isotherm curves of GO at air-water interface. The inset images show the BAM image of GO evolution at different surface pressures.

Figure 2

SEM images of GO LB films and transmission performance of RGO LB film. (a-b) SEM images of GO LB films with different magnifications after thermal reduction and (c) the transmission performance of RGO LB film-covered ITO.

The thermal treatment results in the change of structure and conductivity performance of GO, leading to the formation of RGO with better conductivity. As shown in Figure 3, the I-V characteristics of GO and RGO LB films display a dramatic enhancement of conductivity after the thermal treatment, indicating the successful thermal reduction of GO to RGO. The thermal treatment makes the reduced GO resemble graphene, whose conductivity is comparable to that of doped conductive polymers, but with some residual oxygen and structural defects [12]. The linear I-V curves of GO and RGO LB films confirm the good ohmic contact between LB film and electrodes. The electrical resistance of GO LB films treated at 200°C is about 5.2 × 103/(Ω m), which is higher than spin-coating PEDOT:PSS films (about 7.3 × 102/(Ω m)) and spin-coating RGO films (about 2.6 × 103/(Ω m)). It has been found that the electrical performance of RGO LB films shows strong dependence on surface pressure of GO film preparation, and the higher surface pressure causes better conductivity of RGO. We conclude that higher surface pressure addresses more compact and continuous arrangement of RGO sheets, resulting in a uniform and compact conducting channel for effective carrier transfer.The electroluminescence (EL) performance of a device with GO, RGO, and commercial PEDOT:PSS as injecting layer are shown in Figure 4. The result indicates that the EL peaks of all devices are located at 578 nm. This result means that the change of injection layer shows no influence on EL peak of an OLED device.Figure 5 shows the I-V curves of devices with different materials as hole injection layer. Compared with spin-coating RGO, GO, and PEDOT:PSS films, the enhanced current density of a device is observed after the insertion of RGO LB films as hole injection layer. The ordered and well-defined structure of hole injection layer plays a important role for effective hole transportation due to the hopping transfer of hole carrier in hole injection layers. Hence, a conducting and well-ordered RGO structure is suitable for this hole injection layers. RGO LB films ensure the enhancement of current and effective hole carrier injection because of highly ordered structure. Moreover, the insertion of ordered and well-defined nanostructure as hole injecting layer further enhances the exciton formation from hole-electron combination. The RGO LB film-based device exhibits larger current at the same applied voltage, indicating a lower driving voltage of device. Compared with RGO LB films, the device with spin-coating RGO layer as hole injection layer shows inferior current performance due to the non-ordered structure of this injection layer. But, compared with GO-based device, better current performance of device based on spin-coating RGO is achieved due to the higher conductivity of RGO.Figure 6 shows the influence of film deposition on I-V performance of devices. It has been found that higher film deposition pressure results in better I-V performance as well as larger current at same voltage. We deduce that RGO LB films obtained from higher surface pressure addresses more compact and continuous arrangement of RGO sheets, resulting in uniform and compact RGO sheets for effective carrier transfer. However, a loose arrangement of RGO sheets makes it difficult for effective hole transferring, and it would also make a negative effect on efficient hole-electron combination and luminance efficiency in OLED.

Figure 3

Current versus voltage (I-V) performance of GO and RGO.

Figure 4

EL spectra of devices with different films as hole injecting layer.

Figure 5

Current-voltage characteristic curves of OLEDs with different films. Current-voltage characteristic curves of OLEDs with different films as hole injection layer. Inset: illustration of device structure based on RGO LB films.

Figure 6

Influence of film deposition pressure on luminance-voltage performance of devices.

Figure 7 shows the luminance-voltage performance of devices with different films as hole injection layers. The best luminance is achieved by device with the RGO LB films as hole injection layer. This device exhibits a maximum luminance of about 6,232 cd/m2 at a 12-V driving voltage, which is higher than the spin-coating RGO and commercial PEDOT:PSS devices. This result indicates that an ultrathin and well-ordered arrangement of nanosheets in hole injection layer obviously enhances hole injection efficiency in OLED, and this well-ordered hole injection layer is also important for OLED to achieve higher luminance performance. We also calculated the band energy of different functional layers in this device. The band energies of the ITO, TPD/Alq3, and Al layers are well known, and a detailed investigation shows that average work function (4.7 eV) of RGO thin films in our work is comparable to ITO for better hole injection.

Figure 7

Luminance-voltage characteristic curves of OLEDs with different hole injection layer. Inset: energy level of different function layers in OLED.

Table 1 shows a detailed performance comparison of devices with different films as hole injection layer. Compared with other devices, the RGO LB film device achieves excellent performance in driving voltage, maximum luminance, and luminance efficiency. We also investigate the influence of heating temperature during reduction of GO on luminance performance of devices, which is shown in Table 2. It can be seen that, with the increase of heating temperature, the efficient reduction of GO is achieved and the RGO-based device exhibits improved luminance performance. In a word, we demonstrate the insertion of well-ordered and highly conductive RGO LB films as hole injection layer for OLED, and these RGO LB films could be an excellent alternative to commercial PEDOT:PSS as the effective hole injection and electron blocking layer for improving luminance efficiency.

Table 1

Performance of devices with different films as hole injecting layer

Device	Driving voltage (V) for 100 mA/cm 2	Max luminance (cd/m 2 , 12 V)	Luminance efficiency (cd/A, 12 V)
PEDOT:PSS spin-coating film	11.7	4,435	2.9
GO spin-coating film	12.1	2,253	1.9
RGO spin-coating film	11.4	4,107	3.0
RGO LB film	9.6	6,232	3.8

Table 2

Influence of heating temperature during thermal reduction on device luminance performance

Heating temperature (°C)	Driving voltage (V) for 100 mA/cm 2	Max luminance (cd/m 2 , 12 V)	Luminance efficiency (cd/A, 12 V)
50	11.3	4,015	2.5
150	10.1	5,527	3.3
200	9.7	6,144	3.7

Conclusions

The LB assembly and a following reduction process produce the high-conductivity and well-ordered-structure RGO LB films. The results of I-V tests indicate that the thermal treatment changes the electrical performance of GO films dramatically. The RGO LB films are successfully incorporated between ITO and active layer as a hole injection layer. The incorporation of well-ordered and thickness-controlled RGO leads to an increase in recombination of electrons and holes as well as the block to the electrons. Our results indicate that RGO LB films are an excellent alternative to commercial PEDOT:PSS as the effective hole transport and electron blocking layer in OLED for improving luminance efficiency.

Competing interests

The authors declare that they have no competing interests.

Authors’ contributions

YY conceived of the study, carried out the fabrication of OLED, and drafted the manuscript. WY and XY helped to deposit LB films and analyze the data. YJ and JX helped to develop the idea and guided the study. SL helped to draft the manuscript. All authors read and approved the final manuscript.

Authors’ information

WY and XY are students of a Master's degree at the School of Optoelectronic Information, University of Electronic Science and Technology of China. YY and SL are associate professors at the School of Optoelectronic Information, University of Electronic Science and Technology of China. JX and YJ are professors at the School of Optoelectronic Information, University of Electronic Science and Technology of China.