Meryem Gülce Subaşı1, Gülce Alp2, William M Johnston3, Burak Yilmaz4. 1. Faculty of Dentistry, Department of Prosthodontics Istanbul Aydin University Besyol Mah. Akasya Sok., 34295, Istanbul, Turkey. 2. Faculty of Dentistry, Department of Prosthodontics, Okan University, Akfirat, Tuzla, 34959, Istanbul, Turkey. 3. Division of General Practice and Materials Science, The Ohio State University College of Dentistry, 305 W12th Ave Columbus, OH, 43210, United States. 4. Division of General Practice and Materials Science, The Ohio State University College of Dentistry, 305 W12th Ave Columbus, OH, 43210, United States. Electronic address: yilmaz.16@osu.edu.
Abstract
OBJECTIVE: To compare the effect of material and thickness on the color stability and relative translucency parameters (RTP) for monolithic ceramics subjected to coffee thermocycling. METHODS: Four specimens each at thicknesses of 0.5, 0,7 and 1 mm were sectioned from monolithic ceramics [preshaded monolithic zirconia (MonZr), lithium disilicate (LDS) and zirconia reinforced lithium silicate (ZLS)]. The specimens were glazed and subjected to 5000 coffee thermocycling. The color coordinates of specimens were determined with a spectroradiometer and color differences and RTP values were calculated with CIEDE2000 color difference and TPCIEDE2000 formulas. ANOVA was used to analyze CIEDE2000 color difference and RTP values (α = .05). RESULTS: For the color difference data, the 2-way ANOVA revealed a significant interaction between material and different thickness (P = .002). Except for 0.5 mm thick ZLS material, all materials in all thicknesses studied presented color changes within the clinically acceptable limits after coffee thermocycling. For the RTP data, the 3-way ANOVA revealed a highly significant interaction between material and different thicknesses (P < .001). CONCLUSIONS: Material type and thickness can be expected to affect color change and relative translucency of the restorations made with preshaded MonZr, LDS and ZLS materials. Except for 0.5 mm thick ZLS material, color changes of all studied materials were within the clinically acceptable limits. Except ZLS material, color changes of other materials were not significantly affected by thickness. Staining in coffee was not found to affect translucency, and the materials' translucency parameters were ranked from high to low as LDS, ZLS and MonZr at each thickness studied.
OBJECTIVE: To compare the effect of material and thickness on the color stability and relative translucency parameters (RTP) for monolithic ceramics subjected to coffee thermocycling. METHODS: Four specimens each at thicknesses of 0.5, 0,7 and 1 mm were sectioned from monolithic ceramics [preshaded monolithic zirconia (MonZr), lithium disilicate (LDS) and zirconia reinforced lithium silicate (ZLS)]. The specimens were glazed and subjected to 5000 coffee thermocycling. The color coordinates of specimens were determined with a spectroradiometer and color differences and RTP values were calculated with CIEDE2000 color difference and TPCIEDE2000 formulas. ANOVA was used to analyze CIEDE2000 color difference and RTP values (α = .05). RESULTS: For the color difference data, the 2-way ANOVA revealed a significant interaction between material and different thickness (P = .002). Except for 0.5 mm thick ZLS material, all materials in all thicknesses studied presented color changes within the clinically acceptable limits after coffee thermocycling. For the RTP data, the 3-way ANOVA revealed a highly significant interaction between material and different thicknesses (P < .001). CONCLUSIONS: Material type and thickness can be expected to affect color change and relative translucency of the restorations made with preshaded MonZr, LDS and ZLS materials. Except for 0.5 mm thick ZLS material, color changes of all studied materials were within the clinically acceptable limits. Except ZLS material, color changes of other materials were not significantly affected by thickness. Staining in coffee was not found to affect translucency, and the materials' translucency parameters were ranked from high to low as LDS, ZLS and MonZr at each thickness studied.
Authors: Catarina Gomes; Francisco Martins; José Alexandre Reis; Carlos Pérez Albacete-Martinez; Paulo Durão Maurício Journal: Clin Exp Dent Res Date: 2022-01-09