Michael Wagner1, Tobias Werther2, Ewald Unger3, Gregor Kasprian4, Gregor Dovjak4, Christian Dorfer5, Hannah Schned2, Philipp Steinbauer2, Katharina Goeral2, Monika Olischar2, Karl Roessler5, Angelika Berger2, Gunpreet Oberoi3. 1. Department of Pediatrics and Adolescent Medicine, Division of Neonatology, Intensive Care Medicine and Neuropediatrics, Comprehensive Center for Pediatrics, Medical University of Vienna, Vienna, Austria. michael.b.wagner@meduniwien.ac.at. 2. Department of Pediatrics and Adolescent Medicine, Division of Neonatology, Intensive Care Medicine and Neuropediatrics, Comprehensive Center for Pediatrics, Medical University of Vienna, Vienna, Austria. 3. Center for Medical Physics and Biomedical Engineering, Medical University of Vienna, Vienna, Austria. 4. Department of Biomedical Imaging and Image-guided Therapy, Medical University of Vienna, Vienna, Austria. 5. Department of Neurosurgery, Comprehensive Center for Pediatrics, Medical University of Vienna, Vienna, Austria.
Abstract
BACKGROUND: Medical-imaging-based three-dimensional (3D) printed models enable improvement in skills training, surgical planning, and decision-making. This pilot study aimed to use multimodality imaging and to add and compare 3D ultrasound as a future standard to develop realistic neonatal brain models including the ventricular system. METHODS: Retrospective computed tomography (CT), magnetic resonance imaging (MRI), and 3D ultrasound-based brain imaging protocols of five neonatal patients were analyzed and subsequently segmented with the aim of developing a multimodality imaging-based 3D printed model. The ventricular anatomy was analyzed to compare the MRI and 3D ultrasound modalities. RESULTS: A realistic anatomical model of the neonatal brain, including the ventricular system, was created using MRI and 3D ultrasound data from one patient. T2-weighted isovoxel 3D MRI sequences were found to have better resolution and accuracy than 2D sequences. The surface area, anatomy, and volume of the lateral ventricles derived from both MRI and 3D ultrasound were comparable. CONCLUSIONS: We created an ultrasound- and MRI-based 3D printed patient-specific neonatal brain simulation model that can be used for perioperative management. To introduce 3D ultrasound as a standard for 3D models, additional dimensional correlations between MRI and ultrasound need to be examined. IMPACT: We studied the feasibility of implementing 3D ultrasound as a standard for 3D printed models of the neonatal brain. Different imaging modalities were compared and both 3D isotropic MRI and 3D ultrasound imaging are feasible for printing neonatal brain models with good dimensional accuracy and anatomical replication. Further dimensional correlations need to be defined to implement it as a standard to produce 3D printed models.
BACKGROUND: Medical-imaging-based three-dimensional (3D) printed models enable improvement in skills training, surgical planning, and decision-making. This pilot study aimed to use multimodality imaging and to add and compare 3D ultrasound as a future standard to develop realistic neonatal brain models including the ventricular system. METHODS: Retrospective computed tomography (CT), magnetic resonance imaging (MRI), and 3D ultrasound-based brain imaging protocols of five neonatal patients were analyzed and subsequently segmented with the aim of developing a multimodality imaging-based 3D printed model. The ventricular anatomy was analyzed to compare the MRI and 3D ultrasound modalities. RESULTS: A realistic anatomical model of the neonatal brain, including the ventricular system, was created using MRI and 3D ultrasound data from one patient. T2-weighted isovoxel 3D MRI sequences were found to have better resolution and accuracy than 2D sequences. The surface area, anatomy, and volume of the lateral ventricles derived from both MRI and 3D ultrasound were comparable. CONCLUSIONS: We created an ultrasound- and MRI-based 3D printed patient-specific neonatal brain simulation model that can be used for perioperative management. To introduce 3D ultrasound as a standard for 3D models, additional dimensional correlations between MRI and ultrasound need to be examined. IMPACT: We studied the feasibility of implementing 3D ultrasound as a standard for 3D printed models of the neonatal brain. Different imaging modalities were compared and both 3D isotropic MRI and 3D ultrasound imaging are feasible for printing neonatal brain models with good dimensional accuracy and anatomical replication. Further dimensional correlations need to be defined to implement it as a standard to produce 3D printed models.