Kevin K Ma1, Amy Yuan2, Sina Sharifi3, Roberto Pineda4. 1. From the Department of Ophthalmology, Massachusetts Eye and Ear, Harvard Medical School, Boston, Massachusetts, USA. 2. Department of Ophthalmology, University of Washington, Seattle, Washington, USA. 3. Schepens Eye Research Institute, Harvard Medical School, Boston, Massachusetts, USA. 4. From the Department of Ophthalmology, Massachusetts Eye and Ear, Harvard Medical School, Boston, Massachusetts, USA.. Electronic address: Roberto_Pineda@meei.harvard.edu.
Abstract
PURPOSE: Flanged intrascleral haptic fixation (FISHF) is a useful method for securing intraocular lenses (IOLs) in eyes without capsular support. Biomechanical studies were conducted to support the use of this technique. DESIGN: Laboratory investigation. METHODS: Haptics of 3-piece IOLs were passed through cadaveric human sclera using 30- and 27-gauge needles. Flanges were created by melting 1.0 mm from the haptic ends using cautery. The forces required to remove the flanged haptic from the sclera and disinsert the haptic from the optic were measured using a mechanical tester and a custom-fabricated mount. RESULTS: The mean FISHF dislocation force using 30-gauge needles was greatest with the CT Lucia 602 (2.04 ± 0.24 newtons [N]) compared to the LI61AO (0.93 ± 0.41 N; P = .001), ZA9003 (0.70 ± 0.34 N; P = <.001), and MA60AC (0.27 ± 0.19 N; P <.001). Using 27-gauge needles with the CT Lucia resulted in a lower dislocation force (0.56 ± 0.36 N; P <.001). The FISHF dislocation force was correlated with the flange-to-needle diameter ratio (r = 0.975). The FISHF dislocation forces of the CT Lucia and LI61AO using 30-gauge needles were not significantly different from their haptic-optic disinsertion forces (P = .79 and .27, respectively). There were no differences in flange diameters between 1.0 mm and 2.0 mm haptic melt lengths across the IOLs (P = .15-.85). CONCLUSIONS: These data strongly support the biomechanical stability of FISHF with the polyvinylidene fluoride haptics of the CT Lucia using small diameter instruments for the creation of an intrascleral tunnel. 1.0 mm of haptic may be the optimal melt length.
PURPOSE: Flanged intrascleral haptic fixation (FISHF) is a useful method for securing intraocular lenses (IOLs) in eyes without capsular support. Biomechanical studies were conducted to support the use of this technique. DESIGN: Laboratory investigation. METHODS: Haptics of 3-piece IOLs were passed through cadaveric human sclera using 30- and 27-gauge needles. Flanges were created by melting 1.0 mm from the haptic ends using cautery. The forces required to remove the flanged haptic from the sclera and disinsert the haptic from the optic were measured using a mechanical tester and a custom-fabricated mount. RESULTS: The mean FISHF dislocation force using 30-gauge needles was greatest with the CT Lucia 602 (2.04 ± 0.24 newtons [N]) compared to the LI61AO (0.93 ± 0.41 N; P = .001), ZA9003 (0.70 ± 0.34 N; P = <.001), and MA60AC (0.27 ± 0.19 N; P <.001). Using 27-gauge needles with the CT Lucia resulted in a lower dislocation force (0.56 ± 0.36 N; P <.001). The FISHF dislocation force was correlated with the flange-to-needle diameter ratio (r = 0.975). The FISHF dislocation forces of the CT Lucia and LI61AO using 30-gauge needles were not significantly different from their haptic-optic disinsertion forces (P = .79 and .27, respectively). There were no differences in flange diameters between 1.0 mm and 2.0 mm haptic melt lengths across the IOLs (P = .15-.85). CONCLUSIONS: These data strongly support the biomechanical stability of FISHF with the polyvinylidene fluoride haptics of the CT Lucia using small diameter instruments for the creation of an intrascleral tunnel. 1.0 mm of haptic may be the optimal melt length.
Authors: Sina Sharifi; Hannah Sharifi; Ali Akbari; Darrell Koza; Claes H Dohlman; Eleftherios I Paschalis; James Chodosh Journal: ACS Appl Bio Mater Date: 2021-09-21