A Ioannidis1, D Bomze2, C H F Hämmerle3, J Hüsler4, O Birrer5, S Mühlemann3. 1. Clinic of Reconstructive Dentistry, Center of Dental Medicine, Switzerland. Electronic address: alexis.ioannidis@zzm.uzh.ch. 2. Lithoz GmbH, Vienna, Austria. 3. Clinic of Reconstructive Dentistry, Center of Dental Medicine, Switzerland. 4. Department of Mathematical Statistics, University of Bern, Switzerland. 5. Master Student, Center of Dental Medicine, University of Zurich, Switzerland.
Abstract
OBJECTIVES: The load-bearing capacity of ultra-thin occlusal veneers made of 3D-printed zirconia were compared to the ones obtained by fabricating these reconstructions by CAD/CAM milling zirconia or heat-pressing lithium-disilicate. METHODS: On 60 extracted human molars, the occlusal enamel was removed and extended into dentin. Occlusal veneers of 0.5 mm thickness were digitally designed. The specimens were divided into 3 groups (n = 20 each) differing in the restorative material and the fabrication technique of the occlusal veneer. (1) 3DP: 3D-printed zirconia (Lithoz); (2): CAM: milled zirconia (Ceramill Zolid FX); (3) HPR: heat-pressed lithium disilicate (IPS e.max Press). After conditioning procedures, the restorations were adhesively bonded onto the conditioned tooth. Thereafter, all specimens were aged in a chewing simulator by exposure to cyclic fatigue and temperature variations. Subsequently the specimens were statically loaded and the load which was necessary to decrease the maximum load by 20% and initiate a crack (Finitial) and the load which was needed to fracture the specimen (Fmax) were measured. Differences between the groups were compared applying the Kruskal-Wallis (KW) test and the Wilcoxon-Mann-Whitney-Test (WMW: p < 0.05). RESULTS: The median Finitial values for the groups 3DP, CAM and HPR were 1'650 N, 1'250 N and 500 N. The differences between all three groups were statistically significant (KW: p < 0.0001). The median Fmax values amounted to 2'026 N for the group 3DP, 1'500 N for the group CAM and 1'555 N for the group HPR. Significant differences were found between 3DP and CAM (WMW: p = 0.0238). SIGNIFICANCE: Regarding their load-bearing capacity, 3D-printed or milled zirconia as well as heat-pressed lithium disilicate can be recommended as restorative material for ultra-thin occlusal veneers to prosthetically compensate for occlusal tooth wear. Despite statistically significant differences between the restoration materials, all load-bearing capacities exceeded the clinically expected normal bite forces.
OBJECTIVES: The load-bearing capacity of ultra-thin occlusal veneers made of 3D-printed zirconia were compared to the ones obtained by fabricating these reconstructions by CAD/CAM milling zirconia or heat-pressing lithium-disilicate. METHODS: On 60 extracted human molars, the occlusal enamel was removed and extended into dentin. Occlusal veneers of 0.5 mm thickness were digitally designed. The specimens were divided into 3 groups (n = 20 each) differing in the restorative material and the fabrication technique of the occlusal veneer. (1) 3DP: 3D-printed zirconia (Lithoz); (2): CAM: milled zirconia (Ceramill Zolid FX); (3) HPR: heat-pressed lithium disilicate (IPS e.max Press). After conditioning procedures, the restorations were adhesively bonded onto the conditioned tooth. Thereafter, all specimens were aged in a chewing simulator by exposure to cyclic fatigue and temperature variations. Subsequently the specimens were statically loaded and the load which was necessary to decrease the maximum load by 20% and initiate a crack (Finitial) and the load which was needed to fracture the specimen (Fmax) were measured. Differences between the groups were compared applying the Kruskal-Wallis (KW) test and the Wilcoxon-Mann-Whitney-Test (WMW: p < 0.05). RESULTS: The median Finitial values for the groups 3DP, CAM and HPR were 1'650 N, 1'250 N and 500 N. The differences between all three groups were statistically significant (KW: p < 0.0001). The median Fmax values amounted to 2'026 N for the group 3DP, 1'500 N for the group CAM and 1'555 N for the group HPR. Significant differences were found between 3DP and CAM (WMW: p = 0.0238). SIGNIFICANCE: Regarding their load-bearing capacity, 3D-printed or milled zirconia as well as heat-pressed lithium disilicate can be recommended as restorative material for ultra-thin occlusal veneers to prosthetically compensate for occlusal tooth wear. Despite statistically significant differences between the restoration materials, all load-bearing capacities exceeded the clinically expected normal bite forces.
Authors: Alvaro Della Bona; Viviane Cantelli; Vitor T Britto; Kaue F Collares; Jeffrey W Stansbury Journal: Dent Mater Date: 2021-01-19 Impact factor: 5.304