Lisa Bodden1, Nina Lümkemann2, Valerie Köhler3, Marlis Eichberger2, Bogna Stawarczyk4. 1. Department of Prosthetic Dentistry, University Hospital, Ludwig-Maximilians-University Munich, Goethestraße 70, 80336 Munich, Germany; Institute of Medical and Polymer Engineering, Technical University Munich, Boltzmannstraße 15, 85748 Garching, Germany. 2. Department of Prosthetic Dentistry, University Hospital, Ludwig-Maximilians-University Munich, Goethestraße 70, 80336 Munich, Germany. 3. Institute of Medical and Polymer Engineering, Technical University Munich, Boltzmannstraße 15, 85748 Garching, Germany. 4. Department of Prosthetic Dentistry, University Hospital, Ludwig-Maximilians-University Munich, Goethestraße 70, 80336 Munich, Germany. Electronic address: bogna.stawarczyk@med.uni-muenchen.de.
Abstract
OBJECTIVE: The aim of this study was to investigate the impact of a heating/quenching process on the optical, mechanical and thermodynamic properties of filled (20%_4000) and unfilled PEEK films (0%_2000 and 0%_4000). Heating/quenching was performed to simulate thermoforming as possible method to process thermoplastic polymers for dental application. METHODS: For the investigation, films of different PEEK qualities (0%_2000, 0%_4000, 20%_4000) were produced using isostatic pressing (n=10/quality). From each PEEK film, round specimens (n=20/PEEK film) with a diameter of 34mm were cut and following parameters were determined: translucency (T%), Martens-Hardness (HM), indentation modulus (EIT), glass transition temperature (TG), melting temperature (TM) and enthalpy of fusion (ΔHf). Same specimens were exposed to heating/quenching using defined parameters. Afterwards, T%, HM, EIT, TG, TM and ΔHf were determined again. Data were analysed using Kolmogorov-Smirnov test, univariate ANOVA followed by post-hoc Scheffé test with partial eta squared (ηp2), Kruskal-Wallis and Mann Whitney U test. Level of significance was defined to 95%. RESULTS: Materials showed significant differences for all investigated parameters in the initial state, except of TG (p=0.249). The heating/quenching process showed a significant increase on T% for the unfilled materials 0%_2000 and 0%_4000. HM and EIT decreased significantly through heating/quenching for all materials. Moreover, heating/quenching showed a reduction of TG for 0%_2000 and 20%_4000, while TM decreased for 0%_2000 and 0%_4000. ΔHf confirms different crystallinities of tested materials. SIGNIFICANCE: The heating/quenching process showed a significant impact on all investigated parameters. The highest impact was found for mechanical properties resulting in decreased values of HM and EIT.
OBJECTIVE: The aim of this study was to investigate the impact of a heating/quenching process on the optical, mechanical and thermodynamic properties of filled (20%_4000) and unfilled PEEK films (0%_2000 and 0%_4000). Heating/quenching was performed to simulate thermoforming as possible method to process thermoplastic polymers for dental application. METHODS: For the investigation, films of different PEEK qualities (0%_2000, 0%_4000, 20%_4000) were produced using isostatic pressing (n=10/quality). From each PEEK film, round specimens (n=20/PEEK film) with a diameter of 34mm were cut and following parameters were determined: translucency (T%), Martens-Hardness (HM), indentation modulus (EIT), glass transition temperature (TG), melting temperature (TM) and enthalpy of fusion (ΔHf). Same specimens were exposed to heating/quenching using defined parameters. Afterwards, T%, HM, EIT, TG, TM and ΔHf were determined again. Data were analysed using Kolmogorov-Smirnov test, univariate ANOVA followed by post-hoc Scheffé test with partial eta squared (ηp2), Kruskal-Wallis and Mann Whitney U test. Level of significance was defined to 95%. RESULTS: Materials showed significant differences for all investigated parameters in the initial state, except of TG (p=0.249). The heating/quenching process showed a significant increase on T% for the unfilled materials 0%_2000 and 0%_4000. HM and EIT decreased significantly through heating/quenching for all materials. Moreover, heating/quenching showed a reduction of TG for 0%_2000 and 20%_4000, while TM decreased for 0%_2000 and 0%_4000. ΔHf confirms different crystallinities of tested materials. SIGNIFICANCE: The heating/quenching process showed a significant impact on all investigated parameters. The highest impact was found for mechanical properties resulting in decreased values of HM and EIT.