Literature DB >> 19766225

Patient-specific analyses of deep tissue loads post transtibial amputation in residual limbs of multiple prosthetic users.

S Portnoy1, I Siev-Ner, N Shabshin, A Kristal, Z Yizhar, A Gefen.   

Abstract

Active transtibial amputation (TTA) patients are at risk for developing pressure ulcers (PU) and deep tissue injury (DTI) while using their prosthesis. It is therefore important to obtain knowledge of the mechanical state in the internal soft tissues of the residuum, as well as knowledge of the mechanical state upon its surface. Our aim was to apply patient-specific MRI-based non-linear finite element (FE) models to quantify internal strains in TTA prosthetic users (n=5) during load-bearing. By further employing a strain injury threshold for skeletal muscle, we identified patients susceptible to DTI. The geometrical characteristics of the residuum of the TTA participants varied substantially between patients, e.g. the residuum lengths were 7.6, 8.1, 9.2, 11.5 and 13.3cm. We generally found that internal strains were higher in the bone proximity than in the muscle flap periphery. The highest strains, which in some patients exceeded 50% (engineering strain) for compressive, tensile and shear strains, were found in the shortest residual limbs, i.e. the 7.6 and 8.1cm-long limbs. Correspondingly, the lowest strains were found in the 13.3cm-long residuum, which had the bulkiest muscle flap. Yet, even in the case of a long residuum, about a third of the soft tissue volume at the distal tibial proximity area was occupied by large (>5%) internal compressive, tensile and shear strains. For both patients with shorter residual limbs, the internal principal compressive strains above 5% occupied almost the entire distal tibial proximity area. For a patient whose distal tibial end was flat (non-beveled), internal strains were more uniformly distributed, compared to the strain distributions in the other models, where focal elevated strains accumulated in the bone proximity. We found no muscle strains above the immediate injury threshold, indicating that all patients were not at immediate risk for DTI. Two patients whose residuum fat padding was minimal to none, were the only ones identified as theoretically prone to DTI at long (>3h) continuous weight-bearing periods. We conclude that there is a wide variability in internal mechanical conditions between residual limbs across subjects, which necessitates patient-specific quantitative analyses of internal mechanical states in TTA patients, to assess the mechanical performance of the reconstructed limb and in particular, the individual risk for deep PU or DTI.

Entities:  

Mesh:

Year:  2009        PMID: 19766225     DOI: 10.1016/j.jbiomech.2009.08.019

Source DB:  PubMed          Journal:  J Biomech        ISSN: 0021-9290            Impact factor:   2.712


  7 in total

1.  Developing a control framework for self-adjusting prosthetic sockets incorporating tissue injury risk estimation and generalized predictive control.

Authors:  F M Mbithi; A J Chipperfield; J W Steer; A S Dickinson
Journal:  Biomed Eng Lett       Date:  2021-12-02

2.  A simulation-based analysis of the effects of variable prosthesis stiffness on interface dynamics between the prosthetic socket and residual limb.

Authors:  Michael A McGeehan; Peter G Adamczyk; Kieran M Nichols; Michael E Hahn
Journal:  J Rehabil Assist Technol Eng       Date:  2022-07-15

3.  Exploring the role of transtibial prosthetic use in deep tissue injury development: a scoping review.

Authors:  Marisa Graser; Sarah Day; Arjan Buis
Journal:  BMC Biomed Eng       Date:  2020-01-29

Review 4.  Review of the socket design and interface pressure measurement for transtibial prosthesis.

Authors:  Gh Pirouzi; N A Abu Osman; A Eshraghi; S Ali; H Gholizadeh; W A B Wan Abas
Journal:  ScientificWorldJournal       Date:  2014-08-13

5.  Development of an air pneumatic suspension system for transtibial prostheses.

Authors:  Gholamhossein Pirouzi; Noor Azuan Abu Osman; Azim Ataollahi Oshkour; Sadeeq Ali; Hossein Gholizadeh; Wan A B Wan Abas
Journal:  Sensors (Basel)       Date:  2014-09-09       Impact factor: 3.576

6.  Analysis of Pressure Distribution in Transfemoral Prosthetic Socket for Prefabrication Evaluation via the Finite Element Method.

Authors:  Mohd Syahmi Jamaludin; Akihiko Hanafusa; Yamamoto Shinichirou; Yukio Agarie; Hiroshi Otsuka; Kengo Ohnishi
Journal:  Bioengineering (Basel)       Date:  2019-10-24

7.  3D-printable zwitterionic nano-composite hydrogel system for biomedical applications.

Authors:  Nathalie Sällström; Andrew Capel; Mark P Lewis; Daniel S Engstrøm; Simon Martin
Journal:  J Tissue Eng       Date:  2020-10-29       Impact factor: 7.813

  7 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.