Fahim Vohra1, Nawaf Labban2, Abeer Al-Hussaini3, Maha Al-Jarboua3, Rahaf Zawawi3, Ali Alrahlah4, Mustafa Naseem5. 1. 1Department of Prosthetic Dental Science, College of Dentistry, King Saud University, Eng. Abdullah Bugshan Research Chair for Dental and Oral Rehabilitation, Riyadh, Saudi Arabia. 2. 2Department of Prosthetic Dental Science, College of Dentistry, King Saud University, Riyadh, Saudi Arabia. 3. 3Interns, College of Dentistry, King Saud University, Riyadh, Saudi Arabia. 4. 4Department of Restorative Dental Science, College of Dentistry, King Saud University, Eng. Abdullah Bugshan Research Chair for Dental and Oral Rehabilitation, Riyadh, Saudi Arabia. 5. 5Department of Preventive Dental Sciences, Dar Al Uloom University, Riyadh, Saudi Arabia.
Abstract
Objective: The aim of this study was to assess the effect of Er;Cr:YSGG laser parameters (power and frequency) on the bond strength and color stability of lithium disilicate (LD) ceramics. Materials and methods: One hundred ten specimens of LD ceramic were fabricated following heat pressed technique. Fifty disks were randomly distributed into five groups according to types of surface treatment [hydrofluoric (HF) acid, L1S L2S, L1D, and L2D]. For all laser-treated groups, bond preparation settings were used with a gold hand piece using a MZ10 tip (Er;Cr:YSGG, water lase I plus; Biolase). After surface treatment, adhesive bond was applied, and after photopolymerization, a composite buildup was performed. To evaluate shear bond strength, a controlled force was applied until failure using a universal testing machine. Color stability was assessed for six groups (HF, L1S L2S, L1D, L2D, and control) of LD ceramic (shade A1, LT translucency) through the CIE L*a*b* system. Three specimens from each of the six groups were selected randomly for assessment of surface topography using scanning electron microscopy. Means and standard deviations were compared using analysis of variance and Tukey's post hoc test (p < 0.05). Results: The maximum and minimum mean bond strength were shown by the L2D group 19.95 ± 1.014 and L1S group specimens 14.68 ± 0.863, respectively. Highest mean ΔE was found in L2S group 8.17 ± 2.10 and the lowest mean ΔE was found in control group (no treatment) 0.11 ± 0.05. Conclusions: LD specimens lased (Er;Cr:YSGG) with 3.75 W power and 15 Hz frequency for 4 min showed bond strength comparable with HF acid samples, and color changes within acceptable range (ΔE 1.17). Laser treatment (Er;Cr:YSGG) at 3.75 W power and 15 Hz frequency for 4 min of LD ceramics appears to be clinically efficient, showing acceptable bond strength and color stability.
Objective: The aim of this study was to assess the effect of Er;Cr:YSGG laser parameters (power and frequency) on the bond strength and color stability of lithium disilicate (LD) ceramics. Materials and methods: One hundred ten specimens of LD ceramic were fabricated following heat pressed technique. Fifty disks were randomly distributed into five groups according to types of surface treatment [hydrofluoric (HF) acid, L1S L2S, L1D, and L2D]. For all laser-treated groups, bond preparation settings were used with a gold hand piece using a MZ10 tip (Er;Cr:YSGG, water lase I plus; Biolase). After surface treatment, adhesive bond was applied, and after photopolymerization, a composite buildup was performed. To evaluate shear bond strength, a controlled force was applied until failure using a universal testing machine. Color stability was assessed for six groups (HF, L1S L2S, L1D, L2D, and control) of LD ceramic (shade A1, LT translucency) through the CIE L*a*b* system. Three specimens from each of the six groups were selected randomly for assessment of surface topography using scanning electron microscopy. Means and standard deviations were compared using analysis of variance and Tukey's post hoc test (p < 0.05). Results: The maximum and minimum mean bond strength were shown by the L2D group 19.95 ± 1.014 and L1S group specimens 14.68 ± 0.863, respectively. Highest mean ΔE was found in L2S group 8.17 ± 2.10 and the lowest mean ΔE was found in control group (no treatment) 0.11 ± 0.05. Conclusions: LD specimens lased (Er;Cr:YSGG) with 3.75 W power and 15 Hz frequency for 4 min showed bond strength comparable with HF acid samples, and color changes within acceptable range (ΔE 1.17). Laser treatment (Er;Cr:YSGG) at 3.75 W power and 15 Hz frequency for 4 min of LD ceramics appears to be clinically efficient, showing acceptable bond strength and color stability.
Entities:
Keywords:
Er;Cr:YSGG laser; ceramic; color stability; lithium disilicate; shear bond strength
Authors: Samer Al-Saleh; Turki W Aboghosh; Mousa S Hazazi; Khalid A Binsaeed; Abdulaziz M Almuhaisen; Huda I Tulbah; Amal S Al-Qahtani; Sara Shabib; Mashael Binhasan; Fahim Vohra; Tariq Abduljabbar Journal: Polymers (Basel) Date: 2021-12-02 Impact factor: 4.329
Authors: Fayez Hussain Niazi; Zeeshan Qamar; Mohammed Noushad; Abdullah Khaled Bin Muhareb Journal: Pak J Med Sci Date: 2022 Jan-Feb Impact factor: 1.088
Authors: Amal S Al-Qahtani; Huda I Tulbah; Mashael Binhasan; Sara Shabib; Khulud A Al-Aali; Mai M Alhamdan; Tariq Abduljabbar Journal: Nanomaterials (Basel) Date: 2022-03-03 Impact factor: 5.076
Authors: Mohammed S Bin-Shuwaish; Yasser F AlFawaz; Hamad A AlGamaiah; Abdulaziz S AlSani; Ibrahim B Abobakr; Khaled M Alzahrani; Basil Almutairi; Esraa A Attar; Fahim Vohra; Tariq Abduljabbar Journal: Int J Environ Res Public Health Date: 2021-03-08 Impact factor: 3.390