Literature DB >> 31382459

Recent Progress on Transition Metal Nitrides Nanoparticles as Heterogeneous Catalysts.

Abstract

This short ren>view aims at providing an overview of the most recent literature regarding transition metal nitrides (TMN) applied in heterogeneous catalysis. These materials have received renewed attention in the last decade due to its potential to substitute noble metals mainly in biomass and energy transformations, the decomposition of ammonia being one of the most studied reactions. The reactions considered in this review are limited to thermal catalysis. However the potential of these materials spreads to other key applications as photo- and electrocatalysis in hydrogen and oxygen evolution reactions. Mono, binary and exceptionally ternary metal nitrides have been synthetized and evaluated as catalysts and, in some cases, promoters are added to the structure in an attempt to improve their catalytic performance. The objective of the latest research is finding new synthesis methods that allow to obtain smaller metal nanoparticles and increase the surface area to improve their activity, selectivity and stability under reaction conditions. After a brief introduction and description of the most employed synthetic methods, the review has been divided in the application of transition metal nitrides in the following reactions: hydrotreatment, oxidation and ammonia synthesis and decomposition.

Entities: Chemical Disease Species

Keywords: heterogeneous catalysis; transition metal nitrides

Year: 2019 PMID： 31382459 PMCID： PMC6722748 DOI： 10.3390/nano9081111

Source DB: PubMed Journal: Nanomaterials (Basel) ISSN： 2079-4991 Impact factor: 5.076

1. Introduction

In the last decade strong interen>st has emerged in the field of nitrogen-doped catalysts, especially since new carbon nanostructures have been successfully synthetized. In those structures nitrogen can be easily inserted as heteroatoms due to its similarity to carbon, and as a doping agent it offers new possibilities in the field of catalysis [1]. Nitrogen confers basic sites for optimal reactant adsorption and an excellent electron density that may improve the catalytic performance due to the better dispersion of the active phase and the changes in the electronic properties [2]. Transition <n class="Chemical">span class="Chemical">metal nitrides have been tradition<spn>an class="Chemical">ally employed as catalysts in reactions such as hydrodesulfurization or ammonia synthesis [3]. Nowadays, researchers face new challenges in catalytic transformations to find active and selective catalysts in the fields of energy or biomass including reactions such as hydrodeoxygenation, water-gas shift and CO and CO2 hydrogenation among others [4]. Noble <n class="Chemical">span class="Chemical">metals have been widely studied on those <spn>an class="Chemical">reactions. However economical catalysts based on abundant materials are more suitable for industrial applications. Hence, the need of searching new catalyst able to replace noble metals and the positive effect of nitrogen doping in several transformations, have brought up renewable attention to transition metal nitrides. These materials can donate electrons from the nitrogen atom and possesses high chemical, mechanical and thermal stability. Also importantly for thermal catalytic applications, when optimal synthesis conditions are employed, nitrides can reach relatively high surface areas of at least 90 m2/g [5]. Transition metal nitrides are compounds in which nitrogen is incorporated into the interstitial sites of the metal structure. Since the size of the nitrogen atom is small (0.065 nm), it fulfills the Hägg rule (i.e., the ratio of the radii of non-metal to metal is less than 0.59, this allowing the formation of simple typical structures as compiled in Figure 1 [6].

Figure 1

Value of the nitrogen chemical potential (μN) where the nitrogen covered surface becomes more stable than the clean metal surface; Reproduced from [18], with permission from American Chemical Society, 2018.

As it can be expected the reactivity of the resulting transition metal nitride is different from that of the parent metal. In general, two main effects can be considered when nitrides are used in catalysis [7,8]: Ligand effect: Nitrides have a different electronic structure compared to the parent metal. This is due to the charge transfer from the metal to the non-metal, hybridization of the metal d-states with the non-metal sp-states, and expansion of the metal–metal lattice spacing. These changes in the electronic structure, modify the chemical reactivity of the parent metal so that the strenght of adsorption of reactants and products is similar to noble metals, this improving the selectivity of the reactions. Ensemble effect: When nitrogen is located on the metal surface, it may decrease the number of available metal sites, also creating different adorption sites. This effect can be somehow tuned by changing the metal to nitrogen ratio.

2. Synthesis and Structural Properties

Metal nitrides can be prepared among other methods by thermal treatment of the metal precursor obtained from template methods [9], ball milling [10,11] or temperature programmed reaction/reduction procedures [12]. Template methods are based on the use of a sacrificial template, normally MgO, to which a mixture containing the metal precursor is added followed by thermal treatment at high temperatures and extensive wash to remove the MgO template. In this way Metal-N entities are well dispersed in a carbon based matrix. In the ball milling method, the solid metal precursor either commercial or lab-made are submitted to milling under pressure and connected to a supply of the nitridation agent, N2 or NH3. So far, the most employed method to synthetize transition <n class="Chemical">span class="Chemical">metal nitrides is a temperatu<spn>an class="Chemical">re programmed reaction/reduction procedure. The method consists in a reductive nitriding treatment under a gas flow (i.e., NH3 or a mixture of N2:H2) of the corresponding metal oxide precursor to produce the nitride [12]. The characteristics of the final nitride depend on the precursor and preparation conditions such as heating rate and final temperature. It was reported that higher areas are obtained when heating rates below 1 °C/min and/or high gas space velocity (150,000 h−1) are used, as these conditions reduce sintering due to water release [13,14]. Other nitrogen sources such as urea or m-phenylenediamine have been employed in order to improve the efficiency of the nitridation [15,16]. The use of nitrogen-rich transition metal nitrides in catalysis is very promising. However, the synthesis of TMN with high nitrogen to metal ratio is energetically demanding. This has prompted researchers to find aternative methodologies and new structures such as polymorphs of Zr3N4, Hf3N4, Ta2N3, and noble metal dinitrides OsN2, IrN2, and PtN2 have been explored [17]. Saun>tet et al. [18] recently studied the nitridation of transition metal surfaces and tried to offer some insight into the synthesis and stability of transition metal nitrides under working conditions. The authors studied fifteen transition metals and using theoretical and experimental techniques evaluated the extent of nitridation (surface vs. bulk) depending on the metal and the shape of nanoparticles. By using the nitrogen chemical potential at which metal covered by nitrogen is more stable than bare metal, the authors were able to stablish a nitridation trend among the studied serie. As depicted in Figure 1, Mo, W, Fe and Re are more easily nitrided, becomign more difficult when moving to the right hand side of the periodic table, i.e., less oxophilic metals, which agrees well with previous experimental results [19,20]. The most studied transition <n class="Chemical">span class="Chemical">metal nitride in cat<spn>an class="Chemical">alysis is molybdenum. In general cubic γ-MoNx (0.5 ≤ x < 1) is obtained by NH3 treatment of the oxide precursor, MoO3, while mixtures of H2 + N2 lead to the formation of tetragonal β-MoNx (x ≤ 0.5) or γ-MoNx. Hexagonal δ-MoNx (x ≥ 1) is obtained from MoS2 and NH3. Similarly, the content of nitrogen on iron nitrides influences their structure, so upon increasing the nitrogen content, the lattice structure changes from fcc γ’-Fe4N to hcp ε-FexN (2 < x ≤ 3) and to orthorhombic ζ-Fe2N. In Figure 2, the most common structures of transition metal nitrides are shown.

Figure 2

(a) bcc: TiN, ZrN, HfN, VN, CrN; (b) hcp: Mo2N, W2N; (c) fcc: MoN, TaN. Blue points represent transition metal atoms and brown points nitrogen atoms. Adapted from [6], with permission from Wiley, 2013.

3. Transition Metal Nitrides as Catalyst

3.1. Hydrotreatment Reactions

Transition <n class="Chemical">span class="Chemical">metal nitrides a<spn>an class="Chemical">re considered excellent candidates to replace noble metals in hydrogen-treatment reactions since they show similar or even better performance than noble metals. It has been reported that Mo nitrides can easily chemisorb hydrogen due to the contraction of the d-band and the changes in the electron density that result as a consequence of the interstitial incorporation of N in the Mo metal lattice. Moreover, in the Mo2N-based catalysts hydrogenation reaction occurs over nitrogen vacancies, so Mo/N ratio also influences the catalytic performance [21]. Both COn> and CO2 hydrogenations are very interesting reactions since they overcome key environmental challenges while providing energy or valuable chemicals. On the one hand CO hydrogenation can be employed to purify H2 gas streams before feeding to fuel cells to avoid poisoning. On the other hand, CO2 hydrogenation has been appointed as a solution to reduce the amount of CO2 evolved to the atmosphere from the industrial activity and convert it to fuels and chemicals [22,23]. However COn> and CO2 hydrogenation face several challenges. CO2 activation is difficult due to the inert nature of the molecule and the cleavage of the C−O bonds in CO2 demands high activation energy. Also, methanation of CO and CO2 which provides an efficient alternative to conventional natural gas, is highly exotermic. The produced reaction heat favours metal sintering, which decreases the catalyst activity. Catalyst deactivation can also take place when carbon deposits on the active phase. Zaman et al. [24,25] have studied the influence of adding alkali promoters to the Mo2N systems in CO hydrogenation. The synthesis in both cases was performed by a simple temperature programmed treatment of the molybdenum and alkali precursors under ammonia flow. This leads to a material containing a mix of different phases: Mo, Mo2N, Mo oxide and alkali-Mo oxide phase. The promotion with alkalis favoured the conversion to oxygenates, i.e., methanol, ethanol and propanol. Cesium was found to be better promoter to oxygenates at 5% wt. (28% selectivity to oxygenates vs. 11% with Li promoted and 6.5% with unpromoted). The lower selectivity achieved with Li compared to Cs was attributed to the formation of Li2MoO4 phases during nitridation. On the other hand, baren> Mo2N leads to the preferential conversion of CO to hydrocarbons, which can be ascribed to (i) CO dissociative hydrogenation and (ii) water-gas shift reaction, as shown in Figure 3. However, the presence of alkali hinders CO dissociation, which benefits the molecular insertion of CO into—CHx intermediate and promotes the coupling of alcohols.

Figure 3

Plausible CO hydrogenation reaction pathways on Mo2N and K-Mo2N catalysts. Reproduced from [25] with permission from Elsevier, 2018.

Ren>garding the effect of alkali loading, the authors performed a thorough study with potassium as promoter using several weight percentages: 0.45, 1.3, 3 and 6.2% [24]. The best selectivity to oxygenates, 44%, was obtained over promoted K-Mo2N with a K/Mo surface ratio of 0.06 which also corresponded to the best K distribution among the samples. The XRD showed that both γ-Mo2N cubic and monoclinic K2MoO4 were formed and this latter phase seems to increase upon K addition further than 3% wt, this being detrimental for K distribution and hence for oxygenates conversion. Methanation, is the catalytic hydrogenation of carbon oxides (CO and CO2) to obtain synthetic natural gas. Ru, Rh and Ni catalysts have proven to offer good catalytic performance in terms of activity and selectivity to methane which can be further improved by using bimetallic systems and optimizing catalyst synthesis method [26]. Methanation and hydrodesulfurization of dibenzothiophenen> was studied over molybdenum nitride by Zhao et al. [27]. The authors were able to synthetize a rich nitrogen molybdenum nitride using high pressure, 3.5 GPa, through a solid-state ion exchange reaction. This new nitride, 3R−MoN2 holds a rhombohedral R3m structure, isotypic with MoS2. However it offered catalytic activities three times higher than MoS2 for the hydrodesulfurization of dibenzothiophene and over twice as high in the sour methanation of syngas at 723 K. The binary nitride, Ni2Mo3N, was studied by Leybo et al. [28] in the methanation of CO2. Yet, modest selectivites to CH4, ca. 20%, were obtained and the active phase suffered sintering upon reaction conditions, decreasing the stability of the catalyst. Besides <n class="Chemical">span class="Chemical">molybdenum other <spn>an class="Chemical">metal nitrides have been tested in methanation reaction. For example co-methanation of CO and CO2 have been evaluated by Li et al. [29] over cobalt nitrides supported on alumina. The authors studied the effect of metal loading on Co4N/γ-Al2O3 and Co/γ-Al2O3 catalysts. According to the characterization, the cobalt nitride favoured stronger interactions with the support, this improving the dispersion of the nanoparticles and also their resistance to coking and metal sintering after 250 h which, as previously mentioned, is critical in such a exotermic reaction. Moreover, it was confirmed that the nitrogen atoms improved the adsorption of reactants due to their basicity, leading to better catalytic performance compared to the Co metal supported catalysts. The better results were also explained by the uniform metal dispersion and superior metal-support interaction. Fisher-Tropsh is a well-known transformation to con>nvert syngas, CO + H2, into liquid hydrocarbons and that was very relevant in catalytic research in the 70–80s due to the oil crisis. Now, it has revised attention since it can also use syngas from biomass to produce fuels and chemicals. The most studied systems are those based on iron as they offer optimal results under a variety of conditions that allow to tune the selectivity, and are economically interesting. However, under reactions conditions the water produced can oxidize the catalyst with its subsequent deactivation [30]. Bao et aln>. [31] studied the confination effect of FeN cubic nanoparticles inside carbon nanotubes (FexN-in) (see Figure 4). Firstly, FeN supported on CNT resulted 5–7 times more active than FeN supported on silica and metallic Fe on CNT. This seems to be related to the better stability of the nitrides under CO hydrogenation conditions compared to metallic and carbide iron which are oxidized by water, resulting in catalyst deactivation. Also, the catalyst where FeN nanoparticles were selectively loaded inside the CNT was more active than the catalyst with FeN nanoparticles mainly dipersed on the external walls, FexN-out, (1.4 times). The authors explained the better activity of the confined nanoparticles by the lower particle size and the formation of more FeCxN1x entities on FexN-in than on FexN-out during reaction, leading to stronger retention of nitrogen atoms in the lattice.

Figure 4

Reproduced from [32], with permission from Royal Society of Chemistry, 2011.

In con>ntrast to the activity and stability enhancement of iron nitride compared to its parent metal, cobalt nitride seems to be a poison for FT synthesis. In literature it was reported that by adding a nitrogen source such as acetonitrile or ammonia to the FT gas feed, cobalt nitride phases are formed which result in catalyst deactivation by deposition on the most active metallic cobalt sites (steps and edges) [32]. So far, theoretical results have predicted that CO adsorption and dissociation over γ-Mo2N(111) has a similar activation barrier to that of MoS2, so similar activity for syngas conversion can be expected [33]. CO2n> dry reforming of methane (DRM) has received much attention, as it transforms two greenhouse gases (CH4 and CO2) into syngas. The most studied catalysts have been noble metals, Ru, Rh and non-noble metals such as Ni [34]. Some reports appeared using transition metal carbides due to their low cost and similar structure compared to noble metals. However at atmospheric pressure, carbides can easily be deactivated due to oxidation by CO2 or H2O [35]. Hence, alternatively nitrides have been tested as potential catalysts for DRM. Gu et aln>. [36] studied Mo2N, Ni3Mo3N and Co3Mo3N above 550 °C and atmospheric pressures and found that a synergic effect is observed in the bimetallic nitrides that improve the activity and resistance to oxidation and coke deposition on the DRM compared to the monometallic nitride Mo2N. The most active and stable catalyst was Co3Mo3N which, among other factors, was ascribed to the synergistic effect between the Mo and interstitial metal Co. Owing to environn>mental concerns and the depletion of fossil resources, in the last decade researchers have focus on the study of biomass derived compounds to obtain fuels and chemicals. Since the starting lignocellulosic biomass owns a high oxygen concentration (>50%), most of the transformations require selective removal of oxygen. More specifically, one of the most studied reactions is hydrodeoxygenation (HDO). Under HDO condititions, the reactants can be also converted through the decarboxylation/decarbonylation (DCO) path, promoting the C−C cleaveage which is undesirable for fuels and chemicals. For example, Monnier et aln>. [37] studied the conversion of oleic acid and canola oil with nitrides of Mo, W, and V supported on γ-Al2O3. The Mo2N catalyst exhibited superior activity for oleic acid conversion compared to the other nitride catalysts, and also favored the HDO route vs. DCO. The HDO path produces preferentially n-C18H38 (diesel fuel cetane enhancers). Also, Mo2N/γ-Al2O3 was stable in continuous hydrotreatment of canola oil at 400 °C under 83 bar hydrogen, reaching a constant yield of 50% middle distillates. Murzin et aln>. [38] studied Ni and Mo2N-MoO2 on the HDO of more complex reactants, Chlorella algal oil extracted with supercritical hexane and stearic acid, at 300 °C under 30 bar in the presence of hydrogen. The catalysts were selective to fatty acids, indicating deactivation of decarbonylation sites. The catalyst Mo2N-MoO2, despite being less active than the Ni based catalysts, was more stable and it showed no deactivation after a 360 min test. These results open new possibilities that should be explored regarding mixtures of nitrides and oxides. Nitrides are known to be deactivated in the presence of water due to oxidation, but these oxides might tolerate better the presence of impurities, enhancing their stability. Zhang et aln>. [39] prepared cobalt nitride supported on a nitrogen doped carbon CoNx@NC using cellulose and ammonia as the carbon and nitrogen source respectively at different synthesis temperatures from 500 to 800 °C. The catalysts were tested in the HDO of eugenol at 2 MPa H2 and 200 °C. According to the reaction results, the reaction follows different paths when using nitrides or metallic cobalt. While the nitrides favour the cleaveage of the C-aryl−OCH3 bond to form 4-propylphenol, metallic cobalt promotes the hydrogenation of the alkene moiety. The best catalyst was CoNx@NC-650 which displayed the largest surface area and dispersion of the nitrides nanoparticles. The catalyst was also successfully tested to promote the HDO of phenolic compounds. Supported CoNx on carbon nanotubes on the hydrogenation of nitrobenzene and hydrogenated coupling of nitrobenzene with benzaldehyde was studied by Zhang et al. [40] as schematized in Figure 5. Some catalytic tests verified that catalytic activity was mainly due to the CoNx entities and the authors also suggested that the activity was mainly due to the cobalt chelate complexes bonded to nitrogen atoms of the graphene lattice.

Figure 5

CoNC/CNT active sites on nitro compounds hydrogenation and hydrogenated coupling of nitrobenzene with benzaldehyde. Reproduced from [41], with permission from Royal Society of Chemistry, 2016.

Lodeng et aln>. [41] compared the activity of molybdenum nitride, carbide, and phosphide supported on TiO2 on the HDO of phenol at 25 bar and in a temperature range between 350 and 450 °C. All the catalysts were highly active to benzene and only minor amounts of aromatic ring hydrogenation were obtained. Molybdenum nitride displayed lower activity compared to its carbide and phosphide counterparts, but its selectivity to cyclohexene was higher than that of phosphide and similar to carbide. Hydrogenn>ation of −COH moieties constitutes one of the most interesting and studied reactions in fine chemistry since it allows obtaining a high number of compounds that are used for example in pharmaceuticals and/or fragances. Reactants such as cinnamaldehyde or crotonaldehyde have been widely studied in an attempt to heterogeneized the catalytic system. The catalysts must be selective to the unsaturated alcohols without reducing the C=C bonds. With that aim heterogeneous catalysts based on noble metals mainly Ru, Pd and Pt have been widely investigated with good results in terms of activity and selectivity [42] and the significant role of nitrogen improving the selectivity to the desired products have also been reported [43]. To date, these specific transformations has been tested with bimetallic systems of metal nitrides and noble metals. Fu et aln>. [44] have used a previously functionalized support to obtain small nitrides nanoparticles supported on the mesoporous silica SBA-15. The synthesis of Mo2N over SBA-15 started by functionalizing the support with a monoamine that is located homogeneously into the pores of the support as shown ion Figure 6. This amine is then used as anchoring point for the molybdenum precursors which preferentially adsorbs on the moieties. Then, the procedure follows the previously explained temperature reduction procedure in NH3. Finally the noble metal is impregnated and reduced with NaBH4 forming bimetallic phases with Mo2N. In this way, Mo2N and Pt nanoparticles with a size of about 8.0 and 5-6 nm respectively were obtained with metal loadings of Mo (22% wt.) and Pt (3% wt.).

Figure 6

Synthesis of Pt-Mo2N-SAB-15. Reproduced from [45], with permission from American Chemical Society, 2016.

Then, Pt/Mo2N/SBA-15 with different Pt loadings (1–3% wt.) was tested in the chemoselective hydrogenation of cinnamaldehyde. Both activity and selectivity to the cinnamyl alcohol was higher over Pt/Mo2N-based catalysts than over monometallic Pt/SBA-15, that the authors ascribed to the synergy between Pt and Mo2N nanoparticles and the more efficient use of the Pt surface on the bimetallic sample. In the work of Thomson et aln>. [45], some more insight was given regarding the reaction mechanism and nature of active phases. To do so, the authors used a thorough experiment by hydrogenating a high surface area γ-Mo2N to obtain a partially hydrogenated entity γ-Mo2N-Hx. Then, by combining H2-TPD experiments and DFT simulations three different hydrogen species were identified: surface nitrogen bound (κ1-NHsurf), surface Mo bound (κ1-MoHsurf) and subsurface Mo-bound (μ6-Mo6Hsub). The ren>activity of these species was assessed by testing them in the hydrogenation of crotonaldehyde. Accordingly, the authors proposed that reaction starts by a heterolytic dissociation of H2 to form surface NH (κ1-NHsurf) and MoH (κ1-MoHsurf) as schematized in Figure 7. Then, since subsurface interstitial H site (μ6-MoHsub) is more energetically favored than surface κ1-MoHsurf, hydrogen migrates into the lattice. Moreover, based on the catalytic results the authors proposed that surface and subsurface species MoH (κ1-MoHsurf/μ6-MoHsub) are more selective to the hydrogenation of the C=O bond and the surface κ1-NHsurf sites hydrogenate preferentially the C=C bond.

Figure 7

Reproduced from [45], with permission from American Chemical Society, 2016.

The selective hydrogenation of acetylene to ethylene is an important transformation since ethylene is the monomer to produce polyethylene polymers and it has a strategic relevance in refineries, being critical its high purity production. The cataln>ytic behaviour of β- and γ-Mo2N in the partial hydrogenation of acetylene was evaluated by Lizana et al. [46] that studied the influence of synthesis parameters on textural properties of the nitrides and its effect on the catalytic performance. The results showed that selectivity of both β- and γ-Mo2N was higher than over Pd-based catalysts. Also, β-Mo2N which displays higher surface Mo/N ratio compared to γ-Mo2N, offered lower selectivity to partial hydrogenation and a two-fold higher specific acetylene hydrogenation rate. Altarawneh et al. [47], used computational methods to study mechanism of the selective hydrogenation C2H2 over γ-Mo2N to C2H4 rather than complete hydrogenation to the corresponding alkane. Reactions take place through H2 adsorption followed by dissociation. The authors obtained the modes of H2 adsorption as shown in Figure 8: 3-fold hollow fcc (H1) and 4-fold hollow fcc (H3) sites over the (111) and (100) terminations of γ-Mo2N, respectively.

Figure 8

H2 adsorption sites on Mo2N (111) and (100) faces. Reproduced from [48], with permission from American Chemical Society, 2016.

In agreement with experimental results, this work seems to confirm that dissociation of H2 occurs over nitrogen vacancies. It is also proposed that the lower stability of the partial hydrogenated molecule, C2H4 leads the selectivity. Another interesting reaction within fine chemistry is the hydrogenation of nitroaromatic compounds, since aromatic haloamines are important intermediates in the manufacturing of drugs, pesticides, and pigments among others. The reaction has been successfully performed over Au [48], Ir [49] and Pd [50] catalysts supported over a variety of materials. Keane et al. [51] demonstrated experimentally that Mo2N improved the performance of Au in the selective hydrogenation of p-chloronitrobenzene (p-CNB) to p-chloroaniline (p-CAN) reaching 100% selectivity to p-CAN, a four-fold higher hydrogenation rate compared to Au/Al2O3 and showed stability upon several cycles. The system Pd/Mo2N was an effective catalyst for the hydrogenation of p-nitrophenol (PNP) to p-aminophenol (PAP) [52]. In this study, the authors synthetized Pd/Mo2N nanoparticles of 2–3 nm size over SBA-15. The high dispersion improved the interaction between Pd and the nitride so that 1 wt% Pd–Mo2N/SBA-15 showed better catalytic performance than 1 wt% Pd/SBA-15 and 20 wt% Pd/SBA-15. In Figure 9 the proposed reaction mechanism over the Pd–Mo2N/SBA-15 is shown.

Figure 9

Catalytic conversion mechanism of PNP into PAP over the Pd–Mo2N/SBA-15 hybrids in the presence of NaBH4. Reproduced from [53], with permission from American Chemical Society, 2018.

Wu et aln>. [53] reported a green solvent-free synthesis method for CoNx entities supported on doped mesoporous carbon materials (CoNx-OMC) with surface areas in the range 678–1250 m2/g, high N content (4.3–10.8 wt%) and rich in CoNx sites as verified by XPS. The optimized CoNx-OMC, thermally treated at 800 °C) catalyst showed an interesting catalytic performance on the hydrogenation of several nitro compounds, i.e., 100% conversion, almost 100% selectivity and stable upon recycling, under mild conditions (5 bar H2 pressure, 110 °C). According to the catalytic and characterization results, a synergy effect is reached between CoNx sites and the nitrogen doped support. On the one hand, the CoNx entity provides specific sites for the adsorption and activation of nitro groups. On the other hand, the nitrogen heteroatoms of the support act as anchoring sites, increasing the dispersion of the active components and facilitating mass transportation. Also, it was confirmed that cobalt nitride was responsible of the activity and not the metallic Co nanoparticles. Density function<n class="Chemical">span class="Chemical">al theory c<spn>an class="Chemical">alculations were performed by Altarawneh et al. [54] who studied the hydrogenation of p-CNB to p-CAN over the model γ-Mo2N(111) surface. The results showed that adsorption of p-CNB is thermodynamically favoured over Mo-hollow face-centered cubic (fcc) and N-hollow hexagonal close-packed (hcp) sites with adsorption energies of −32.1 and −38.5 kcal/mol, respectively. Also, the results are in agreement with previous experimental reports that described a high selectivity to p-CAN at low temperatures, the direct path being preferential versus the condensation route [55]. The theoretical results suggest that activated hydrogen, H*, is transferred from both fcc and hcp hollow sites to the NO/−NH groups, the hydrogenation of chloronitrosobenzene being the rate-limiting step with an energetic barrier of 55.8 kcal/mol. Also, the high energy barrier for direct fission of the C−Cl bond excludes the formation of aniline. Another industrialn> transformation of acetylene is the hydrochlorination to obtain vinyl chloride monomer (VCM), the basic unit of polyvinyl chloride (PVC). Industrially this reaction is performed using HgCl2 as catalyst, however due to environmental and health concerns, alternative systems have been evaluated [56]. Among them, noble metal, i.e., Au, Pd, Pt and Ru over activated carbon, have been the most studied, gold being the best in terms of activity and selectivity. Since it has been previously found that nitrogen doping can promote adsorption for HCl [57], which is the VCM synthesis reaction rate-controlling step, a potential catalytic system is that consisting of metal nitrides. Dai et aln>. [58] studied V, Mo, and W nitrides (10 wt% metal loading) supported on activated carbon. Their experiments showed that VN/AC offered very low activity in the reaction. Mo2N was initially the most active, but deactivated with time to give lower conversion values than those reached with W2N/AC. The selectivity to C2H3Cl was similar for all the tested nitrides and reached near 100%. To further explain these results, TPD of the reactants, C2H2 and HCl, was performed and showed that W2N/AC dislayed a stronger and similar interaction with both reactants, compared to the other catalysts. However, Mo2N/AC which deactivates during reaction, showed an easy desorption of HCl and difficult desorption of C2H2, this producing significant amounts of coke which can be responsible of the observed deactivation. The aun>thors also studied binary Mo and Ti nitrides with different Mo/Ti ratios supported on activated carbon for acetylene hydrochlorination [59]. All the binary nitrides displayed better catalytic performance compared to the mononitrides and a Mo/Ti ratio of 3 was optimal among the studied systems offering 89% conversion and selectivity over 98.5%. Apparently a synergy effect among Mo and Ti occurs so that adsorption of HCl is enhanced while adsorption of acetylene is reduced. Other chloro compounds have been evaluated with TMN. For example Keane et al. [60] studied the gas phase hydrodechlorination of 1,3-dichlorobenzene (1,3-DCB) using molybdenum and tungsten carbide (Mo2C, W2C) and nitride (Mo2N). fcc-Mo2N showed better activity (by a factor of 20) compared to pure hcp- and fcc-carbides, that displayed similar activity.

3.2. Oxidation

The selective oxidation of carbon monoxiden> with low concentration of O2 (CO-PROX) is used to purify hydrogen rich streams obtained from hydrocarbon reforming. So far, the most studied and active system are the CuO–CeO2 and Pt based catalyst [61]. With the aim of finding moren> economical active and selective catalysts, the catalytic performance of several transition metal nitrides have been assessed. For example, Yang et al. [62] studied the effect of Co loading (1 to 10 wt%) on Co4N supported on γ-Al2O3. The cobalt nitrides displayed similar activities compared Pt-group metals in the temperature range 200–220 °C. The sample 3 wt% Co/γ-Al2O3 offered the best activity and selectivity in PROX reaction which could be related to the higher concentration nitrogen vacancies in the near-surface that enhance the adsorption of reactants. Selective oxidation of alcohols plays an important role in many industrial transformations such as energy conversion and storage or the production of fine chemicals. The most studied and active catalysts are supported Au Pt, Pd, Ag and Ru and other non-noble-metal catalysts such as Co and Cu [63]. In order to test moren> economically viable alternatives Deng et al. [64] evaluated the catalytic activity of iron nitride, FeN4, supported on graphene in the oxidation of benzene using H2O2 as oxidant. The characterization suggested that atomically dispersed FeN4 were obtained and these entities were also stable after reaction. The catalyst reached 23.4% conversion and 18.7% yield of phenol at room temperature, however no comparison with other catalyst is given. Later, Yuan et aln>. [65] studied several metal nitrides (MNx/C-T, M = Fe, Co, Cu, Cr, and Ni) synthetized at different pyrolysis temperatures, T, in the oxidation of unsaturated alcohols. The most active and selective catalyst to the corresponding aldehydes was the iron nitride. Among them, the catalysts prepared by thermal treatment at 900 °C displayed the better catalytic performance in the selective oxidation of HMF to DFF with almost complete conversion and selectivity exceeding 97%. According to the characterization performed the authors suggested that when thermal treatment was performed at lower temperatures, c.a. 600 °C, a higher concentration of nitrogen doped carbon was formed, in detriment of iron nitride; and that nitrogen doped carbon offered lower activity. In contrast, the formation of FeN4 was favored at higher synthesis temperatures, resulting in materials that offered better activity. Moreover, the activity of the recycled catalysts could be restored by thermal treatment under NH3/N2. With the aim of gaining moren> insight into the active sites of the Fe−N−C catalysts. Zhang et al. [9] studied atomically dispersed Fe−N−C catalyst synthetized using nano-MgO as a template. The catalysts were tested in the selective oxidation of the C−H bond of a wide range of aromatics, heterocyclic, and aliphatic alkanes at room temperature. The catalysts showed high activity and selectivity of up to 99%, as well as great reusability. The atomical dispersion of FeNx (x = 4 − 6) was verified using sub-Ångström-resolution HAADF-STEM along with XPS, XAS, ESR, and Mössbauer spectroscopy. The authors also reported that the concentration of each FeNx species depends on the pyrolysis temperature. Among the studied samples, the most active was Fe−N−C-700 which is comprised of high-spin FeN6 (28.3%), low-spin FeN6 (53.8%), and medium-spin FeN5 (17.9%) species, as shown in Figure 10. This latter is over one order of magnitude more active than the other two species. Upon increasing the pyrolysis temperature, the concentration of FeN5 decreases to less than 10%, leading to lower activity.

Figure 10

Reproduced from [9], with permission from American Chemical Society, 2017.

3.3. Ammonia Synthesis and Decomposition

The production of ammonian> through the Haber–Bosch Process was a technological breakthough of the last century since it is a relatively easy way of obtaining a synthetic fertiliser. The process uses promoted iron catalyst to produce ammonia from N2 and H2 at temperatures of ca 400 °C and high pressure of around 100–200 atmospheres. The process of ammonia synthesis is so relevant that it currently consumes near 1–2% of the world’s energy demand [66]. This data reveals that more efforts can be made to optimize the process as small changes on the reaction conditions could have a huge impact on global energy consumption. Thus, despite being a well-known process, several attempts have been performed to obtain more active and stable catalysts to work under milder conditions [67]. In the last decades binary and ternary transition <n class="Chemical">span class="Chemical">metal nitrides of the type Mo, <spn>an class="Chemical">Co and Fe have been tested in both ammonia decomposition and ammonia synthesis. Simulations and experimental tests have shown that cobalt molybdenum nitride, Co3Mo3N can be the most active catalyst for ammonia synthesis, superior to the industrial iron catalyst and promoted ruthenium catalyst [68,69]. The synthesis of <n class="Chemical">span class="Chemical">ammonia cat<spn>an class="Chemical">alyzed by molybdenum nitride seems to be a structure-sensitive reaction so that the bigger the particle size, the higher the intrinsic activity of the catalyst [70]. On the other hand, the effect of the nanoparticle morphology does not seem to be so clear. Sun et al. studied the synthesis of ammonia over plate-like γ-Mo2N and nanorod β-Mo2N and γ-Mo2N [71] and did not find significant differences among them. Also, the synthesis conditions limit the comparison since residual sulphur from the molybdenum precursor, Mo2S, can poison the catalyst. In order to increase the dispersion of the nitrides and improve the stability, Ding et al. [72] synthetized molybdenum nitride supported on HZSM-5, using MoOx as precursor and NH3 as nitriding agent at 973 K. In this way molybdenum oxide exchanges with hydroxyl groups on the zeolite surface and obtained a Mo to N ratio close to 2. The authors proved that this supported molybdenum nitrides are more stable against oxidation by comparing with unsupported catalysts. The resulting catalyst, MoNx/ZSM-5, displayed excellent activity in the ammonia synthesis under ambient pressure. A kinetic approach showed that the apparent activation energy for ammonia synthesis on MoNx/ZSM-5 is around 20% lower than that on bulk Mo2N (9.8 kcal/mol vs. 12.4 kcal/mol). Interen>stingly, the effect of reaction pressure was different on bulk Mo2N and MoNx/ZSM-5, i.e., higher reaction pressures are more favorable on the MoNx/ZSM-5 catalyst than on γ-Mo2N. The authors suggested that this difference could be due to the interaction of nitrogen with the zeolite framework, acting as an equivalent pressure which may enhance the pressure effect on the ammonia synthesis. Another significant finding of this work is that upon increasing the Si/Al ratio of the zeolite, the catalytic activity of MoNx increases. Recently, Catlow et al. [73] used DFT calculations to evaluate the associative and dissociative mechanisms of ammonia synthesis over Co3Mo3N. The results showed that in the associative mechanism, Eley-Rideal/Mars van Krevelen, hydrogen reacts with nitrogen adsorbed and activated on the surface to generate ammonia. Promotion of cobalt molybdenum nitridesn> with other elements have been also studied. According to Paweł Adamski [74] chromium and potassium were able to generate a well-developed porous structure, increasing the activity of the catalysts in ammonia synthesis by 50% compared to the non-promoted catalyst. Ammonian> decomposition has become a strategic research topic since it allows to obtain CO free hydrogen to feed fuel cells. Ammonia can also be employed directly as fuel in vehicles since it has a high energy density (8.9 kW h/kg), is easily liquified at room temperature and low pressure, i.e., less than 10 bar, and its narrow combustion range allows safe operation. Many cataytic monometallic and bimetallic systems have been tested based on Fe, Ni, Co, Ru, Ir, Pt or Rh, supported on several materials. Among them, ruthenium catalysts supported on different carbon materials such as active carbon, carbon nanotubes showed the highest activity. In aln>l cases, researchers observed a low activity for ammonia decomposition reaction at temperatures below 400 °C, since recombinative desorption rate of the adsorbed N atoms from active metals is slow at those conditions [75]. Also, hydrogen molecule seems to cover active sites over Ni- and Ru catalysts, this hindering the ammonia decomposition reaction. Hence, despite being well studied systems, the temperatures required and the use of noble metals should be avoided to make the process technical and economically feasible. Eguchi et aln>. [76], studied the effect of a second transition metal on Mo nitride based catalysts, prepared by temperature-programmed reaction under NH3 flow of the oxides precursors: MoO3, CoMoO4, NiMoO4, and FeMoO4. Incorporation of the second metal into the Mo nitride resulted in a significant decrease in the surface area (3.1–8.8 vs. 80 of Mo2N). However, the area of Mo2N was reduced to 23 m2/g after reaction, indicating that the material was not stable under the reaction conditions. Despite the lower surface area, the addition of a second metal was beneficial for ammonia decomposition and the activity followed the trend Co3Mo3N > Ni3Mo3N > Fe3Mo3N > Mo2N. Several transition metal nitrides have been studied for ammonia decomposition, being the binary system metal-cobalt molybdenum nitride the most interesting among them [77,78,79,80,81]. Based on the n class="Chemical">NH3-TPSR <spn>an class="Chemical">results, the authors suggested that the addition of Co and Fe favoured the desorption of hydrogen. However, over Mo2N de desorption of nitrogen was slower since nitrogen atoms tend to interact stronger with the nitride. According to the results the authors concluded that the order in which each metal nitride system dissociates metal nitride–N bond was Co3Mo3N ≈ Ni3Mo3N > Fe3Mo3N > Mo2N. Moreover, the presence of Co, Ni, and Fe improves the stability against poisoning by H2 on the active sites and the best results are obtained when doped catalysts are employed. In order to improve the surfacn>e area of nitrides, alternative synthesis paths have been explored. For example Podila et al. [77] studied the use of citric acid as chelating agent to prepare bulk Co3Mo3N, with surface areas in the range 93–129 m2/g. The use of citric acid (CA) as chelating agent afforded better nitride dispersion which resulted in better catalytic performance. An optimal concentration of citric acid was related to a higher surface area, lower particle size and increased proportion of Mo2N and Co3Mo3N phases, so that when the CA/Mo ratio was changed from 1 to 3 in the synthesis, the conversion increased from 75% to 97% at 550 °C. Similarly Zaman et al. synthetized nickel [78] and cobalt molybdenum nitrides [79] using citric acid and compared its catalytic performance on ammonia decomposition with that obtained employing γ-Mo2N. Under these synthesis conditions, the surface area of the binary nitrides was increased but still below 20 m2/g. According to the results both catalyst, Ni2Mo3N and Co3Mo3N offered over 97% conversion, while the use of pure γ-Mo2N resulted in 50–70% conversion under the same experimental conditions. Zhao et aln>. [80] used supported binary CoMo nitrides over several porous materials with different physico-chemical characteristics: CNTs, Al2O3, activated carbon and 5A Zolite. The experimental procedure was a simple impregnation of the precursors followed by a temperature-programmed reaction in N2–H2. The activity followed the order: CoMoNx/CNTs > CoMoNx/Zeolite 5 > CoMoNx/AC > CoMoNx/Al2O3. However, despite the clear better performance of CNT, the supports differ in many features such as surface chemical composition and morphology, making the comparison and related conclusions quite difficult. The effen>ct of synthesis conditions, nitridation temperature and iron loading was also evaluated in iron nitrides supported on carbon nanotubes [81]. A higher synthesis temperature of ca. 500 °C and Fe loading of 10% prepared under NH3 flow resulted in well-dispersed Fe2N nanoparticles which exists along with Fe2O3 entities and offered the best ammonia conversion among the catalysts tested. In contrast the synthesis under a N2/H2 flow resulted in the formation of both Fe2N and Fe4N, this latter species being detrimental for ammonia decomposition.

4. Conclusions

This short ren>view of the most recent literature has shown that transition metal nitrides possess a wide spectrum of catalytic applications with interesting catalytic performance. The review has focused on thermal heterogeneous catalysis which requires high surface areas and good dispersion of the active phase. Despite the significant advances done up to date, there is plenty of room for research on transition metal nitrides to optimize the synthesis conditions in order to obtain higher surface areas and better nanoparticles dispersion, ideally reducing the synthesis temperature. Aln>so, further work to improve the stability will be required in order to obtain potential industrial catalysts. One of the main reason for deactivation is the oxidation of the nitrides, which is likely to occur in reactions that generate water such as carbon dioxide hydrogenation, or when water is already in the reactants mixtures as it happens with biomass transformations. In this sense, it seems that subsurface hydrogen can delay deactivation and more insight into this reaction mechanism would allow to propose regeneration mechanism. Again, the use of a high surface area support for transition metal nitrides nanoparticles can improve the dispersion of the active phase and potentially improve their stability upon reaction conditions against sintering and oxidation. The improved cataln>ytic performance that has been reached with more complex systems that incorporate a second or third metal, should be complemented with deeper understanding of the actual active phase and the chemical structure of the nitrides. Similarly, the use of promoters like alkalis and its effect of the structure need to be further studied since these materials have also demonstrated a significant potential for future catalytic applications. However, there is still no clear correlation mainly due to the complexity of these systems and difficulties to perform in situ investigations.

5 in total

Recent Progress on Transition Metal Nitrides Nanoparticles as Heterogeneous Catalysts.

1. Introduction

2. Synthesis and Structural Properties

3. Transition Metal Nitrides as Catalyst

3.1. Hydrotreatment Reactions

3.2. Oxidation

3.3. Ammonia Synthesis and Decomposition

4. Conclusions

Review 1. Surveying the Synthesis, Optical Properties and Photocatalytic Activity of Cu₃N Nanomaterials.

2. DFT Investigation of Ammonia Formation via a Langmuir-Hinshelwood Mechanism on Mo-Terminated δ-MoN(0001).

3. Hydrocracking of crude palm oil to a biofuel using zirconium nitride and zirconium phosphide-modified bentonite.

Review 4. Interstitial and substitutional light elements in transition metals for heterogeneous catalysis.

5. Preparation of Aluminum-Molybdenum Alloy Thin Film Oxide and Study of Molecular CO + NO Conversion on Its Surface.

Recent Progress on Transition Metal Nitrides Nanoparticles as Heterogeneous Catalysts.

1. Introduction

2. Synthesis and Structural Properties

3. Transition Metal Nitrides as Catalyst

3.1. Hydrotreatment Reactions

3.2. Oxidation

3.3. Ammonia Synthesis and Decomposition

4. Conclusions

Review 1. Surveying the Synthesis, Optical Properties and Photocatalytic Activity of Cu3N Nanomaterials.

2. DFT Investigation of Ammonia Formation via a Langmuir-Hinshelwood Mechanism on Mo-Terminated δ-MoN(0001).

3. Hydrocracking of crude palm oil to a biofuel using zirconium nitride and zirconium phosphide-modified bentonite.

Review 4. Interstitial and substitutional light elements in transition metals for heterogeneous catalysis.

5. Preparation of Aluminum-Molybdenum Alloy Thin Film Oxide and Study of Molecular CO + NO Conversion on Its Surface.

Review 1. Surveying the Synthesis, Optical Properties and Photocatalytic Activity of Cu₃N Nanomaterials.