Design of non-equiatomic medium-entropy alloys.

High-entropy alloys have attracted much attention due to their unique microstructures and excellent properties. Since their invention more than ten years ago, research attention has been mainly focused on the study of multicomponent alloys with equiatomic or near-equiatomic compositions. Here we propose a novel design of non-equiatomic medium-entropy alloys that contain one matrix element and several equiatomic alloying elements. To verify the utility of this new design, a series of Co-free Fex(CrNiAl)100-x (at.%, 25 ≤ x ≤ 65) medium-entropy alloys were designed from the much-studied FeNiCrCoAl high-entropy alloy. Detailed characterization reveals that the alloys exhibit novel two-phase microstructures consisting of B2-ordered nanoprecipitates and BCC-disordered matrix. As the alloys deviate far from equiatomic composition, the structure of the nanoprecipitates transfers from a spinodal-like intertwined structure to a nanoparticle dispersed structure. Previous parametric approaches to predict phase formation rules for high-entropy alloys are unable to describe the phase separation behaviors in the studied alloys. Our findings provide a new route to design medium-entropy alloys and also demonstrate a strategy for designing nanostructured alloys from multicomponent alloy systems through simple variations in non-equiatomic compositions.

Introduction

High-entropy alloys (HEAs) are a newly emerging class of multicomponent alloys that have attracted widespread attention over the past decade[1-6]. Such alloys were initially defined as those containing five or more principal elements in equimolar or near-equimolar ratios, each element with a concentration being between 5 at.% and 35 at.%[1]. Later, another definition of HEAs was also proposed, which suggests that the alloys can be classified as HEAs if their configurational entropies are higher than 1.5 R (R is the gas constant)[3,4]. It can be known from the two definitions that the basic principle behind the design of HEAs is to have high configurational entropy so as to stabilize solid solutions rather than intermetallic compounds. Owing to the high entropy effect, a lot of HEAs can form simple body-centered cubic (BCC) and/or face-centered cubic (FCC) solid solution microstructures[7-12]. Consequently, many HEAs have been found to exhibit excellent properties such as high strength, good wear resistance, outstanding corrosion resistance, and exceptional high and low temperature performance, having a variety of promising applications[13-19].

However, not all HEAs can form a single phase solid solution microstructure. In many cases, the formation of ordered intermetallic phases, complicated compounds or even amorphous phases was often observed[20-23].The formation rules of different phases in HEAs have been widely studied for many years, but the factors controlling phase formation are still under debate[24-29]. In order to optimize the microstructure for desired properties, a common strategy employed until now has been to design multicomponent alloys with equiatomic or near-equiatomic compositions. Recently, some attention has been shifted to the study of multicomponent alloys with non-equiatomic compositions[30-40]. For example, some non-equiatomic multicomponent alloys have been reported, such as Fe42Mn20Ni30Co6Cr2 and Fe40Mn27Ni26Co5Cr2 quinary alloys[37,38], Cr10Mn40Fe40Co10 and Cr4Mn28Fe40Ni28 quaternary alloys[39,40]. The configurational entropies of these alloys at a random state are between 1 R and 1.5 R, which means that they should be classified as medium-entropy alloys (MEAs)[3,4]. Despite of the reduced configurational entropies, these MEAs possess excellent microstructures and properties, which can be compered with or even better than those of HEAs. Not only did this urge us to focus our attention on the class of MEAs, it also triggered us to develop a general approach for designing non-equiatomic MEAs. In the present work, we proposed a novel design of non-equiatomic MEAs that contain one matrix element and several equiatomic alloying elements. In this paper, we firstly expounded the idea and basis of this new alloy design. Then, to verify the utility of this design, we designed a series of Co-free Fe(CrNiAl)100− (at. %, x = 25, 35, 45, 55 and 65) MEAs from the much-studied FeNiCrCoAl HEA. After that, we systematically studied the microstructures of these alloys and also discussed about their phase separation behaviors.

Results

We start expounding our design idea from the classification of the alloy world based on the ranges of configurational entropy (ΔS). The alloy world can be divided into three fields, including low-entropy alloys (LEAs, ΔS < 1 R), medium-entropy alloys (MEAs, 1 R < ΔS < 1.5 R) and high-entropy alloys (HEAs, ΔS > 1.5 R)[3,4]. For the classification, the values of ΔS are calculated at a random state, no matter the alloys are single phase or multiphase at room temperature[3,4]. According to Boltzmann’s hypothesis, for a n-element multicomponent alloy at a random state the ΔS can be calculated by the following equation:where the gas constant R has a value of 8.314 JK−1 mol−1, n is the number of total elements, x is the concentration of element i.

When there is one element with atomic percentage of x and the other elements have equal atomic percentage, equation (1) will be as following:

Based on equation (2), the relationship between ΔS and x of n-element multicomponent alloys can be plotted as shown in Fig. 1. It can be seen that many non-equiatomic multicomponent alloys can be regarded as MEAs since their configurational entropies are between R and 1.5 R. When the multicomponent alloys has one matrix element (x > 0.5), only a little proportion of them are HEAs but quite a few are MEAs. Thus, we can design MEAs not only from equiatomic ternary or quaternary alloy systems, but also from non-equiatomic multicomponent alloys in which there can be one matrix element. For example, we can easily design Fe-based Fe55Mn15Ni15Co15 (1.18 R) quaternary MEA, Fe-based Fe60Mn10Ni10Cr10Co10 (1.23 R) quinary MEA, and Ni-based Ni60Fe8Cr8Co8Cu8Al8 MEA (1.32 R) senary MEA from the existing MEA and HEA systems.

Figure 1

Relationship between ΔS and x of n-element multicomponent alloys with one matrix element (n = 2~10).

To develop a general approach, we advise a new design of non-equiatomic MEAs that contain one matrix element and several equiatomic alloying elements, while also having configurational entropies between 1 R and 1.5 R at a random state. Based on this design, the range of matrix composition can be up to 66 at.%, 71 at.% and 73 at.% for quaternary, quinary and senary systems, respectively. The concentrations of alloying elements are proposed to have equiatomic ratios, such that they may contribute the most to configurational entropies; however, for a more generalised design it is not a must, as long as the alloys still have medium entropies. In this sense, many non-equiatomic multicomponent alloys such as Fe-based Fe55Mn20Cr15Ni5Al5 (1.23 R) and Ni-based Ni57Cr20Co10Al8Mo3Ti2 (1.26 R) can also be regarded as non-equiatomic MEAs. Some conventional alloys containing high concentrations of alloying elements can also be called as non-equiatomic MEAs, such as 316 steel (1.15 R), Inconel 718 superalloy (1.31 R), Stellite 6 superalloy (1.13 R) and Zr53Ti5Cu16Ni10Al16 amorphous alloy (1.30 R)[3,4].

In the design of non-equiatomic MEAs, we may obtain different phases depending on different alloy compositions. This is supposed to be similar with that in HEA systems. Recently, it has been found that the phase formation rules of HEAs are not only determined by configurational entropy, but they are also controlled by many other factors such as mismatch entropy, mixing enthalpy, atomic size difference, valence and electronegativity[24-29]. According to the previous literatures, solid solution phases are stable only when the HEAs have near-zero values of mixing enthalpy and small atomic size difference[25]. If the mixing enthalpy is negative enough to overcome the entropy effect, the formation of intermetallic compounds will occur[27]. With a more negative mixing enthalpy and a larger atomic size difference, the HEAs may be driven to form amorphous phases[26,29]. It is anticipated, therefore, that a proper design of compositions is also required to achieve desired microstructures and properties for non-equiatomic MEAs.

To verify the utility of this new design, we take the design of Fe-Cr-Ni-Al alloys as an example. This alloy system is chosen from the much-studied Fe-Cr-Co-Ni-Al HEA system[8,12,16,22]. The equiatomic FeCrCoNiAl HEA exhibits a two-phase microstructure consisting of BCC-disordered Fe-Cr-rich precipitates and B2-ordered Ni-Al-rich matrix, while the Co element is uniformly distributed in this alloy[22]. In our alloy design, the expensive Co element is omitted considering that the absence of this element may have little influence on the microstructure due to its uniform distribution. Since the Ni-Al-rich intermetallic phase is hard but brittle, a reverse microstructure that contains Ni-Al-rich precipitates dispersed in Fe-Cr-rich matrix should be better for mechanical properties[8]. In order to achieve this, we set Fe as the matrix element and keep the other alloying elements in equimolar ratios. As a result, a series of Co-free Fe(CrNiAl)100− (at. %, x = 25, 35, 45, 55 and 65) alloys were designed, which are denoted as Fe25, Fe35, Fe45, Fe55 and Fe65, respectively. The configurational entropies of these alloys at random state are 1.39 R, 1.36 R, 1.29 R, 1.18 R and 1.03 R, respectively. Therefore, the five alloys can be classified as MEAs since their configurational entropies are between 1 R and 1.5 R. Specifically, the Fe55 and Fe66 MEAs have a matrix element with atomic percentage higher than 50%. In the following, we will systematically study the microstructures of these MEAs as well as their phase separation behaviors.

Figure 2 shows the X-ray diffractometer (XRD) patterns of the as-cast Fe(CrNiAl)100− alloys. In the Fe25 alloy, two different BCC structures were detected. One is disordered BCC structure and the other is ordered BCC (designated as B2) structure. The appearance of (100) superlattice diffraction peak is attributed to the ordered composition distribution in the B2 structure. The other diffraction peaks of BCC and B2 structures overlap, which indicates that they have similar lattice parameters. For the Fe35 alloy, the diffraction intensity of peaks significantly reduces, but several peaks corresponding to BCC structure can still be observed. In the other three alloys including Fe45, Fe55 and Fe65, only (100) diffraction peaks were detected. Such unusual diffraction phenomena is probably attributed to the (100) preferred orientation in their microstructures. From microstructural characterization below, it can be found that these three alloys also contain two different phases. Based on the results of XRD, it can be concluded that although the Fe(CrNiAl)100− alloys have lower and lower mixing entropies when their compositions deviate far from equiatomic compositions, their crystal structures remain quite simple and no complicated compounds appear in these alloys. Hence, the limitation of equiatomic or near-equiatomic compositions in the design of MEAs is not necessary.

Figure 2

XRD patterns of the Fex(CrNiAl)100−x alloys.

The microstructures of the Fe(CrNiAl)100− alloys were characterized by using scanning electron microscopy (SEM). As is seen from Fig. 3a, the Fe25 alloy exhibits a dendritic microstructure at low magnification. At the edge of dendrites, eutectic lamellas can be observed (Fig. 3b). At high magnification, a spinodal-like intertwined nanostructure is found inside the dendrites (Fig. 3c). In the Fe35 alloy, a typical dendritic microstructure can be also observed (Fig. 3d). The interdendrites exhibit a intertwined nanostructure which seems to form by coalescence of nanoparticles and nanowires (Fig. 3e), while the dendrites contain a large number of nanoparticles dispersed in the matrix (Fig. 3f). The average size of the nanoparticles in this alloy is about 400 nm. Compared with the Fe35 alloy, the Fe45 alloy has a similar dendritic microstructure (Fig. 3g), but the proportion of interdendrites in this alloy becomes smaller (Fig. 3h). In the dendrites of the Fe45 alloy, a large number of well-dispersed nanoparticles can also be observed (Fig. 3i), which are about 250 nm in size. In the Fe55 alloy, a equiaxed microstructure containing large grains up to several millimeters in size can be found (Fig. 3j). There are a large number of uniform nanoparticles dispersed inside the grains (Fig. 3k and l). The average size of the nanoparticles in this alloy are about 200 nm. The microstructure of the Fe65 alloy is similar as that of the Fe55 alloy. Large grains about several millimeters in length can be found in this alloy (Fig. 3m). There are also a large number of well-dispersed nanoparticles inside the grains, which are about 100 nm in size (Fig. 3n and o).

Figure 3

SEM secondary electron images of the Fe(CrNiAl)100− alloys. (a)~(c) x = 25, (d)~(f) x = 35, (g)~(i) x = 45, (j)~(l) x = 55, (m)~(o) x = 65.

In order to reveal the chemical compositions of the precipitates and the matrix in the Fe(CrNiAl)100− alloys, the Fe25 and Fe55 alloys were chosen to be analyzed by high-angle annular dark-field (HAADF) detector and energy dispersive spectrometry (EDS) in a transmission electron microscopy (TEM). Fig. 4 presents the HAADF images, EDS maps and EDS line profiles taken in the two alloys. From images as shown in Fig. 4a, it can be seen that the Fe25 alloy exhibits a intertwined nanostructure, in which the Ni-Al-rich phase and the Fe-Cr-rich phase alternate with a period of about 200 nm in the width. In the Fe55 alloy, the nanoparticles are Ni-Al-rich phase while the matrix is the Fe-Cr-rich phase (Fig. 4b). From the EDS line profiles as shown in Fig. 4c, it can be found that quite a few concentrations of Fe are dissolved in the Ni-Al-rich phase, while only a few of Ni and Al elements are dissolved in the Fe-Cr-rich phase. Compared with the Fe25 alloy, there is more concentration of Fe element dissolved in the Ni-Al-rich phase of the Fe55 alloy. The detailed chemical compositions of the Ni-Al-rich phase and the Fe-Cr-rich phase in the two alloys are listed in Table 1.

Figure 4

HAADF images, STEM-EDS maps and compositional profiles of the Fe25(CrNiAl)75 alloy and Fe55(CrNiAl)45 alloy. (a) HAADF image of the Fe25(CrNiAl)75 alloy, (b)~(e) STEM-EDS maps of the Fe25(CrNiAl)75 alloy, (f) HAADF image of the Fe55(CrNiAl)45 alloy, (g)~(j) STEM-EDS maps of the Fe55(CrNiAl)45 alloy, (k) Compositional profiles across the B2 phase of in the Fe25(CrNiAl)75, (l) Compositional profiles across the B2 phase of in the Fe55(CrNiAl)45 alloy.

Table 1

Chemical compositions of phases in Fe25(CrNiAl)75 and Fe55(CrNiAl)45 alloys.

alloy	phase	Fe (at.%)	Cr (at.%)	Ni (at.%)	Al (at.%)
Fe25(CrNiAl)75	Fe-Cr-rich phase	43.31 ± 3.98	49.86 ± 4.57	2.43 ± 0.29	4.40 ± 0.55
	Ni-Al-rich phase	11.03 ± 1.07	2.61 ± 0.31	51.11 ± 4.67	35.25 ± 3.32
Fe55(CrNiAl)45	Fe-Cr-rich phase	70.30 ± 6.42	21.60 ± 1.95	3.70 ± 0.31	4.40 ± 0.57
	Ni-Al-rich phase	19.43 ± 1.83	2.04 ± 0.27	50.40 ± 4.62	28.13 ± 2.70

The structures of the Ni-Al-rich and Fe-Cr-rich phases in the Fe25 and Fe55 alloys were further determined by high-resolution transmission electron microscopy (HRTEM) analysis. Fig. 5a shows the HRTEM image and corresponding inverse Fourier transform (IFF) patterns of the phases in the Fe25 alloy. It can be confirmed that the Ni-Al-rich phase is a B2-ordered phase while the Fe-Cr-rich phase is a BCC-disordered phase. The two phases have coherent lattices. These features are consistent with the result of XRD analysis as shown in Fig. 2. As is seen from Fig. 5b, the Fe55 alloy also has two coherent phases, including Ni-Al-rich B2-ordered phase and Fe-Cr-rich BCC-disordered phase. However, the degree of order of the B2 phases in the alloys is still unable to be determined. According to a previous study, it is speculated that the B2 phases should be partially ordered solid solutions[41].

Figure 5

HRTEM images and FFT patterns of B2 and BCC phases in the Fe25(CrNiAl)75 alloy and Fe55(CrNiAl)45 alloy. (a) HRTEM image of the Fe25(CrNiAl)75 alloy and the corresponding FFT patterns of B2 and BCC phases in the insets, (b) HRTEM image of the Fe55(CrNiAl)45 alloy and the corresponding FFT patterns of B2 and BCC phases in the insets.

From the above results, it can be concluded that the Fe(CrNiAl)100− alloys exhibit novel two-phase microstructures consisting of Ni-Al-rich B2-ordered nanoprecipitates embed in coherent Fe-Cr-rich BCC-disordered matrix. As the x increases, the structure of the B2 nanoprecipitates can transfer from a spinodal-like intertwined structure to a nanoparticle dispersed structure. Specifically, the Fe55(CrNiAl)45 and Fe65(CrNiAl)35 alloys contain a large density of highly dispersed nanoparticles in the matrix. These results provide an experimental evidence that non-equiatomic MEAs with one matrix element can form excellent microstructures.

Discussion

The non-equiatomic MEA design we proposed breakthroughs the limitation of the existing HEA design, in which no matrix element is supposed to be used. As a result, a large number of new non-equiatomic MEAs can be obtained. For HEAs it is understood that the highest entropy will result in the lowest Gibbs free energy and thus, the highest phase stability. Then, what are the significances of MEA design? In our opinion, some MEAs with properly designed compositions may still have high phase stability, though they have reduced mixing entropies. For instance, the reported CrCoNi, FeNiCrCo and Fe42Mn20Ni30Co6Cr2 MEAs are all single-phase solid solutions, owing to their near-zero values of mixing enthalpy and small atomic size difference[37,42,43]. On the other hand, many MEAs may separate into multiple phases due to reduced phase stability resulting from reduced entropies, but they may benefit from the obtained multiple-phase structures. For example, compared with the most widely studied single-phase FeMnNiCoCr HEA, the dual-phase Fe50Mn30Co10Cr10 MEA can have better mechanical properties due to interface hardening and transformation hardening[40]. In comparison with the much-studied dual-phase FeNiCrCoAl HEA, the triple-phase Fe33.3Ni33.3Cr16.7Al16.7 MEA can exhibit better mechanical properties due to its composite effect of soft and hard phases[44]. It is believed that a number of MEAs with multiple-phase structures and excellent properties can be designed based on existing MEA and HEA systems. Moreover, for multicomponent alloys systems containing multiple phases, a proper non-equiatomic MEA design can be applied to optimize the size, morphology and distribution of phases for desired properties. The expensive elements can also be replaced by cost effective ones if possible in non-equiatomic MEA design, which will reduce the cost of alloys and facilitate their application. Therefore, in the future development of multicomponent alloys, the study of non-equiatomic MEAs is worth pursuing.

In order to interpret the phase separation behaviors in the Fe(CrNiAl)100− alloys, we firstly analyze the interaction among the constituent elements in these alloys. Table 2 presents the physiochemical properties of the Fe, Cr, Ni and Al elements and the mixing enthalpies of binary systems containing these elements[29,45]. It can be seen that the mixing enthalpy of Ni-Al, Fe-Al and Cr-Al is −22 kJ/mol, −11 kJ/mol and −10 kJ/mol, respectively. Thus, they are all likely to form a B2 ordered phase[46,47]. However, the Ni and Al elements have the most negative mixing enthalpy as well as the largest difference of Pauling electronegativity. Therefore, they are most thermodynamically favored to form the Ni-Al-rich B2 phase. Since the Fe and Al elements also have large difference of Pauling electronegativity and large negative mixing enthalpy, the Fe element is thermodynamically favored to dissolve in the B2 phase. For the Cr element, although it also has quite large negative mixing enthalpy with Al, the difference of Pauling electronegativity between Cr and Al is the smallest. Hence, only a few concentration of Cr is dissolved in the B2 phase and most of Cr stays in the matrix, forming the BCC phase. Such separation behaviors of Fe-Cr-rich phase and Ni-Al-rich phase were also observed in the Fe-Cr-Co-Ni-Al HEA system[12,22] and Fe-Cr-Co-Cu-Ni-Al HEA system[10,21].

Table 2

Physiochemical properties of Fe, Cr, Ni and Al elements and mixing enthalpies of binary systems containing these elements calculated by Miedema’s model[45].

Element		Fe	Cr	Ni	Al
Radius/Å		1.241	1.249	1.246	1.432
Pauling electronegativity		1.83	1.66	1.91	1.432
Valence electron concentration		8	6	10	3
Tm (K)		1808	2130	1726	933
Mixing enthalpies (kJ/mol)	Fe		−1	−2	−11
	Cr			−7	−10
	Ni				−22

The phase formation rules of HEAs have been widely studied through many parametric approaches, such as atomic size difference δ, mixing enthalpy ΔH, mixing entropy ΔS, valence electron concentration VEC and parameter Ω[25-29]. It has been demonstrated that, when δ ≤ 6.6% and Ω ≥ 1.1, the alloy can form simple solid solution phases[25]. Moreover, it was proposed that the stability of BCC and FCC phases can be predicted based on the values of VEC[28]. The FCC phase is stable if VEC ≥ 8, while the BCC phase is stable if VEC ≤ 6.87. When the value of VEC is between 6.87 and 8, a mixture microstructure containing both FCC and BCC phases is favored. For the Fe(CrNiAl)100− alloys, the corresponding values of δ, ΔH, TmΔS, Ω and VEC were calculated based on the expressions from reported studies[25,28]. As seen from Table 3, the values of VEC for the Fe(CrNiAl)100− alloys are between 6.75 and 7.42. However, only BCC and B2 phases have been found in these alloys but no FCC phase exist. Thus, the formation of phases in the Fe(CrNiAl)100− alloys can not be predicted by the existing VEC rules. In the studied alloys, the values of δ vary from 6.26% to 4.81% while the values of Ω are between 1.43 and 2.34. As predicted by the criteria of Ω > 1.1 and δ < 6.6% in HEAs, the alloys should form solid solution phases. However, these alloys form both BCC disordered phase and B2 ordered intermetallic phase. Hence, more exquisite criteria are needed to describe the separation of BCC and B2 phases.

Table 3

Parameters of ΔH, TΔS, Ω, δ, and VEC calculated for the Fe(CrNiAl)100− alloys.

Fex(CrNiAl)100−x	ΔHmix(kJ/mol)	TmΔSmix(kJ/mol)	Ω	δ × 100	VEC
x = 25	−13.25	19.00	1.43	6.26	6.75
x = 35	−11.57	18.91	1.63	6.01	6.92
x = 45	−9.86	18.18	1.84	5.70	7.08
x = 55	−8.13	16.84	2.07	5.30	7.25
x = 65	−6.37	14.88	2.34	4.81	7.42

The size, shape and distribution of Ni-Al-rich precipitates in the Fe(CrNiAl)100− alloys have a close relationship with the concentration of Ni and Al elements. A high concentration of Ni and Al elements in the Fe25 alloy leads to the formation of a spinodal-like intertwined structure. At low concentrations of Ni and Al elements such as in Fe55 and Fe65 alloys, highly dispersed nanoparticle precipitates can be obtained. This provides a new approach to control phase separation in similar multicomponent alloys through simple variations in non-equiatomic compositions. The detailed formation processes of the Ni-Al-rich precipitates in the Fe(CrNiAl)100− alloys are still unclear, which will be studied in the future.

In summary, here we propose a novel design of non-equiatomic medium-entropy alloys. Specifically, such alloys may contain one matrix element and several equiatomic alloying elements, while also having configurational entropies between 1 R and 1.5 R. Based on this new strategy, we successfully designed a series of Co-free Fe(CrNiAl)100− medium-entropy alloys from the much-studied FeCrCoNiAl high-entropy alloy. The alloys exhibit novel two-phase microstructures consisting of Ni-Al-rich B2-ordered nanoprecipitates embed in Fe-Cr-rich BCC-disordered matrix. With the increase of x, the structure of the nanoprecipitates transfer from a spinodal-like intertwined structure to a nanoparticle dispersed structure. These phase separation behaviors can not be predicted by previous parametric approaches. Our findings provide a new route to design medium-entropy alloys and also demonstrate a possibility for designing nanostructured alloys in similar multicomponent alloy systems through simple variations in non-equiatomic compositions.

Methods

In the processing of the Fe(CrNiAl)100− alloys, the ingots were prepared by vacuum arc-melting under argon protection. The purity of raw Fe, Cr, Ni and Al metals is higher than 99.9 wt.%. All ingots were melted with electromagnetic stirring five times in order to homogenize their chemical compositions, and then the ingots were cooled naturally in the furnace. The crystal structures of the alloys were identified by an X-ray diffractometer (D/max-rb) with Cu radiation target. The scan range 2θ is from 20° to 100° using a scanning step size of 0.026°. The microstructures of the alloys were characterized by a scanning electron microscopy (Quanta 200FEG). The chemical compositions of phases in the alloys were analyzed by a transmission electron microscopy (Talos F200x) using an high-angle annular dark-field detector and an energy dispersive spectrometry (EDS).