A fluorinated alloy-type interfacial layer enabled by metal fluoride nanoparticle modification for stabilizing Li metal anodes.

Using highly dispersed metal fluoride nanoparticles to construct a uniform fluorinated alloy type interfacial layer on the surface of Li metal anodes is realized by an ex situ solution chemical modification method. The fluorinated alloy-type interfacial layer can effectively inhibit the growth of undesirable Li dendrites while enhancing the performance of Li metal anodes. This journal is © The Royal Society of Chemistry 2019.

Lithium metal batteries (LMBs) are considered as one of the most attractive candidates for next generation energy storage systems due to the high energy density provided by Li metal anodes.1–3 However, the uncontrolled growth of Li dendrites on the surface of Li metal anodes would lead to piercing of the separator and cause a battery short-circuit, which severely hinders the practical applications of LMBs.4 The growth of Li dendrites mainly stems from an inhomogeneous and fragile interfacial layer formed via spontaneous reaction between Li metal and the electrolyte, which is named the solid electrolyte interphase (SEI).5 The SEI layer plays a vital role in inhibiting further reaction between the Li metal anode and the electrolyte due to its electron-insulating and ion-conducting properties. The fabrication of an electrochemically and mechanically stable SEI layer on the surface of Li metal anodes is presently considered as one of the most effective strategies to stabilize Li metal anodes. To fully functionalize the SEI layer on the surface of Li metal anodes, the SEI layer should also possess high elastic modulus, high thermodynamic stability, and a dense structure.6

In the past decade, much effort has been devoted to achieving desirable properties in SEI layers. Various electrolyte additives,7–9 all-fluorinated non-aqueous electrolytes10,11 and new-type lithium salts with a fluorine group12,13 have been introduced to reinforce the SEI layer and such a highly fluoridated protective layer was found to be highly effective for suppressing the growth of Li dendrites. It has also been demonstrated that the electrochemical performance and stability of LMBs can be improved impressively in the presence of inorganic fluorides (LiF) or organic fluorides (C–F).14 However, fluorinated additives and new-type salts used in the electrolytes are usually too expensive. Besides the in situ formation of advanced SEI layers by electrolyte modification, an ex situ fabrication of an artificial solid electrolyte interphase (ASEI) layer on the surface of Li metal anodes has been developed in the past few years. ASEI layers including hollow carbon spheres,15 two dimensional materials,16,17 functional polymers,18–20 nanocomposites,21,22 atomic layer deposition (ALD) layers23,24 and so on7,25–29 were used to stabilize Li metal anodes. To some extent, these attempts have shown encouraging results to stabilize the surface of Li metal anodes during battery cycling. However, these ASEI layers cannot simultaneously possess high thermodynamic stability, good ionic conductivity, and capability of guiding Li metal deposition at one time to maximize their roles.

More recently, Li-based alloy type interfacial layers30 have been ex situ modified on the surface of Li metal anodes to guide uniform Li plating/stripping, leading to the improved cycling stability of Li metal anodes. The drawback of the alloy type layer is its limited electronic insulation to maintain the long term stability during repeated Li stripping/plating. In addition, as an important component in previously reported SEI layers, lithium fluoride (LiF) is highly electron-insulating and ultra-thermodynamically stable to reinforce the stability of SEI layers.6 It will be very interesting to combine LiF with Li-based alloy layers30–33 to further improve the performance of ASEI layers. However, the ex situ modification of these combined ASEI layers is rarely reported due to the very low dissolubility of metal fluorides in the electrolyte. To make indissoluble materials highly dispersible in the solution, adopting the nanoparticle form is an efficient pathway. We also found that metal fluoride nanoparticles can be synthesized by a facile solution method34 on a large scale, implying that the cost of these nanoparticles is much lower than that of the fluorinated organics7–9 for the ex situ chemical modification of Li metal anodes.

Herein, we report the fabrication of a functional LiF/Li–M alloy layer on the surface of a Li metal anode via ex situ chemical modifications facilitated by highly dispersible metal fluoride nanoparticles (MF NPs, M = Zn, Ca, Mg or Al). Based on the synergistic effect of the as-formed LiF/Li–M alloy composite layer, the protected Li metal anode exhibited an excellent cycling stability of 500 hours in symmetrical cells at a high current density of 1 mA cm–2 in conventional carbonate solvent based liquid electrolytes. Moreover, the LMB composed of the protected Li metal anode and LiNi0.8Co0.15Al0.05O2 (NCA) cathode displayed improved cycling stability (147.5 mA h g–1) in comparison to that of the pristine LMB (20 mA h g–1) at 0.5C after 150 cycles.

We carried out an ex situ chemical modification strategy to fabricate a functional LiF/Li–M alloy layer on the surface of the Li metal anode via immersing fresh Li metal foil into a suspension of MF NPs (Fig. 1a). The MF NPs were prepared by a facile solution method (for details please see the Experimental section†). The transmission electron microscopy (TEM) images and X-ray diffraction (XRD) patterns show that the MF NPs synthesized by this facile solution method are uniform in size and pure phases (Fig. S1, ESI†). Most importantly, the obtained MF NPs are highly dispersible in the co-solvent of 1,3-dioxolane/1,2-dimethoxyethane (DOL/DME, 1 : 1, v/v) as shown in Fig. S2 (ESI†), which can promote the reaction between MF NPs and fresh Li metal foil. The uniform ASEI protective layer consisting of LiF/Li–M alloy compounds can be built via the following reaction:Li + MF → LiF + Li–M (M = Zn, Ca, Mg, Al)

Fig. 1

(a) Schematic illustration of the ASEI layer formation via ex situ chemical modification. (b) Optical photographs of Li foil treated with co-solvent (DOL/DME) and co-solvent dispersed ZnF2 NPs, respectively.

As shown in Fig. 1b, a uniform black layer on the Li-metal surface can be obtained after being treated with the solution in which zinc fluoride nanoparticles (ZnF2 NPs) were evenly dispersed. In contrast, there is no obvious change of fresh Li metal foil after being treated using pure DOL/DME co-solvent under the same conditions. The obvious distinction observed in Fig. 1b profoundly proves that the black protective layer is the product originating from the reaction between ZnF2 NPs and Li metal in DOL/DME solution. Furthermore, the optical photos of protected Li metal foil obtained by the treatment of other MF NPs (M = Ca, Mg, Al) in Fig. S3 (ESI†) indicate the versatility of our proposed ex situ chemical modifications on the Li metal anode.

Scanning electron microscopy (SEM) was employed to analyze the surface morphological features of the Li metal anode after the treatment with MF NPs. The top-view and side-view SEM images (Fig. 2a–f and S4–S6, ESI†) of Li metal foil treated with MF NPs both demonstrate that the uniform ASEI protective layers can be obtained by our developed nanoparticle treated strategy. In terms of Li metal foil treated with ZnF2 NPs, the ASEI protective layer is compact as shown in the top-view SEM images (Fig. 2a and b). The designed compact layer can effectively prevent the Li metal anode contact with the electrolyte, thereby suppressing uncontrolled side reactions and the consumption of the electrolyte. Besides, the thickness of the as-fabricated ASEI protective layer was measured to be 5–10 μm as shown in the side-view SEM images (Fig. 2d and e), in which the LiF/Li–Zn alloy layer on the top is marked by cyan colour and the lithium under the alloy layer is marked by green colour. The obtained structure is similar to that of other reports related to the ASEI protective layer.35

Fig. 2

(a and b) The top-view SEM images, (c) corresponding EDX mapping analysis, (d and e) side-view SEM images and (f) corresponding EDX mapping analysis of ZnF2 NPs – treated Li metal anodes, respectively. The modified layer is denoted by cyan colour and the Li is denoted by green colour. (g and h) The Zn 2p, F 1s XPS analysis of the corresponding ASEI layer.

The components of the as-fabricated ASEI protective layer were further revealed by energy dispersive X-ray spectroscopy (EDX) mapping. As shown in Fig. 2c and f, F and Zn are homogeneously dispersed in the ASEI protective layer indicating that a uniform coating of the LiF/Li–Zn alloy layer was formed on the surface of the Li metal anode. Moreover, X-ray photoelectron spectroscopy (XPS) was used to explore the compositions and chemical bonding information in the ASEI protective layer (Fig. 2g and h). As shown in Fig. 2g, the XPS spectrum of the Zn 2p orbital splits into two peaks at 1022.3 and 1045.4 eV, which belong to Zn 2p3/2 and Zn 2p1/2, respectively, corresponding to the Zn in the Li–Zn alloy.36 Besides, the XPS signal of the F 1s split can be fitted to the peak located at 685.0 eV, which is attributed to the formation of LiF.32 The results of EDX mapping and XPS can validly indicate that the as-formed ASEI protective layer is composed of the products of the reaction between the ZnF2 NPs and Li metal. Other MF NPs also show similar results on the surface of Li metal anodes to the ZnF2 NPs, and the analytical data such as EDX and XPS are shown in Fig. S4–S6 (ESI†), respectively. All these results demonstrate that the high reactivity and good dispersability of MF NPs (M = Zn, Ca, Mg, Al) can be used to realize the construction of the ASEI protective layer via an efficient solution chemical reaction with active Li metal.

The effectiveness of the as-formed ASEI protective layer for promoting the cycling stability of the Li metal anode was first revealed by the polarization voltage evolution behavior in symmetric cells. Fig. 3a and b show the huge difference in the behavior of polarization voltage variation as a function of time at a relatively high current density (1 mA cm–2) between the pristine Li metal anode and protected Li metal anode by the LiF/Li–Zn alloy layer. The pristine Li metal anode exhibits a high polarization voltage (∼200 mV) within 150–220 h and gradually increases to 400 mV after 300 h cycling, indicating that the migration of lithium ions is severely impeded by the interface failure (top of Fig. 3a). In contrast, the Li metal anodes treated with ZnF2 NPs display long and stable voltage curves (∼50 mV within initial 220 h cycling) and can be cycled up to 400 h with a polarization voltage less than 100 mV (bottom of Fig. 3a). In terms of cycle performances within 300–320 h as shown in Fig. 3b, the polarization voltage increases sharply and becomes unstable in the pristine Li metal anode, indicating the rapid degradation of the interface, whereas the protected Li metal still exhibits an extremely stable voltage profile with a low polarization voltage of ∼70 mV. Besides, other MF NP modifications also have a similar function of stabilizing deposition behavior on the surface of Li metal anodes to the ZnF2 NPs (Fig. S7, ESI†). In our study system, the activation process may be related to the surface side reactions of the as-formed protective layer and the electrolyte. After the side reaction, a relatively stable solid electrolyte interphase (SEI) layer formed on the Li metal anode, leading to the stable plating/stripping cycling with a relatively lower overpotential. With the prolongation of cycling, the ASEI layer on the surface of Li metal was gradually damaged due to the repeated volume change of the Li metal anode and the overpotential increased. Thus, it seems that the polarization of the Li metal anode decreased to a lower value in the middle of the test. The obvious difference of plating/stripping voltage evolution of the pristine Li metal anode and protected Li metal anode during the cycling implies that the Li plating/stripping efficiency is promoted by the LiF/Li–M alloy layer, which can be attributed to the improved lithium ion surface transport by LiF30 and preferred Li nucleation sites in the Li–M alloy layer. Our developed LiF/alloy ASEI protective layer displayed the best efficiency to stabilize the Li metal anode among the recent reports using conventional carbonate solvent based liquid electrolytes (details in Table S1, ESI†). The reduced polarization voltage of our ASEI layer protected lithium metal anode is also superior to the previous reports of solely LiF reinforced SEI layer protected Li metal anodes and comparable to the alloy layer protected Li metal anodes.31,37,38

Fig. 3

(a) The evolution of voltage profiles of symmetric cells based on the pristine Li metal anode (top) and ZnF2 NPs – treated Li metal anodes (bottom), respectively. (b) The corresponding voltage profiles of (a) in an enlarged view of 300–320 h. (c) The Zn 2p, F 1s XPS spectra of the ASEI layer formed on Li foil after the 10th cycle. (d) The surface and side-view SEM images of the pristine Li metal anode and ZnF2 NPs – treated Li metal anodes after 320 h cycling.

In order to further verify the stability of the as-fabricated ASEI protective layer during the cycling, XPS was used to characterize the chemical information of the ASEI protective layer after the first ten cycles. As shown in Fig. 3c, there is no obvious variation in the peak positions and intensities of Zn and F. The emergence of a small C–F peak can be observed due to the initial decomposition of the electrolyte during the activation process.32,39 The XPS results similar to those of the electrode before cycling (Fig. 2g and h) indicate that the LiF/Li–Zn alloy layer is stable during the Li plating/stripping processes. This also means that the LiF/Li–Zn alloy layer can not only effectively suppress the growth of Li dendrites but also prevent the contact between the underlying Li metal and the electrolyte to form extra thick and fragile SEI layers.

The surface morphology characterization by SEM shows that significant Li dendritic growth occurred on the surface of the pristine Li metal anode (Fig. 3d and S8, ESI†). In contrast, the protected Li metal anode by the LiF/Li–M (M = Zn, Al) alloy layer after 160 and 320 h cycling still maintains a relatively smooth surface without dendrites (Fig. 3d, S9 and S10, ESI†). Based on the SEM images and EDX mapping results of the Li metal anode at the different cycling times (Fig. S11, ESI†), we can conclude that the protective layer can be maintained on the surface of the Li metal anode after short or long term cycling. This again indicates the stability and effectivity of our designed ASEI protective layer. In addition, the interfacial resistance of both the protected Li metal anode by the ASEI layer and the pristine Li metal anode exhibits a relatively small impedance before cycling (Fig. S12, ESI†), confirming that the introduction of the ASEI protective layer does not deteriorate charge transfer at the interface. But the interfacial impedance of the pristine Li metal anode increases to 284 Ω after 320 h cycling, which corresponds to a rapid increase in the polarization voltage (Fig. 3a and b), indicating the high diffusion resistance of Li+ ions at the interface due to the rough surface and thickened SEI layer. In contrast, the protected Li metal anodes show no obvious change in the impedance before and after cycling, which is consistent with the smooth surface of protected Li metal anodes after cycling. The rapid ion diffusion and stable interfaces cause the low diffusion impedance of Li+ ions under the effect of the ASEI protective layer during the plating/stripping process. Therefore, the LiF/Li–M alloy layer can effectively protect the Li metal anode providing the long-term cycling stability of the symmetric cells.

The full Li-metal-based cells (NCA/Li) were assembled and tested to demonstrate the effectiveness of the LiF/Li–M alloy layer in LMBs. As shown in Fig. 4a, the initial discharge specific capacities of all cells are higher than 200 mA h g–1. The difference between initial discharge and charge capacity of the NCA cathode is caused by the uncontrolled side reactions between the electrode and electrolyte.40 In the 150-cycle test at 0.5C (1C = 200 mA g–1, 1C means a current density at which the theoretical specific capacity of the electrode material can be achieved in one hour), there is a significant performance difference between the cells based on the pristine Li metal anode and protected Li metal anode. The cell of all LiF/L–M alloy layers protected Li metal anodes can maintain stable discharge capacities with very slow capacity decay. By contrast, the discharge capacity of the cell using the pristine Li metal anode shows rapid decrease of capacity, which drops to nearly 20 mA h g–1 in the 150th cycle. Detailed comparison of charge/discharge voltage profiles further indicates that the polarization of the full cell based on the protected Li metal anode is lower than that of the cell using the pristine Li metal anode (Fig. 4b and c). In particular, after the 150th cycle, the polarization of the cell using the protected Li metal anode did not increase significantly but that of the cell using the pristine Li metal anode increased very much. The significantly improved cycling stability of the cell using the protected Li metal anode verified the effectiveness of the as-formed ASEI protective layers in practical LMBs.

Fig. 4

(a) Electrochemical cycling performance at 0.5C and (b and c) representative charge/discharge profiles of cells based on the pristine Li metal anode and MF NPs – treated Li metal anodes in the 10th and 150th cycle, respectively.

In summary, we have proposed a MF NP induced functional modification strategy to fabricate a LiF/Li–M (M = Zn, Ca, Mg, Al) alloy ASEI layer for stabilizing Li metal anodes. Due to the high activity of MF NPs, the LiF/Li–M alloy layer can be simultaneously formed on the surface of the Li metal anode by the reaction between MF NPs and Li metal. The ASEI protective layer can effectively inhibit the growth of Li dendrites at a high current density of 1 mA cm–2, realizing the long lifespan of 150 cycles in NCA matched LMBs. Our developed MF NP induced LiF/Li–M alloy ASEI layer will open a new avenue to construct artificial protective layers on Li metal anodes via the chemical modification of rationally designed nanoparticles.

Conflicts of interest

There are no conflicts to declare.

Click here for additional data file.