Literature DB >> 21499538

Characterization of dimethacrylate polymeric networks: a study of the crosslinked structure formed by monomers used in dental composites.

Carmem S Pfeifer1, Zachary R Shelton, Roberto R Braga, Dario Windmoller, José C Machado, Jeffrey W Stansbury.   

Abstract

The resin phase of dental composites is mainly composed of combinations of dimethacrylate comonomers, with final polymeric network structure defined by monomer type/reactivity and degree of conversion. This fundamental study evaluates how increasing concentrations of the flexible triethylene glycol dimethacrylate (TEGDMA) influences void formation in bisphenol A diglycidyl dimethacrylate (BisGMA) co-polymerizations and correlates this aspect of network structure with reaction kinetic parameters and macroscopic volumetric shrinkage. Photopolymerization kinetics was followed in real-time by a near-infrared (NIR) spectroscopic technique, viscosity was assessed with a viscometer, volumetric shrinkage was followed with a linometer, free volume formation was determined by positron annihilation lifetime spectroscopy (PALS) and the sol-gel composition was determined by extraction with dichloromethane followed by (1)H-NMR analysis. Results show that, as expected, volumetric shrinkage increases with TEGDMA concentration and monomer conversion. Extraction/(1)H-NMR studies show increasing participation of the more flexible TEGDMA towards the limiting stages of conversion/crosslinking development. As the conversion progresses, either based on longer irradiation times or greater TEGDMA concentrations, the network becomes more dense, which is evidenced by the decrease in free volume and weight loss after extraction in these situations. For the same composition (BisGMA/TEGDMA 60-40 mol%) light-cured for increasing periods of time (from 10 to 600 s), free volume decreased and volumetric shrinkage increased, in a linear relationship with conversion. However, the correlation between free volume and macroscopic volumetric shrinkage was shown to be rather complex for variable compositions exposed for the same time (600 s). The addition of TEGDMA decreases free-volume up to 40 mol% (due to increased conversion), but above that concentration, in spite of the increase in conversion/crosslinking, free volume pore size increases due to the high concentration of the more flexible monomer. In those cases, the increase in volumetric shrinkage was due to higher functional group concentration, in spite of the greater free volume. Therefore, through the application of the PALS model, this study elucidates the network formation in dimethacrylates commonly used in dental materials.

Entities:  

Year:  2011        PMID: 21499538      PMCID: PMC3074112          DOI: 10.1016/j.eurpolymj.2010.11.007

Source DB:  PubMed          Journal:  Eur Polym J        ISSN: 0014-3057            Impact factor:   4.598


  18 in total

1.  Determination of double bond conversion in dental resins by near infrared spectroscopy.

Authors:  J W Stansbury; S H Dickens
Journal:  Dent Mater       Date:  2001-01       Impact factor: 5.304

2.  Contraction stress related to degree of conversion and reaction kinetics.

Authors:  R R Braga; J L Ferracane
Journal:  J Dent Res       Date:  2002-02       Impact factor: 6.116

3.  Influence of pulse-delay curing on softening of polymer structures.

Authors:  E Asmussen; A Peutzfeldt
Journal:  J Dent Res       Date:  2001-06       Impact factor: 6.116

4.  Network structure of Bis-GMA- and UDMA-based resin systems.

Authors:  Cynthia J E Floyd; Sabine H Dickens
Journal:  Dent Mater       Date:  2006-01-10       Impact factor: 5.304

5.  Light initiation of dental resins: dynamics of the polymerization.

Authors:  B A Venhoven; A J de Gee; C L Davidson
Journal:  Biomaterials       Date:  1996-12       Impact factor: 12.479

6.  Study of water sorption, solubility and modulus of elasticity of light-cured dimethacrylate-based dental resins.

Authors:  I Sideridou; V Tserki; G Papanastasiou
Journal:  Biomaterials       Date:  2003-02       Impact factor: 12.479

7.  The effects of light intensity, temperature, and comonomer composition on the polymerization behavior of dimethacrylate dental resins.

Authors:  L G Lovell; S M Newman; C N Bowman
Journal:  J Dent Res       Date:  1999-08       Impact factor: 6.116

8.  Degree of cure and fracture properties of experimental acid-resin modified composites under wet and dry conditions.

Authors:  Francisco López-Suevos; Sabine H Dickens
Journal:  Dent Mater       Date:  2007-11-05       Impact factor: 5.304

9.  Influence of UEDMA BisGMA and TEGDMA on selected mechanical properties of experimental resin composites.

Authors:  E Asmussen; A Peutzfeldt
Journal:  Dent Mater       Date:  1998-01       Impact factor: 5.304

10.  Solvent degradation and reduced fracture toughness in aged composites.

Authors:  J L Ferracane; V A Marker
Journal:  J Dent Res       Date:  1992-01       Impact factor: 6.116

View more
  22 in total

1.  Cytotoxicity of resin composites containing bioactive glass fillers.

Authors:  Satin Salehi; Fernanda Gwinner; John C Mitchell; Carmem Pfeifer; Jack L Ferracane
Journal:  Dent Mater       Date:  2015-01-03       Impact factor: 5.304

2.  Thio-urethane oligomers improve the properties of light-cured resin cements.

Authors:  Ataís Bacchi; Rafael L Consani; Gedalias C Martim; Carmem S Pfeifer
Journal:  Dent Mater       Date:  2015-03-01       Impact factor: 5.304

Review 3.  Dimethacrylate network formation and polymer property evolution as determined by the selection of monomers and curing conditions.

Authors:  Jeffrey W Stansbury
Journal:  Dent Mater       Date:  2012-01       Impact factor: 5.304

4.  Delayed Gelation Through Chain-Transfer Reactions: Mechanism For Stress Reduction In Methacrylate Networks.

Authors:  Carmem S Pfeifer; Nicholas D Wilson; Zachary R Shelton; Jeffrey W Stansbury
Journal:  Polymer (Guildf)       Date:  2011-07-07       Impact factor: 4.430

5.  Effect of the addition of thiourethane oligomers on the sol⿿gel composition of BisGMA/TEGDMA polymer networks.

Authors:  M G Borges; L M Barcelos; M S Menezes; C J Soares; A P P Fugolin; O Navarro; V Huynh; S H Lewis; C S Pfeifer
Journal:  Dent Mater       Date:  2019-08-05       Impact factor: 5.304

6.  Use of (meth)acrylamides as alternative monomers in dental adhesive systems.

Authors:  Ana P Fugolin; Adam Dobson; Wilbes Mbiya; Oscar Navarro; Jack L Ferracane; Carmem S Pfeifer
Journal:  Dent Mater       Date:  2019-02-28       Impact factor: 5.304

7.  Influence of bioactive particles on the chemical-mechanical properties of experimental enamel resin infiltrants.

Authors:  Ravana Angelini Sfalcin; Américo Bortolazzo Correr; Lucas Rafael Morbidelli; Tatiany Gabrielle Freire Araújo; Victor Pinheiro Feitosa; Lourenço Correr-Sobrinho; Timothy Frederick Watson; Salvatore Sauro
Journal:  Clin Oral Investig       Date:  2016-11-12       Impact factor: 3.573

8.  3D printed versus conventionally cured provisional crown and bridge dental materials.

Authors:  Anthony Tahayeri; MaryCatherine Morgan; Ana P Fugolin; Despoina Bompolaki; Avathamsa Athirasala; Carmem S Pfeifer; Jack L Ferracane; Luiz E Bertassoni
Journal:  Dent Mater       Date:  2017-10-27       Impact factor: 5.304

9.  Influence of the base and diluent monomer on network characteristics and mechanical properties of neat resin and composite materials.

Authors:  Nívea Regina de Godoy Fróes-Salgado; Vinícius Gajewski; Bárbara Pick Ornaghi; Carmem Silvia Costa Pfeifer; Marcia Margarete Meier; Tathy Aparecida Xavier; Roberto Ruggiero Braga
Journal:  Odontology       Date:  2014-04-12       Impact factor: 2.634

10.  Methacrylamide-methacrylate hybrid monomers for dental applications.

Authors:  Ana P Fugolin; Steven Lewis; Matthew G Logan; Jack L Ferracane; Carmem S Pfeifer
Journal:  Dent Mater       Date:  2020-06-11       Impact factor: 5.304

View more

北京卡尤迪生物科技股份有限公司 © 2022-2023.