A comprehensive prediction and evaluation method of pilot workload.

BACKGROUND: The prediction and evaluation of pilot workload is a key problem in human factor airworthiness of cockpit.
OBJECTIVE: A pilot traffic pattern task was designed in a flight simulation environment in order to carry out the pilot workload prediction and improve the evaluation method.
METHODS: The prediction of typical flight subtasks and dynamic workloads (cruise, approach, and landing) were built up based on multiple resource theory, and a favorable validity was achieved by the correlation analysis verification between sensitive physiological data and the predicted value.
RESULTS: Statistical analysis indicated that eye movement indices (fixation frequency, mean fixation time, saccade frequency, mean saccade time, and mean pupil diameter), Electrocardiogram indices (mean normal-to-normal interval and the ratio between low frequency and sum of low frequency and high frequency), and Electrodermal Activity indices (mean tonic and mean phasic) were all sensitive to typical workloads of subjects.
CONCLUSION: A multinominal logistic regression model based on combination of physiological indices (fixation frequency, mean normal-to-normal interval, the ratio between low frequency and sum of low frequency and high frequency, and mean tonic) was constructed, and the discriminate accuracy was comparatively ideal with a rate of 84.85%.

Introduction

Research indicated that humans were the cause of more than 2/3 aviation accidents [1]. Based on this information, to guarantee safety, Federal Aviation Administration (FAA) in Federal Aviation Regulation (FAR) 25.771 and FAR 25.1523 stated the related requirements of pilot workload [2]. The promotion and application of Head-Up Display (HUD) technique has been used to solve the allocation of attention resource problems induced by the frequent alternation between head down display and head up to the target outside the cockpit. But certain difficulties in ergonomics need to be further optimized and solved, such as fatigue based on visual coding, confusion caused by vision overlay, and spatial orientation caused by single color display [3, 4]. Subjective assessment was the primary method for the certification of pilot workload, and the physiological method can also be accepted for reference [3].

Researchers claimed that during a flight task, the fixation and saccade behavior of eye movements are closely related to pilot workload and attention allocation [5, 6]. When dealing with a visual task the pilot’s blinking pattern changes; the pupil dilation and cognitive workload in a human-computer interaction task were closely connected [7, 8]. The Low Frequency (LF) and High Frequency (HF) elements of Heart Rate Variability (HRV) indicated the activation of sympathetic nerve and parasympathetic nerve system, and in the actual flight task, the HF increased as the task difficulty increased [9]. The ratio between LF and HF (LF/HF) decreased as the task difficulty increased, which reflects the balance between the sympathetic nerve and parasympathetic nerve system [7, 10]. The stimulation of the sympathetic nerve system speeds up skin’s metabolism and the secretion of sweat glands, and the increase of perspiration can lead to a higher Electrodermal Activity (EDA) response in a complicated flight task [11]. When compared with assessments based on the single index, a comprehensive evaluation that combines eye movement, Electrocardiogram (ECG) data, and other physiological measurements can achieve better results [9, 12].

The Timeline Analysis and Prediction (TLAP) method and McCrachen-Aldrich (M-A) prediction technology [13] were two major prediction methods of task workload. The multiple resource theory [14] was widely acknowledged in the prediction of workload, and a combination of them has been done in our research to realize a theoretical prediction of workload. There were many research groups globally who relied on mathematical modeling in order to discriminate the pilot workload status. The major workload models include discriminant analysis [15, 16], regression analysis [17] and support vector machine (SVM) model [18], but the modeling of dynamic flight task based on HUD simulation was relatively rare. Nowadays, pilot discrimination models face several major setbacks, such as relatively stronger subjective factors, the undesirable consequences of single or comprehensive physiological indices, and the high expenses of physiological equipment [12]. From the perspective of principles and applications of the model, discriminant analysis was based on the discrepancy of distance between output of models and the center of category. Logistic regression responsible for classification of samples was based on regression function values, and the maximum likelihood method was used to estimate the parameters of the equation regression.

Focusing on the background, research was carried out on workload based on HUD to test the subject’s physiological response. To test the sensitivity of the physiological index to workload, a new index, LF/LHF (the ratio between LF and sum of LF and HF), was attempted. And at last, a comprehensive prediction and evaluation method of pilot workload based on the theoretical prediction of pilot workload and the physiological discriminate method was put forward. Our study started with the basic duties and pilot workload element in FAR 25 Appendix D [2], combined with relevant above flight task requirements in the flight manual to conduct a pilot traffic pattern task in flight simulation environment. That was also a basis for TLAP and M-A technology, and used for the prediction of pilot workload. Then, a statistical analysis was conducted to select sensitive physiological indices for mathematical modeling, and a better discriminate result was obtained on multinomial logistic regression model. Our research carried out a preliminary experiment study, which can offer a certain physiological basis for compliance verification of the airworthiness terms relevant to human factor.

Prediction and evaluation method of workload

Prediction of workload

Wickens put forward a multiple resource theory where the visual, verbal, cognitive, and motion dimensions constituted the information processing resource of human beings [14]. When combined with the task timeline analysis method and the MaCrachen-Aldrich scale (M-A scale) evaluation method [13], the multiple resource theory [14] introduced the time effect and task decomposition to typical flight tasks to accomplish the dynamic workload prediction.

Equation (1) calculated the total workload of flight phases. While represents the accumulated workload value, represents the duration of subtask, represents the number of flight operation subtasks, and represents the workload value of flight subtasks calculated by M-A scale which measured based on the expert evaluation method, including visual, verbal, cognition and motion dimensions.

Table 1 shows the subtask duration and M-A scores. For example, take the approach phase with regards to subtask 8, and the M-A scores were 7.1 points (visual: the recognition of altitude on HUD, 3.7 point; verbal: no activity, 0 point; cognition: the next operation to speed controls, 1.2 point; motion: adjust speed controls to 160 knots, 2.2 point). The accumulated workload was , and the cruise and approach phases prediction value were 276.18 and 792.12 respectively, and it should be noted that the predicted workload values were all relative values.

Table 1

Design of flight simulation task and prediction of subtask workload

Phases	No.	Operations	Detailed operations	Concerned instrument (★ represented particularly concerned instrument)	Duration	M-A
Cruise	1	Monitor parameters on HUD	Monitor primary flight parameters on HUD	Altitude, airspeed, pitch angle, roll angle, and heading displayed on HUD	138.09	2
Approach	1	APP mode	Search for position of glide slope indicator on HUD	HUD glide slope indicator, APP switch	3	7.7
	2	Flaps down to 15 degree	(Keyboard Operation in “F7” 3 times), Flaps down	Flap position indicator	2	3.2
	3	Altitude descend to 2000 ft	Observe altitude on HUD	HUD altitude ★, altitude selector	6	5
	4	Flaps down to 35 degree	(Keyboard operation “F7” 2 times), Flaps down	Flap position indicator	2	3.2
	5	Adjust airspeed to 180 knots	MCP panel adjustment (mouse operation)	HUD airspeed ★, speed controls	5	7.1
	6	Set auto-brake switch	Auto-brake switch stage 2 (mouse operation)	Auto brake select switch	2	7.1
	7	Altitude descend to 1500 ft	Observe altitude on HUD	HUD altitude ★, altitude selector	6	5
	8	Adjust airspeed to 160 knots	MCP panel adjustment (mouse operation)	HUD airspeed ★, speed controls	5	7.1
	9	Gear down	(Keyboard operation “G”), confirm landing gear	Landing gear panel ★	3	8.2
	10	Altitude descend to 1000 ft	Observe altitude on HUD	HUD altitude ★, altitude selector	6	5
	11	Adjust airspeed to 140 knots	MCP panel adjustment (mouse operation)	HUD airspeed ★, speed controls	5	7.1
	12	Arm spoilers	(Keyboard operation “shift+/”)	HUD altitude	2	4.2
	13	Cut off autothrotte	MCP panel adjustment (mouse operation)	Command engage switch	2	4.4
	14	Disconnect the auto-pilot	(keyboard operation “Z”)	Command engage switch ★	3	13.4
	15	Monitor parameter on HUD	Instrument monitoring	HUD flight parameters	87.09	2
Landing	1	Descend altitude placidly	(Flying rocker operation)	HUD altitude ★, HUD airspeed ★	22	8.6
	2	Throttle down	(Flying rocker operation)	Engine indication	5	8.6
	3	Prepare to pull up	(Flying rocker operation)	HUD airspeed ★, HUD pitch angle ★	12	18.2
	4	Slow it down	(Flying rocker operation)	Information of airport runway ★	3	12.2
	5	When touched the ground	Decide according to runway	HUD altitude ★	8	11.6
	6	Open the thrust reverser	(Keyboard operation “F2”, flying rocker operation)	Information of airport runway ★	5	10.3
	7	Brake manually	(Keyboard operation “. ”, flying rocker operation)	HUD airspeed ★	5	7.6
	8	Close thrust reverser	(Keyboard release “F2”)	HUD airspeed ★	44.36	2
	9	Monitor parameters on HUD	Instrument monitoring	HUD flight parameters	22	8.6

Evaluation of workload

A further modeling for the three typical flight phases (cruise, approach and landing) was developed. To build up the model with an eye for an uncertain practical category of typical workload and to the greatest extent for the reduction of misjudgment, the multinomial logistic regression theory was selected. The multinomial logistic regression was a natural expansion of regression analysis, which the independent variables don’t have to fulfill the multivariate normal distribution hypothesis. The multinomial logistic regression had the least assumption and the least strict criterion, therefore it can be employed if there is uncertainty of whether all assumptions can be satisfied or whether there is an order of typical workloads [17].

Within a classes multinomial logistic regression model, the logit equations can be express as:

and the final class (class ) was the reference one.

Note , , by means of , , to make a comparison of , , (define 3), and the maximum value was the predicted class.

Materials and methods

Subjects

Fourteen male flying cadets were recruited in our study; two that crashed, one that ran out of the runway (since these subjects were unable to accomplish our experiment, and the data could not be recorded for analysis), and eleven who had valid data. Each cadet had either one or two years of flight simulation experience with in-depth knowledge of flight simulation operations from the Civil Aviation University of China. Their ages ranged from 18–26, with the average age of 20.6. Each of them were right-handed with normal or rectified vision and normal hearing. All subjects were required to refrain from drinking caffeinated or alcoholic beverages, smoking, taking any medication, and strenuous exercise for twelve hours prior to the experiment.

Apparatus

A Tobii TX300 with a 300 HZ sample rate was used to collect eye movement data; a five-point calibration was conducted before the formal test. KingFar International Inc provided a wireless photoelectric pulse sensor with a 64 HZ sample rate which was used to gather the ECG data. Also, a wireless galvanic skin sensor and wireless breathing sensor with a sample rate 64 HZ was provided by the same company. An ErgoLab wireless received all digital radio frequency signals.

Experimental scenario

A vivid HUD flight environment (the primary flight information included airspeed, altitude, pitch, etc.) was included in the HUD display, and a single green color was used for visual coding in a simulated quiet environment for all subjects. The flying rocker, computer keyboard, and computer mouse were used to accomplish a dynamic process of traffic pattern task which included take-off, climbing, cruise, approach, and landing. The flight simulation task was conducted during the summer in Tianjin Binhai international airport, and the aircraft was 737–700 NG. The take-off runway was 16R and the frequency of localizer in instrument landing system was 110.9 MHZ. The left and right fuel tank was set at 25% of total capacity, the center tank was set at 10%, and the other original settings were as follows: park the aircraft on the runway when preparing for takeoff, switch the angle of view to interior 2D visual angle, open no smoking, fasten seat belt switch, turn on taxiing, flag indicator and high frequency flare lights, adjust the magnetic heading to 160, open flight director switch, set the speed hold 220 knots, set heading hold 160, set altitude hold 3000ft, adjust the auto-brake to RTO position and lay down 5 degree flap.

Experimental design

A single factor within-subject design was applied in our experiment, the workload of typical flight phases were the diverse experimental level. Each subject has certain aircraft and HUD display training prior to the experiment. In order to be familiar with the procedures prior to the formal experiment, there was a 30-minute adaptation training. The formal experiment lasts about 20 minutes; all subjects should keep the task instructions to accomplish the experiment. HUD was used more frequently during the approach and landing phases and used less frequently during the take-off and climbing phases (lasted 73.6 s and 73.9 s); it was taken after the cruising altitude was set as 3000 ft. Based on this, a reasonable abstraction has be completed to flight operations, a reasonable abstraction has be completed to flight operations, and three typical flight phases (cruise, approach, and landing), which the mean durations were 138.09 s, 139.09s , and 107.36 s respectively, were selected to conduct an analysis of physiological indices in the dynamic full flight envelope task environment. Table 1 shows the operations of three typical flight phases and concerned instruments, including particularly concerned instruments.

Experimental results and analysis

Eye movement data (fixation frequency, mean fixation time, saccade frequency, mean saccade time, mean blink time, blink rate, and mean pupil diameter), ECG data (mean NN and LF element), and EDA data (mean phasic and mean tonic) were recorded and analyzed for the statistical method. For the analysis of the above data, repetitive measure analysis of variance (ANOVA) was employed. Sphericity is the condition where the variances of the differences between all combinations of related groups (levels) are equal, and the Mauchly’s test was used to test the sphericity of the data [19]. A Greenhouse-Geisser test [20, 21, 22] will be used to correct for the lack of sphericity statistically in the case that the sphericity cannot be fulfilled. The Post-hoc comparison was LSD method while the significance level was 0.05.

Eye movement

An analysis was conducted for the three basic eye movements: fixation, saccade, and blink. A declining trend was shown by the fixation frequency, and an increasing trend was shown by the mean fixation time with the ongoing typical flight task, as shown in Fig. 1a and b, and the CR, AP, LA of x-coordinate stands for cruise, approach and landing phases. As to typical phases of flight, the single-factor repeated measure ANOVA showed fixation frequency has significant main effects of workload ( 28.291, 0.001). Post-hoc comparison showed that the fixation frequency under landing was obviously lower than that under cruise and approach ( 0.05 and 0.05); there were no significant effects between cruise and approach. The single-factor repeated measure ANOVA showed mean fixation time has a significant ( 14.875, 0.001) effect on workload. Post-hoc comparison showed that the mean fixation time under landing was obviously higher than that under cruise and approach ( 0.05 and 0.05); there was no significant effects between cruise and approach.

Figure 1.

Analysis of physiological indices in typical workload.

Figure 1c and d showed the average saccade frequencies and mean saccade times of the subjects under different workloads. The One-way repeated measures ANOVA indicated significant main effect of workload ( 20.354, 0.001) on saccade frequency. Post hoc tests showed that the saccade frequency under landing was obviously lower than those under approach and cruise ( 0.05, 0.05), no significant difference was found between approach and cruise. The main effect of workload on mean saccade time was also significant ( 6.786, 0.006). This effect manifested as that the saccade frequency to task difficulty under landing was obviously higher than those under approach ( 0.05).

With the increase of workload, mean blink time showed a decline trend, while the mean pupil diameter showed an increase trend, as is showed in Fig. 1e and f. One-way repeated measures ANOVA showed that the effect of workload on mean blink time was significant ( 14.186, 0.001). As the workload changed from low, medium, to high, the mean blink times decreased accordingly. Post hoc tests showed significant differences between the mean blink times under approach and landing ( 0.05). Also, the main effect of workload on mean pupil diameter was significant ( 11.311, 0.001). The mean pupil diameter under cruise was obviously lower than under approach ( 0.05) and landing ( 0.05), but no significant difference was found between approach and landing. According to the blink behavior, subjects’ blink rate under cruise, approach and landing were 0.372 0.214, 0.399 0.347, and 0.340 0.444, respectively. The variance analysis indicated that the effect of workload on blink rate was not significant.

ECG indices

Figure 1g and h showed the average values of NN interval – the time domain index of HRV and LF/LHF – the frequency domain index of HRV under different workloads. The main effect of workload on mean NN was significant ( 13.361, 0.001), and mean NN showed a decline trend of variation with the increase of workload. The mean NN under cruise was obviously higher than that under approach ( 0.05) and landing ( 0.05), no significant difference was found between approach and landing. Meanwhile, LF/LHF showed a decline trend with the increase of workload. The variance indicated that the effect of workload on LF/LHF was significant ( 7.2, 0.004), showing that the LF/LHF was higher under cruise than under approach ( 0.05) and landing ( 0.05).The difference between approach and landing failed to reach significance.

EDA

The mean phasic and mean tonic were presented in Fig. 1i and j, and both of them showed an increase trend with the increase of workload. The main effect of workload on mean phasic was significant ( 4.753, 0.040), showing that the mean phasic under cruise was obviously lower than the ones under the other workloads ( 0.05, 0.05). However, the difference between approach and landing was not significant. As for the index of mean tonic, the main effect of workload on it was also significant ( 20.441, 0.001). The mean tonic under the landing phase was significantly higher than that under approach ( 0.05) and cruise ( 0.05). The difference between cruise and approach was also significant ( 0.05).

Validation of workload prediction and correlation analysis between physiological indices

A protocol modeling the average pilot was used to analyze the correlation between the predictions and the measurement indices by Wickens [23, 24], and it was also used in our study for model validation purpose. The predicted value of the three typical flight subtasks (“the adjustment of airspeed”, “disconnected the auto-pilot”, “prepare to pull up”) quantified by workload prediction method, were 7.1, 13.4, and 18.2, respectively. When taking into consideration the differences among operation times of the subjects, a Pearson correlation analysis between predicted values of flight subtask and mean value of physiological indices was carried out to the validation of workload prediction method [24]. Conclusions showed that the predicted values had a highly positive correlation with mean pupil diameter ( 0.941, 0.219), mean skin conductance ( 0.952, 0.197), and mean fixation time ( 0.843, 0.361); They also concluded that the predicted values had a highly negative correlation with fixation frequency (0.931, 0.237), saccade frequency (0.975, 0.142), and mean saccade time (0.917, 0.262), as well as a moderate negative correlation with blink rate (0.781, 0.429). The validation results claimed that the workload prediction method on the prediction of typical flight subtask workload values had favorable prediction efficiency.

A correlation analysis between the mean value of physiological indices and the predicted value during typical workload phase was completed; the results claimed that the physiological indices and predicted value had a high correlation ( 0.8), while the mean saccade time and predicted value had a moderate negative correlation (0.706). Subsequently, a further correlation analysis between predicted value of the dynamic workload phase and physiological data of all subjects was completed, as shown in Table 2. The predicted value was negatively correlated with the fixation frequency (0.664, 0.001), mean fixation time (0.529, 0.002), mean blink time (0.466, 0.006), and LF/LHF (0.558, 0.001) at the significance level of 0.01; results indicated a favorable prediction of workload prediction method.

Table 2

Correlation between predicted MW values and physiological indices

	Fixation	Mean	Saccade	Mean	Mean	pupil	Mean	LF/	Mean	Mean
	frequency/	fixation	frequency/	Saccade	blink	diameter/	NN/	LHF/	phasic/	tonic/
	(N/S)	time/ms	%	time/s	time/%	mm	msec	%	μs	μs
MW
r	-0.664^**	-0.529^**	-0.435^*	-0.319	-0.466^**	-0.276	-0.300	-0.558^**	-0.344	0.391^*
P	< 0.001	0.002	0.011	0.070	0.006	0.120	0.090	0.001	0.050	0.025

Correlation is significant at the 0.05 level (2-tailed); Correlation is significant at the 0.01 level (2-tailed).

The correlation analysis among physiological indices was also completed. At 0.05 significance level, LF/LHF was positively correlated with fixation frequency and mean NN ( 0.366, 0.036; 0.401, 0.021), mean blink time was positive correlated with mean phasic ( 0.420, 0.015). At 0.01 significance level, fixation frequency was negatively correlated with mean fixation time (0.769, 0.001), and positively correlated with saccade frequency, mean saccade time, and mean blink time ( 0.637, 0.001; 0.494, 0.001; 0.609, 0.001). Mean fixation time was negatively correlated with saccade frequency (0.884, 0.001) and mean blink time (0.704, 0.001), saccade frequency was positively correlated with mean blink time ( 0.776, 0.001) and mean NN ( 0.460, 0.007), and mean blink time was also positively correlated with mean NN ( 0.507, 0.001). Mean phasic had a positive correlation with mean tonic (0.500, 0.003), and there was no obvious correlation between the other physiological indices.

The correlation among physiological indices can provide a reference for further selection of pilot physiological indices. According to the analysis results, it can be concluded that the eye movement indices (blink rate excluded) were sensitive to various inflight workloads; the mean NN and LF/LHF of HRV, the tonic and the phasic data of EDA were also sensitive to various typical workload environments. The information concluded in our experiment can provided physiological support for pilot workload evaluation and real flight environment attempts.

Multinomial logistic regression of pilot workload

The analysis of variance confirmed the sensitive physiological indices. A reference indices can be selected for the model when combined with the correlation analysis. The fixation frequency of eye movement, mean NN and LF/LHF of ECG, and mean tonic of EDA were applied for mathematical modeling. The fixation frequency (), mean NN (), LF/LHF (), and mean tonic () were inputted for multinomial logistic regression:

Table 3 shows the classification of prediction results after the computation. There was a regression forecasting to the primitive data; results showed that the correct discrimination of cruise, approach, and landing were 90.91%, 81.82%, 81.82% respectively. The average accuracy was more than 80%, which stated that the model had an ideal effect for workload discrimination.

Table 3

Results of Predicted accuracy

Phases	Predicted number			Accuracy
	Cruise	Approach	Landing
Cruise	10	1	0	90.91%
Approach	1	9	1	81.82%
Landing	0	2	9	81.82%
Percentage	33.33%	36.36%	30.30%	84.85%

Discussion

Due to the application of HUD in our cockpit display environment, the subjects can monitor the flight parameters during the approach and landing phases with a head up status, and certain changes occurred with the behavior of eye movements, which was reflected by the variation of pilot workloads. Fixation frequency was defined as the fixation number divided by fixation time. The vision workload level can be characterized by the fixation frequency to a great extent. In comparison to cruise, the fixation frequency decreased during landing, indicating the enhancement of arousal level. Due to a higher monitoring task, the fixation frequency increased during cruise, also indicating higher visual information and a higher efficiency of information processing [25]. The mean fixation time was defined as the mean fixation duration every single point of fixation behavior. The longer the fixation duration, the deeper the information processing. Among all phases, the landing phase has the longest fixation duration. The fixation duration during landing phase decreased with the augment of saccade operations, which also shows that more saccade operations are needed for the preparation of the final landing.

Saccade frequency is the ratio of saccade number to single total task time. During the approach phase, it is vital to adjust and supervise the altitude and airspeed, while controlling the altitude is vital during the landing phase. The discrepancy that the saccade frequency decreased during landing in comparison with real flight missions can be explained by the lack of landing experience equipped with HUD. Therefore, more research is needed to explore the nature of HUD before promotion. Mean saccade time is the ratio of total saccade time and total saccade number. It described the saccade distance on the HUD display and reflected the difficulty level of visual information acquisition. Mean blink time is the ratio of total blink time and total blink number. It decreased gradually in the typical workload task and was consistent with previous research, which indicated that during visual stimulation tasks, the blink duration decreased as the workload during visual stimulation task increased [26]. At first, the mean saccade time increased and then decreased during the typical workload task. Both mean saccade time and mean blink time was correlated with depth of attention, and a further elaborated workload experiment was needed to observe the accurate variations. Blink rate decreased with the increase of visual processing requirements [27]. It claimed that the blink rate can characterize the workload of information presentation styles to some extent, but there was no significant changes observed during complicated workload operations, this was consistent with the basic theory that no external message was seized during blink behavior. Mean pupil diameter was sensitive to workload, and it increased gradually with the increase of workload. It indicated that a further resource was needed to deal with the increase of workload [28].

The function relationship between NN interval and time was built up by the time domain analysis, and a statistical property was extracted. The contiguous R waveform duration was also called NN interval. During the approach and landing phases, mean NN decreased with the aggravation of tension and activity. During the tracking task, the mean NN of fighter-pilot was greater than that of the counterwork task [9]. The Fourier transform transformed the HRV time domain into HRV frequency signals, and then the HRV frequency band was obtained via power spectral density analysis. The HRV signal was refined as Ultra-Low Frequency (ULF 0–0.0033 HZ), Very Low Frequency (VLF 0.0033–0.04 HZ), Low Frequency (LF 0.04–0.015), and High Frequency (HF 0.15–0.4 HZ) in frequency domain. A large number of studies have shown that the LF ingredient of HRV frequency spectrum can characterize the sympathetic nerve activity; consistent with prior research, during landing LF/LHF significantly decreased with the increase of workload [26].

The original EDA signals can be divided into tonic data and phasic data. Tonic data revealed the galavanic skin level of the task, and the event-related potential in two seconds after a stable stimulation was claimed by phasic data [29]. When a person is in an awake, excited, or nervous state, the sympathetic nerve system will accelerate the skin’s metabolism, increasing the temperature of the skin relevant sweat gland secretion. EDA was sensitive to mental workload, and a fierce EDA response was founded during take-off, go around, and landing in Visual Flight Rules (VFR) [11]. The variation of tonic data and phasic data was triggered by the verbal stimulation and fierce external visual environment in the approach and landing phases. The mean phasic had a better evaluation efficiency in our experiment [29].

A correlation analysis was both used in our work and the research of Liang et al. [13]. They laid emphasis on the validation to subjective indices, while what we focused on were the physiological metrics, both of us achieved acceptable results. The conclusion can be made when the single index was used for modeling, eye response (followed by ECG and EDA) has the best discriminant effect. As for combination of two physiological indices, the combination of eye response and ECG has a better effect than the others, which was consistent with the study of Hogervorst [30]. It is presented that when dealing with vision-related workload, better results were achieved by eye response than any other external measurements (ECG, EDA, and respiration), and EEG combined with eye response has a better result than single EEG and eye response [30]. Table 4 claimed that the combination of two physiological measurements (“eye response and ECG”, “eye response and EDA”, and “ECG and EDA”) was better than the single one, and combining three of them achieved the best results (84.85%) [16]. For the discriminate accuracy, a multinomial logistic regression model was a little lower than the comprehensive Bayes discrimination model (89.58%) indexed by respond time, accuracy, NASA-TLX scores, and SDNN. However, compared to the combination of subjective, performance, and physiological indices, the subjective post analysis was avoided in the multinomial logistic regression model, which might provide certain ideas for online detection. The lack of abundant physiological data in flight was the weakness of this model.

Table 4

Results of predicted accuracy

Physiological indices	Predicted accuracy (%)
	Cruise	Approach	Landing	Mean
Fixation frequency	63.64	45.45	72.73	60.61
Mean NN + LF/LHF	72.73	36.36	63.64	57.58
Mean tonic	63.64	18.18	54.55	45.45
Fixation frequency + mean NN + LF/LHF	81.82	63.64	72.73	72.73
Fixation frequency + mean tonic	63.64	54.55	81.82	66.67
Mean NN + LF/LHF + mean tonic	81.82	36.36	72.73	63.64
Multidimensional	90.91	81.82	81.82	84.85

Conclusion

This research had three different aspects compared to others. At first, the HUD was used as the major visual coding display to test the human errors in our research; the relevant physiological results can be a reference for others. Additionally, a new physiological index-LF/LHF which showed a higher sensitivity to pilot workload was raised and analyzed in the research. Lastly, and most importantly, was the prediction and evaluation method of pilot workload, which included the multiple resource theoretical prediction and multinominal logistic regression model based on combination of physiological indices. Considering the difference between our subject and the real pilot and the difference between the flight simulation environment and real flight circumstances, there were some defects in our work; the experimental results can offer a certain reference and still need more tests in complicated conditions.

Several conclusions can be made based on the result analyzed above:

Based on multiple resource in dynamic flight task and a correlation analysis, a workload prediction has been completed. Predicted by workload prediction method, it claimed that the variation of physiological indices in typical flight subtasks and workload status could be preferable. The results indicated that the comprehensive prediction and evaluation method of workload that the dynamic predict method combined with objective physiological measurement had a favorable effect.

Analysis of variance stated that eye movement, ECG indices, and EDA indices were all sensitive to typical workload. In typical HUD workload status, LF/LHF and fixation frequency were positively correlated; mean phasic and mean blink time were positively correlated; there was also a correlation between fixation, saccade, and blink behavior of eye response; mean NN was positively correlated with saccade frequency and mean blink time; and there mean pupil diameter and other physiological indices has no significant correlation.

The comprehensive model in combination with eye movement, ECG, and EDA had a better discriminate result than the combination of any two or single physiological index. Based on the combination of physiological indices (fixation frequency, mean NN, LF/LHF, and mean tonic), the multinominal logistic regression model had a favorable discriminate accuracy (reaches 84.85%), which can provide a certain reference for pilot workload evaluation.