Direct deposition of uniform high-κ dielectrics on graphene.

High quality High-κ dielectrics on graphene were achieved by atomic layer deposition directly using remote oxygen plasma surface pretreatment. The uniform coverage on graphene is illustrated by atomic force microscopy and confirmed by high resolution transmission microscopy. The possible surface lattice damage induced by plasma is limited and demonstrated by Raman spectra. The excellent Hall mobility for graphene is maintained at 2.7 × 10(3) cm(2)/V · s, which only decreases by 25%. The excellent electrical characteristic of dielectric presents the low leakage current density and high breakdown voltage. Moreover, the technology is compatible with the traditional CMOS process which brings much possibility to future graphene devices.

The emerging extensive application of graphene attracts intensive attention as a promising material for future nano-electronics with high intrinsic carrier mobility123. The high quality graphene/oxide interface is critical to electronic devices such as radio-frequency transistor45 and flexible electronics67. A lot of efforts have been made to realize atomic layer deposition (ALD) of high-κ dielectrics with high quality on the top of graphene. With the help of a functionalization layer of NO2-trimetdhylaluminum (TMA)8 or using different ultra-thin metal films as a nucleation layer to enable the ALD process910, the Al2O3 has been successfully deposited on graphene indirectly. Recently, high-κ dielectrics have been achieved on graphene through spin-coating a polymer buffer layer in advance, which has less degradation for the carrier mobility1112. Although these methods have provided successful dielectric deposition on graphene, the high quality graphene/oxide interface is still not obtained especially on the optimization electrical characteristics. The introduction of polymer and the indirect fabrication process will not only reduce the thermal budget of the device but also be incompatible with the traditional CMOS process, which limits the application seriously. Additionally, to achieve better graphene/oxide interfaces, understanding the physical nature of the dynamic deposition process is very important. However, clear clarification is still lacking in literature.

In this letter, we have developed a method for the formation of high quality uniform graphene/oxide interface directly by ALD deposition with remote oxygen plasma treatment. We report only 25% degradation in carrier mobility after optimized dielectric deposition with >1.2 MV/cm dielectric breakdown electrical field intensity and <10−7 A/cm2 leakage current density. In this investigation, we propose the physical images of the dielectric deposition process by ALD via remote oxygen plasma and the results of in-situ x-ray photoelectron spectroscopy (XPS) analysis verified the mechanism.

Results

The atomic force microscope (AFM) image of a 5 μm × 5 μm area is shown in Fig. 1(a). Before dielectric is deposited, there are some ripples on graphene surface which is inevitable because of the transferring graphene to a silicon substrate process and surface roughness is about 1.28 nm13. After the remote plasma pretreatment and the following deposition, good conformal coverage of Al2O3 with few pinholes is observed, as shown in Fig. 1(b). The ripples are less obvious and the surface roughness decreases to 0.90 nm which indicates the uniform Al2O3 film coating. As illustrated in HRTEM cross-sectional images of Fig. 2, the Al2O3 is confirmed on the top of graphene surface and an interfacial layer between graphene and dielectric is found. The Al2O3 thickness is about 18.4 nm which is in accordance with the growth rate of the Al2O3 ALD process. An interfacial layer between graphene and oxide is observed and the thickness is about 2 nm.

Figure 1

AFM images of graphene (a) before and (b) after deposited Al2O3 via O2 plasma surface pretreated ALD process.

Figure 2

HRTEM images of the cross-sectional Al/Al2O3/graphene/Si structure.

Representative Raman spectra were measured (with a 514 nm laser) before and after dielectric deposition, as shown in Fig. 3. Common features of graphene, the G and 2D peaks, which lie at around 1580 cm−1 and 2700 cm−1 are observed1415. Before ALD process, the D band (~1345 cm−1) is not found in the spectrum which implies the transferring process doesn't bring in many disorders to graphene on silicon substrate. After the oxygen plasma surface pretreatment and ALD Al2O3, a low disorder-induced D band occurs which indicates defects were introduced during the process16. A shift of 2D peak is observed after Al2O3 deposition, which confirms that the doping effect occurs on graphene. The doping level of graphene can be estimated. The remote O2 plasma pretreatment before ALD can introduce some active oxygen-containing functional groups to graphene surface forming nucleation sites to make the subsequent ALD reaction easier. However, these functional groups will also break the sp2 hybridization and bring in some disorders which may lead to the appearance of D band. As shown in blue in Fig. 3, though the O2 plasma exposure and ALD process induce disorders in graphene, the D/G intensity ratio is less than 0.1 which still indicates limited damage and good quality of graphene surface1718.

Figure 3

Raman spectra of graphene before (red line) and after (blue line) ALD Al2O3 with O2 plasma pretreatment.

The Hall effect measurements were performed with the Van der Pauw method. In order to eliminate the contribution for mobility of the substrate, we use a 1 cm × 1 cm graphene sample on SiO2 substrate and the transferring steps are the same as before. The Hall mobility for graphene transferred on SiO2 substrate is about 3.606 × 103 cm2/(V·s). After oxygen plasma pretreatment and ALD process, the measured Hall mobility reduces to 2.705 × 103 cm2/(V·s). The decrease of Hall mobility is reasonable since the break of sp hybridization during O2 plasma exposure and the interfacial scattering, but compared to the Hall mobility before ALD, the 25% reduction is still acceptable.

In order to further evaluate the dielectric, top Al electrodes were manufactured by means of physical vapor deposition (PVD) for Al2O3/graphene/highly-doped silicon structure. I–V measurements were conducted by biasing top electrodes from 0 to 5 V at a ramp rate of 0.01 V/s. Fig. 4 shows the current density (J) varies with the electric field (E). The sample presents the leakage current is about 10−7 A/cm2 before breakdown which indicates the good insulation effect of Al2O3 dielectric. The leakage current is probably attributed to the trap-assisted tunneling mechanism. Electrons are injected from interfacial traps to the oxygen vacancies near the interface, and the thermionic field emission of electrons between the oxygen vacancies could form a conductive path for electrons to leak19. At a large bias, the current increases quickly by 3 or 4 orders of magnitude and reaches the compliance limit (1 mA). The breakdown occurs at 1.2 MV/cm which is smaller than the Al2O3 breakdown field20. We attribute the phenomenon to the interfacial contact between graphene and Al2O3. Defects formed at interface between the graphene and dielectric could lead to early breakdown of Al2O3. The insert picture (b) of Fig. 4 shows the C-V measurement of the structure. The value of the dielectric constant is 8.73, which further confirms that good gate dielectrics are formed on graphene by direct atomic layer deposition.

Figure 4

The current density versus the electric field (J-E) characteristics of Al/Al2O3/graphene/Si structure.

Insert: (a) a schematic band-diagram of the structure when Al is biased to a positive voltage, (b) the C-V curve of the structure.

Discussion

Fig. 5(a) shows the dynamic mechanism of Al2O3 dielectric forming on the top of graphene by remote oxygen plasma pretreated ALD. The oxygen plasma firstly generates remotely. After the oxygen plasma process, both the C-O bond and C = O bond are formed on the graphene surface and edge which change the graphene surface from hydrophobic to hydrophilic and make the following ALD process easier to happen. In order to prove the mechanism, we performed in-situ XPS analysis of C 1 s of graphene surface before and after oxygen plasma is introduced to surface. The Fig. 5(b) shows a single C-C peak located at 284.8 eV which indicates high quality graphene before plasma pretreatment21. After remote oxygen plasma is flown to surface, as shown in Fig. 5(c), the C-O peak (286.6 eV) and C(O)O peak (289.3 eV) are observed which indicates the transformation of sp hybridization to sp hybridization22. The C-O bond and C(O)O bond induced by oxygen plasma create the precondition for ALD process at the sacrifice of breaking the two-dimensional planar crystal structure and decreasing the mobility. However, by careful controlling of plasma exposure time and adjusting sp/sp ratio, we can realize ALD high quality dielectric on the surface of graphene with introducing only limited damage.

Figure 5

(a) The dynamic mechanism of Al2O3 dielectric forming on top of graphene by remote O2 plasma pretreated ALD. The in-situ XPS of C spectra of (b) before and (c) after oxygen plasma treatment.

In summary, we successfully deposited ~18.4 nm Al2O3 dielectric on graphene after 200 ALD cycles. The uniform coverage with the roughness of 0.9 nm and good graphene/oxide interface are confirmed by AFM and HRTEM. Since the O2 plasma is generated remotely and the time for exposure is well-controlled during the process, the damage introduced to graphene lattice is limited which is revealed by Raman spectra. As a result, only 25% degradation of Hall mobility was detected by this method. Furthermore, we fabricated the top electrodes for Al2O3/graphene/highly-doped silicon structure to evaluate the electrical characteristic. A low leakage current density of 10−7 A/cm2 which indicates good insulation effect of dielectric is observed and the breakdown occurs at 1.2 MV/cm. The in-situ XPS analysis of C spectra reveals O2 plasma pretreatment could break sp hybridization and make the surface hydrophilic for the following ALD process. These results will provide a new solution for future application in graphene based devices that could be compatible with the CMOS fabrication process.

Methods

The graphene was synthesized by the Cu-catalyzed low-pressure chemical vapor deposition. Following this synthesis, graphene was transferred by spin-coating a “handle” layer which comprises of poly (methylmethacrylate (PMMA)). The PMMA layer was used to support the graphene film while the Cu substrate was etched in FeCl3. The obtained PMMA/graphene membrane was then transferred to a highly-doped silicon substrate. After removing PMMA with acetone, cleaning and drying, the graphene/n+-Si sample was transferred to ALD chamber. The whole ALD process with remote O2 plasma surface pretreatment was undertaken in the Picosun R200 system. After remote O2 plasma exposure for 20 seconds (s), Al2O3 was deposited at ~250°C using TMA and water as precursors for 200 cycles. The pulse time for TMA was 0.1 s, which is followed by a 6 s purge, 0.1 s H2O pulse and 10 s purge. The resulting growth rate was about 0.1 nm/cycle and the obtained Al2O3 film thickness was about 20 nm. In order to evaluate the quality of the dielectric in electrical characteristics, we made top electrodes using sputtering and the electrode thickness was about 100 nm. The top electrodes made of Al were formed by hard mask with a radius of 100 μm.