Claudinei Dos Santos1, Ingrid Ferreira Coutinho2, José Eduardo Vasconcellos Amarante3, Manuel Fellipe Rodrigues Pais Alves4, Maycol Moreira Coutinho5, Cosme Roberto Moreira da Silva5. 1. UERJ/FAT, Universidade do Estado do Rio de Janeiro, Faculdade de Tecnologia, Rod. Presidente Dutra, km 298, 27.537-000, Resende, RJ, Brazil. Electronic address: claudineisvr@gmail.com. 2. UFF/EEIMVR, Universidade Federal Fluminense, Escola de Engenharia Industrial Metalúrgica de Volta Redonda, Av. dos Trabalhadores, 420, Vila Santa Cecília, 27.255-125, Volta Redonda, RJ, Brazil. 3. UFF/ISNF, Universidade Federal Fluminense, Instituto de Saúde de Nova Friburgo, Faculdade de Odontologia, Estrada Dr. Silvio Henrique Braunet, 22, Centro, 28.625-650, Nova Friburgo, RJ, Brazil. 4. UERJ/FAT, Universidade do Estado do Rio de Janeiro, Faculdade de Tecnologia, Rod. Presidente Dutra, km 298, 27.537-000, Resende, RJ, Brazil. 5. UNB, Universidade de Brasília, Faculdade de Tecnologia, Asa Norte, 70.910-900, Brasilia-DF, Brazil.
Abstract
OBJECTIVES: The objective of this work was the development and characterization of a ceramic composite based on (Ce,Y)-TZP/Al2O3 aiming an application on dental implants, comparing it with conventional monolithic 3Y-TZP ceramics, currently used for the same type of application. METHODS: Ceramic samples, 3Y-TZP (n = 40) and (Ce,Y)-TZP/Al2O3 (n = 40), were sintered at 1500 °C - 2h and characterized by relative density, X-Ray diffraction (XRD) and microstructure. Then, the samples of both materials were divided into two groups: 1) samples with original (as sintered) surfaces; 2) samples with conditioned, polished, surfaces. All samples were submitted to hydrothermal degradation tests, on an autoclave (134 °C - 2 bar), for 10 h in artificial saliva. The degraded samples were characterized by XRD and the polished group were also characterized by their elastic moduli, Vickers hardness and fracture toughness (Vickers indentation method). Both groups were also submitted to a flexural strength test, 3B-P testing, for which the data were interpreted using Weibull statistics. RESULTS: All sintered specimens presented nearly full densification. After the hydrothermal degradation tests, 3Y-TZP samples presented 16.4% of monoclinic (m)-ZrO2 phase while the composite samples withheld 100% of tetragonal (t)-ZrO2 phase. Both materials presented equiaxial ZrO2 grains with an average size of 0.48 ± 0.17 μm and 0.75 ± 0.22 μm, respectively, for the monolithic and composite ceramics. In the composites, is observed the presence of well distributed Al2O3 grains on the ZrO2 matrix, in two distinct morphologies: equiaxial grains and platelets. The composites (Ce,Y)-TZP/Al2O3 presented average values of elastic moduli, Vickers hardness and fracture toughness of 228.3 ± 6.5 GPa, 1427 ± 46 HV e 11.3 ± 0.4 MPa m1/2, respectively. An inversely proportional relationship is observed between the roughness and the bending strength, since the 3Y-TZP samples presented a average strength of 860.7 ± 81 MPa (as-sintered) and 965.4 ± 93 MPa (polished) while the (Ce,Y)-TZP/Al2O3 composites presented average strength of 810.6 ± 147 MPa (as-sintered) and 952.6 ± 88 MPa (polished). CONCLUSIONS: The composites (Ce,Y)-TZP/Al2O3 showed high resistance to degradation in saliva and adequate properties for use as dental implants. Values of flexural strength (>950 MPa) and Weibull modulus (m > 10) were similar to the conventional 3Y-TZP ceramics. Moreover, its hardness, elastic modulus and fracture toughness were higher than those obtained for 3Y-TZP. The expressive values of KIC obtained for (Ce,Y)-TZP/Al2O3 composites are results of association of different toughening mechanisms acting simultaneously in the material.
OBJECTIVES: The objective of this work was the development and characterization of a ceramic composite based on (Ce,Y)-TZP/Al2O3 aiming an application on dental implants, comparing it with conventional monolithic 3Y-TZP ceramics, currently used for the same type of application. METHODS: Ceramic samples, 3Y-TZP (n = 40) and (Ce,Y)-TZP/Al2O3 (n = 40), were sintered at 1500 °C - 2h and characterized by relative density, X-Ray diffraction (XRD) and microstructure. Then, the samples of both materials were divided into two groups: 1) samples with original (as sintered) surfaces; 2) samples with conditioned, polished, surfaces. All samples were submitted to hydrothermal degradation tests, on an autoclave (134 °C - 2 bar), for 10 h in artificial saliva. The degraded samples were characterized by XRD and the polished group were also characterized by their elastic moduli, Vickers hardness and fracture toughness (Vickers indentation method). Both groups were also submitted to a flexural strength test, 3B-P testing, for which the data were interpreted using Weibull statistics. RESULTS: All sintered specimens presented nearly full densification. After the hydrothermal degradation tests, 3Y-TZP samples presented 16.4% of monoclinic (m)-ZrO2 phase while the composite samples withheld 100% of tetragonal (t)-ZrO2 phase. Both materials presented equiaxial ZrO2 grains with an average size of 0.48 ± 0.17 μm and 0.75 ± 0.22 μm, respectively, for the monolithic and composite ceramics. In the composites, is observed the presence of well distributed Al2O3 grains on the ZrO2 matrix, in two distinct morphologies: equiaxial grains and platelets. The composites (Ce,Y)-TZP/Al2O3 presented average values of elastic moduli, Vickers hardness and fracture toughness of 228.3 ± 6.5 GPa, 1427 ± 46 HV e 11.3 ± 0.4 MPa m1/2, respectively. An inversely proportional relationship is observed between the roughness and the bending strength, since the 3Y-TZP samples presented a average strength of 860.7 ± 81 MPa (as-sintered) and 965.4 ± 93 MPa (polished) while the (Ce,Y)-TZP/Al2O3 composites presented average strength of 810.6 ± 147 MPa (as-sintered) and 952.6 ± 88 MPa (polished). CONCLUSIONS: The composites (Ce,Y)-TZP/Al2O3 showed high resistance to degradation in saliva and adequate properties for use as dental implants. Values of flexural strength (>950 MPa) and Weibull modulus (m > 10) were similar to the conventional 3Y-TZP ceramics. Moreover, its hardness, elastic modulus and fracture toughness were higher than those obtained for 3Y-TZP. The expressive values of KIC obtained for (Ce,Y)-TZP/Al2O3 composites are results of association of different toughening mechanisms acting simultaneously in the material.