PURPOSE: To evaluate the effect of cavity preparation device (i.e. carbide bur, diamond bur, air abrasive, Sonicsys, and Er:YAG laser) on microleakage of Class V resin-based composite (RBC) restorations, the tooth restoration interface and dentin ultrastructure. MATERIALS AND METHODS: Eight groups (n=18) of 9 human molars each were prepared on the buccal and lingual surfaces for Class V RBC restorations using five preparation devices: Group 1: carbide bur #8 round; Group 2: diamond bur #801; Group 3: KCP 1000 air abrasion unit; Group 4: Sonicsys Approx.; Group 5: Er:YAG laser; Group 6: carbide bur plus air abrasive; Group 7: carbide bur plus laser, and Group 8: laser without etching. Circular cavity preparations, 3 mm diameter and 1.5 mm deep, were cut at the CEJ on the buccal and lingual surfaces of each tooth. A bevel was placed on the enamel margin. All cavities were restored using Single Bond adhesive system and Silux Plus according to manufacturer's directions, with the exception that no etchant was used with Group 8. After thermocycling, specimens were tested for microleakage using silver nitrate methodology. Dye penetration data was collected and subjected to non-parametric statistical analysis. SEM analysis of the dentin-RBC interface, as well as the effect of each cavity preparation device on the surface of dentin was performed. RESULTS: Microleakage did not occur in enamel for any method of cavity preparation when the enamel was etched prior to adhesive application. Kruskal-Wallis One-way ANOVA revealed differences in dentin microleakage among the tested groups at alpha=0.05. Mann-Whitney Test for Paired Comparisons at alpha=0.01 demonstrated significantly greater dentin microleakage in Groups 5 and 7 compared to all groups except Group 3 (air abrasive). Although Group 8 had the least microleakage in dentin, this was not significantly different from Groups 1, 2, 4 and 6. SEM observation revealed hybridization at the dentin-resin interface for all groups except for Group 8 (laser prepared, non-etched). Surface analysis showed differences related to the operating mode of each preparation device. CLINICAL SIGNIFICANCE: The method of cavity preparation did not affect microleakage in etched enamel. When using a laser for cavity preparation, enamel should be etched although not etching dentin may help to improve marginal seal.
RCT Entities:
PURPOSE: To evaluate the effect of cavity preparation device (i.e. carbide bur, diamond bur, air abrasive, Sonicsys, and Er:YAG laser) on microleakage of Class V resin-based composite (RBC) restorations, the tooth restoration interface and dentin ultrastructure. MATERIALS AND METHODS: Eight groups (n=18) of 9 human molars each were prepared on the buccal and lingual surfaces for Class V RBC restorations using five preparation devices: Group 1: carbide bur #8 round; Group 2: diamond bur #801; Group 3: KCP 1000 air abrasion unit; Group 4: Sonicsys Approx.; Group 5: Er:YAG laser; Group 6: carbide bur plus air abrasive; Group 7: carbide bur plus laser, and Group 8: laser without etching. Circular cavity preparations, 3 mm diameter and 1.5 mm deep, were cut at the CEJ on the buccal and lingual surfaces of each tooth. A bevel was placed on the enamel margin. All cavities were restored using Single Bond adhesive system and Silux Plus according to manufacturer's directions, with the exception that no etchant was used with Group 8. After thermocycling, specimens were tested for microleakage using silver nitrate methodology. Dye penetration data was collected and subjected to non-parametric statistical analysis. SEM analysis of the dentin-RBC interface, as well as the effect of each cavity preparation device on the surface of dentin was performed. RESULTS: Microleakage did not occur in enamel for any method of cavity preparation when the enamel was etched prior to adhesive application. Kruskal-Wallis One-way ANOVA revealed differences in dentin microleakage among the tested groups at alpha=0.05. Mann-Whitney Test for Paired Comparisons at alpha=0.01 demonstrated significantly greater dentin microleakage in Groups 5 and 7 compared to all groups except Group 3 (air abrasive). Although Group 8 had the least microleakage in dentin, this was not significantly different from Groups 1, 2, 4 and 6. SEM observation revealed hybridization at the dentin-resin interface for all groups except for Group 8 (laser prepared, non-etched). Surface analysis showed differences related to the operating mode of each preparation device. CLINICAL SIGNIFICANCE: The method of cavity preparation did not affect microleakage in etched enamel. When using a laser for cavity preparation, enamel should be etched although not etching dentin may help to improve marginal seal.
Authors: M Tielemans; Ph Compere; S O Geerts; M Lamy; M Limme; R J G De Moor; K I M Delmé; M F Bertrand; E Rompen; S Nammour Journal: Lasers Med Sci Date: 2007-11-24 Impact factor: 3.161
Authors: Marina Stella Bello-Silva; Martin Wehner; Carlos de Paula Eduardo; Friedrich Lampert; Reinhart Poprawe; Martin Hermans; Marcella Esteves-Oliveira Journal: Lasers Med Sci Date: 2012-05-08 Impact factor: 3.161
Authors: Batu Can Yaman; Begüm Güray Efes; Can Dörter; Yavuz Gömeç; Dina Erdilek; Oktay Yazıcıoğlu Journal: Lasers Med Sci Date: 2010-02-17 Impact factor: 3.161
Authors: S Pushpa Latha; Vani Hegde; Syed Ahmed Raheel; Bassel Tarakji; Saleh Nasser Azzeghaiby; Mohammad Zakaria Nassani Journal: J Int Oral Health Date: 2014-09