A Direct Epitaxial Approach To Achieving Ultrasmall and Ultrabright InGaN Micro Light-Emitting Diodes (μLEDs).

A direct epitaxial approach to achieving ultrasmall and ultrabright InGaN micro light-emitting diodes (μLEDs) has been developed, leading to the demonstration of ultrasmall, ultraefficient, and ultracompact green μLEDs with a dimension of 3.6 μm and an interpitch of 2 μm. The approach does not involve any dry-etching processes which are exclusively used by any current μLED fabrication approaches. As a result, our approach has entirely eliminated any damage induced during the dry-etching processes. Our green μLED array chips exhibit a record external quantum efficiency (EQE) of 6% at ∼515 nm in the green spectral region, although our measurements have been performed on bare chips which do not have any coating, passivation, epoxy, or reflector, which are generally used for standard LED packaging in order to enhance extraction efficiency. A high luminance of >107 cd/m2 has been obtained on the μLED array bare chips. Temperature-dependent measurements show that our μLED array structure exhibits an internal quantum efficiency (IQE) of 28%. It is worth highlighting that our epitaxial approach is fully compatible with any existing microdisplay fabrication techniques.

There is a significantly increasing demand for developing III-nitride micro light-emitting diodes (μLEDs) for a wide range of applications, such as autodisplay, next generation TV, microdisplays for smartphones and smart-watches, and Augmented Reality and Virtual Reality (AR and VR) applications.[1−3] III-nitride μLEDs exhibit a number of unique features compared with organic LEDs (OLEDs) and liquid crystal displays (LCDs). Unlike LCDs, III-nitride microdisplays, where μLEDs are the key components and are self-emissive, exhibit high resolution, high efficiency, and high contrast ratio.[1−4] III-nitride μLEDs exhibit long operation lifetime and chemical robustness in comparison with OLEDs. OLEDs are typically operated at an injection current density which is several orders of magnitude lower than that of semiconductor LEDs in order to maintain a reasonable lifetime.[1−4]

In terms of the dimension requirements of μLEDs for the applications listed above, autodisplay and next-generation TV require μLEDs with a dimension of <100 μm (although smaller is better), while the μLEDs with a dimension of <50 μm (although smaller is better; ideally ≤10 μm) are essential for the other applications, in particular, AR/VR devices which require μLEDs with a dimension of <5 μm. Furthermore, μLEDs can be used for high-speed data transmission with a GHz modulation bandwidth for visible light communication (VLC) applications[5,6] due to significantly reduced junction capacitance as a result of reduced dimension compared with current standard LEDs.

III-nitride μLEDs are exclusively fabricated by means of combining a standard photolithography technique and subsequent dry-etching processes on a standard III-nitride LED wafer.[7−12] Generally speaking, surface damage will be unavoidably introduced by dry-etching processes, which enhances nonradiative recombination leading to reduction in optical performance.[13−18] This issue is minor and can be safely ignored for broad area LEDs with a dimension of >100 μm. However, this issue becomes increasingly severe with decreasing μLED dimension, eventually becoming a major factor and thus leading to severe degradation in optical performance.[14,15,19] Although sidewall passivation using dielectric materials can to some degree reduce plasma induced damage to μLEDs during dry-etching processes, the improvement is marginal even if an advanced atomic layer deposition (ALD) technique instead of a standard plasma-enhanced chemical vapor deposition (PECVD) technique is used for surface passivation.[14] In this case, an extra issue has been generated due to the passivation process, namely, the etching-back of the dielectric layer on top of the p-contact/p-GaN that also degrades electrical injection in the p-GaN region, leading to an additional challenge.[13]

Therefore, there has been a nearly complete absence of reports on μLEDs with a dimension of <5 μm so far, while μLEDs with a dimension of <5 μm are the key components for AR/VR devices. The external quantum efficiency (EQE) of the μLED with a dimension of <5 μm is very low and is limited to 1 to 5%, meaning that such μLEDs cannot offer a better efficiency than OLEDs. Very recently, blue μLEDs with a dimension of <5 μm in a square shape have been reported and have shown severe damage on the sidewalls of the μLEDs clearly observed by scanning electron microscope (SEM) measurements.[20] This also implies that the conventional fabrication approach which combines a standard photolithography technique and subsequent dry-etching processes may not work for the fabrication of ultrasmall μLEDs (with a dimension of <5 μm) with reasonably good performance.

In order to overcome the great challenge, a fundamental change in terms of epitaxial growth and fabrication is required, meaning that the conventional fabrication approach needs to be abandoned. In this work, we have reported a fundamentally different approach to any conventional fabrication methods, demonstrating ultrasmall, ultraefficient, and ultracompact green μLEDs with a dimension of 3.6 μm and an interpitch of 2 μm by developing a selective overgrowth method, namely, the selective overgrowth only takes place within prepatterned SiO2 microhole arrays with a hole diameter of 3.6 μm and an interpitch of 2 μm. The dry-etching processes for the formation of μLED mesas, which are the unavoidable steps in the conventional fabrication approaches have been completely eliminated. Furthermore, the SiO2 microhole masks also naturally serve as a kind of surface passivation without requiring any additional processes or etching-back processes, which further simplifies subsequent device fabrication. Consequently, ultrahigh brightness of above 107 cd/m2 and an ultrahigh peak EQE of 6% at ∼515 nm in the green spectral region have been achieved.

Figure shows the schematics of our invention. A standard silicon doped n-GaN layer with a thickness of 1.5 μm was initially grown on c-plane sapphire by means of any standard GaN growth approach such as the classic two-step growth method using a metal–organic vapor phase epitaxy (MOVPE) technique. This is labeled as an “as-grown n-GaN template”. Subsequently, a SiO2 dielectric film with a thickness of 500 nm was deposited on the n-GaN layer by using a standard PECVD as shown in Figure a. Afterward, by means of employing a photolithography technique and then etching processes, the dielectric layer was selectively etched down to the n-GaN surface by means of a standard inductively coupled plasma (ICP) technique, where the etching processes were carried out using a mixture of Cl2 with a flow rate of 20 sccm and Ar with a flow-rate of 30 sccm under 35 mTorr pressure at an etching power of 250 W. With this simple procedure, regularly arrayed microholes with a diameter of 3.6 μm and an interpitch of 2 μm have been formed, as depicted in Figure b.

Figure 1

Schematic of our invention (a) SiO2 mask deposition; (b) SiO2 mask patterning; (c) μLED array overgrowth; (d) plane-view and (e) cross-sectional SEM images of our regularly arrayed μLED wafer showing a diameter of 3.6 μm and an interpitch of 2 μm.

Subsequently, a standard III-nitride LED structure was grown on the SiO2 mask patterned GaN template by MOVPE; namely, a silicon doped n-GaN layer is initially grown, followed by an InGaN based prelayer (5% indium content), 5 periods of InGaN/GaN multiple quantum wells (MQWs) with 2.5 nm InGaN quantum wells and 13.5 nm GaN barriers as an active region, then a 20 nm p-type Al0.2Ga0.8N as a blocking layer and finally a 200 nm p-doped GaN layer. The total thickness of the overgrown structures is ∼500 nm, which is similar to the thickness of the SiO2 masks. Because of the dielectric masks, the LED structure can be grown within the microholes, naturally forming μLED arrays as shown in Figure c, where the diameter, the individual location, the shape, and the interpitch are fully determined by the SiO2 microhole masks without involving any μLED mesa etching processes. It means that the dimension, the individual location, the shape, and the interpitch of μLEDs are fully controlled.

Figure d,e shows typical plane-view and cross-sectional SEM images of our regularly arrayed μLEDs wafer, respectively, which demonstrate a nice circular shape with an excellent uniformity in terms of shape, diameter, and interpitch. The diameter of each μLED is 3.6 μm and the interpitch is only 2 μm. Such a small diameter and an interpitch are extremely important for manufacturing a microdisplay with a high resolution in a compact manner. Furthermore, Figure d also demonstrates a very high filling factor of our μLED wafer. The μLEDs are embedded in the SiO2 masks and have flat top faces which are nearly level with the SiO2 mask surface. It is worth highlighting that the μLED arrays are designed in such a smart manner, in which each μLED pixel shares a common n-contact and all the p-contacts are left open (which can be used in the future for indium bumps bonded to drive transistors on a silicon CMOS IC for manufacturing a microdisplay).[1] Therefore, our regularly arrayed μLED structure is fully compatible with any existing microdisplay fabrication techniques, such as the widely used pick-and-place technology[1] or a direct integration of μLED arrays with arrays of transistors that provide active-matrix switching for individually addressable μLED microdisplays.[1]

Temperature-dependent photoluminescence (PL) measurements have been carried out on the μLED sample in order to estimate its internal quantum efficiency (IQE). A 375 nm diode laser was used as an excitation source, and the emission was dispersed by a monochromator (Horiba SPEX 500M) and then detected by an air-cooled charge-coupled device (CCD). The samples were placed in a closed-cycle helium cryostat, where the temperature range can be controlled from 10 to 300 K. Figure a displays the PL spectra which have been measured as a function of temperature from 10 to 300 K, showing strong emissions at ∼520 nm in the green spectral region. Figure b shows the integrated PL intensity as a function of temperature measured under an excitation power density of 3 W/cm2, from which an IQE of 28% has been estimated.

Figure 2

Temperature-dependent PL spectra (a) and estimated IQE (b) of our regularly arrayed μLED wafer with an emission in the green spectral regions.

Here in this paper, we would like to demonstrate that our invention can be used for the fabrication of regularly arrayed μLEDs featuring ultrasmall dimensions, ultrahigh efficiency, ultrahigh brightness, and ultracompactness. Therefore, we have simply fabricated such a regularly arrayed μLED wafer into a LED device with an area of 0.1 mm2, which contains a few thousand 3.6 μm μLEDs, as schematically shown in Figure a. Transparent p-type contact was formed by depositing a layer of indium–tin-oxide (ITO) which was annealed in air at 600 °C for 1 min. Ti/Al/Ni/Au alloys were deposited as n-type contact. Ti/Au alloys were deposited as p-type and n-type electrodes. All the characteristics of our μLED chips have been measured on bare chips, meaning that no coating, no passivation, no epoxy, and no reflector are used for improving extraction efficiency.

Figure 3

(a) Schematic drawing of our green μLED array. (b) Emission microscopy images of our μLED arrays at an injection current density of 3 A/cm2 (upper: under a low magnification; bottom: under a high magnification. (c) Emission microscopy images of our μLED arrays at an injection current density of 9 A/cm2 (upper: under a low magnification; bottom: under a high magnification).

In order to clearly display emitting μLED pixels, microscopy images have been taken under a low driving current density using a micro electro-luminescence (EL) measurement system, which is equipped with two objective lenses (one with 10× magnification and NA = 0.28 and another one with 50× magnification and NA = 0.43). Figure b,c display the typical emission images of one μLED array chip at an injection current of 1 and 3 mA, corresponding to a current density of 3 A/cm2 and 9 A/cm2, respectively. Figure b,c also provide the typical emission images taken under a low and a high magnification in order to demonstrate μLED pixels clearly, showing that all individual 3.6 μm μLED pixels exhibit strong green emission under a low current density of 3 A/cm2. Taking into account the area of each μLED with a diameter of 3.6 μm, each 3.6 μm μLED can be lit up at an ultralow driving current of 0.3 μA under 2.5 V bias. It also means that the power consumption for a microdisplay, for example, with 640 × 480 pixels, is only about 0.23 W. When the injection current density is increased to 9 A/cm2, the emission is very bright. It is worth highlighting that the injection current density used for our μLEDs under operation is less than half of a typical current density (22 A/cm2) used for conventional broad area LEDs (such as 330 μm × 330 μm). This implies that the lifetime of a microdisplay, if fabricated using our μLEDs, should be at least as long as those of broad area LEDs which have an expected operation lifetime exceeding 100 000 h under normal operation conditions.[3]

Current–voltage (I–V) characteristic and electroluminescence (EL) measurements were performed on bare-chip devices at room temperature in a continuous wave (CW) mode with a Keithley 2400 sourcemeter using our microscope station.

Figure a shows the EL spectra of the μLED array bare chip measured as a function of injection current ranging from 10 to 120 mA, corresponding to the current density from 30 to 360 A/cm2. All the spectra exhibit single emission peaks at around 505–520 nm in the green spectral region, and the EL intensity increases with increasing injection current density. The inset is a typical emission image of our μLED array chip which was taken at 20 mA current, demonstrating very bright green light. Figure b displays a typical I–V characteristic of our μLED array chips as a function of forward bias, showing 20 mA injection current at 3.4 V, which is comparable to a standard broad-area InGaN LED. This also demonstrates that our μLED array chip exhibits good electrical properties. Figure c shows a typical I–V characteristic of our μLED array chip as a function of reverse bias, which examines a leakage current of the μLED array chip, demonstrating that the leakage current is as low as 4.1 μA at −4 V, corresponding to a reverse current density of 0.013 A/cm2. This leakage current density of our 3.6 μm μLED array chips is lower than that of the 10 μm blue μLEDs (not green μLEDs, and it is much more difficult to fabricate green μLEDs than blue μLEDs) fabricated by the conventional μLED fabrication approach along with an extra passivation process using advanced ALD technique,[14] although the diameter of our μLEDs is much smaller. This further confirms the major advantages of our invention in terms of electrical performance.

Figure 4

(a) EL spectra of a μLED chip measured as a function of injection current at room temperature. Inset: Emission photo of a μLED array chip taken at 20 mA. (b) I–V characteristics of a μLED array chip as a function of forward bias. (c) I–V characteristics of a μLED array chip as a function of reverse bias.

Light output powers and luminous flux were measured in a CW mode on TO5-header bonded bare-chip LEDs (namely, without any surface coating, passivation, epoxy, or reflector involved) using a LCS-100 characterization system equipped with an integrating sphere and a CCD APRAR spectrometer. Figure a shows the luminance of our μLED array chip as a function of injection current density, demonstrating that high luminance of above 1 × 107 cd/m2 has been achieved, which is 2–3 orders of magnitude higher in comparison with current OLEDs or LCDs.[4]Figure b exhibits a typical EQE of our μLED array bare chip as a function of injection current density of up to 400 A/cm2, demonstrating a peak EQE of ∼6%, which is a record EQE compared with any existing report on μLEDs in the green spectral region.[2−4,13] Furthermore, Figure also indicates that our ultrasmall μLEDs without any heat-sink components involved can sustain a high current density of above 400 A/cm2, further confirming the material quality of our grown μLEDs obtained using our invention. Please note that the measurements were performed on a bare chip without any package or coating. Based on our experience, it is expected that the EQE can be further increased if a proper package which can significantly improve extraction efficiency is made (extraction efficiency could be enhanced by a factor of 2).

Figure 5

(a) Brightness of our μLED array chip as a function of injection current density; (b) EQE of our μLED array chip as a function of injection current density. Please note that the measurements are performed on a bare chip without any package or coating.

In summary, we have demonstrated a completely different approach which allows us to achieve ultrasmall, ultraefficient, and ultracompact μLEDs with a dimension of down to 3.6 μm and an interpitch of down to 2 μm. Our invention is based on an overgrowth on prepatterned templates with SiO2 microhole arrays, thus eliminating all the drawbacks of the conventional μLED fabrication approaches. As a result, a record peak EQE of 6% at ∼515 nm in the green spectral regions has been achieved on our μLED array bare chips. A high luminance of >107 cd/m2 has been obtained. Temperature-dependent measurements show an internal quantum efficiency of 28% for our μLED array structure.