STUDY DESIGN: Twelve Cadisc-L devices were subjected to flexion (0°-6°) and extension (0° to -3°) motions at compressive loads between 500 N and 2000 N at a flexural rate between 0.25°/s and 3.0°/s. OBJECTIVE: To quantify the change in flexural properties of the Cadisc-L (elastomeric device), when subjected to increasing magnitudes of axial load and at different flexural rates. SUMMARY OF BACKGROUND DATA: The design of motion preservation devices, used to replace degenerated intervertebral discs, is commonly based on a low-friction, ball-and-socket-articulating joint. Recently, elastomeric implants have been developed that attempt to provide mechanical and motion properties that resemble those of the natural disc more closely. METHODS: Twelve Cadisc-L devices (MC-10 mm-9° and MC-10 mm-12° size) were supplied by Ranier Technology Ltd (Cambridge, United Kingdom). The devices were hydrated and tested using a Bose spinal disc-testing machine (Bose Corporation, ElectroForce Systems Group, Eden Prairie, MN) in Ringer's solution at 37°C. A static load of 500 N was applied to a device and it was then subjected to motions of 0° to 6° to 0° (flexion) and 0° to -3° to 0° (extension) at a flexural rate of 0.25°/s, 0.5°/s, 1.0°/s, 1.5°/s, 2.0°/s, and 3.0°/s. Tests were repeated at 1000 N, 1500 N, and 2000 N. RESULTS: Regression analyses showed a significant (R > 0.99, P < 0.05) linear increase in bending moment and flexural stiffness with flexion and extension angles (at 1000 N and higher loads)-a significant (R > 0.994, P < 0.05) linear decrease in flexural stiffness in flexion and extension as flexural rate increased. CONCLUSION: The bending moment of the Cadisc-L increased linearly with flexion and extension angles at 1000 N and higher loads. Flexural stiffness increased with compressive load but decreased with flexural rate.
STUDY DESIGN: Twelve Cadisc-L devices were subjected to flexion (0°-6°) and extension (0° to -3°) motions at compressive loads between 500 N and 2000 N at a flexural rate between 0.25°/s and 3.0°/s. OBJECTIVE: To quantify the change in flexural properties of the Cadisc-L (elastomeric device), when subjected to increasing magnitudes of axial load and at different flexural rates. SUMMARY OF BACKGROUND DATA: The design of motion preservation devices, used to replace degenerated intervertebral discs, is commonly based on a low-friction, ball-and-socket-articulating joint. Recently, elastomeric implants have been developed that attempt to provide mechanical and motion properties that resemble those of the natural disc more closely. METHODS: Twelve Cadisc-L devices (MC-10 mm-9° and MC-10 mm-12° size) were supplied by Ranier Technology Ltd (Cambridge, United Kingdom). The devices were hydrated and tested using a Bose spinal disc-testing machine (Bose Corporation, ElectroForce Systems Group, Eden Prairie, MN) in Ringer's solution at 37°C. A static load of 500 N was applied to a device and it was then subjected to motions of 0° to 6° to 0° (flexion) and 0° to -3° to 0° (extension) at a flexural rate of 0.25°/s, 0.5°/s, 1.0°/s, 1.5°/s, 2.0°/s, and 3.0°/s. Tests were repeated at 1000 N, 1500 N, and 2000 N. RESULTS: Regression analyses showed a significant (R > 0.99, P < 0.05) linear increase in bending moment and flexural stiffness with flexion and extension angles (at 1000 N and higher loads)-a significant (R > 0.994, P < 0.05) linear decrease in flexural stiffness in flexion and extension as flexural rate increased. CONCLUSION: The bending moment of the Cadisc-L increased linearly with flexion and extension angles at 1000 N and higher loads. Flexural stiffness increased with compressive load but decreased with flexural rate.