Ediléia Lodi1, Kátia R Weber1, Paula Benetti2, Pedro H Corazza2, Álvaro Della Bona3, Márcia Borba4. 1. Doctoral student, Post-Graduate Program in Dentistry, Dental School, University of Passo Fundo, Rio Grande do Sul, Brazil. 2. Professor of Prosthodontics, Post-Graduate Program in Dentistry, Dental School, University of Passo Fundo, Rio Grande do Sul, Brazil. 3. Senior Professor in Biomaterials, Post-Graduate Program in Dentistry, Interim Dean, Dental School, University of Passo Fundo, Rio Grande do Sul, Brazil. 4. Professor of Dental Materials, Post-Graduate Program in Dentistry, Dental School, University of Passo Fundo, Rio Grande do Sul, Brazil. Electronic address: marciaborba@upf.br.
Abstract
STATEMENT OF PROBLEM: Investigating the mechanical behavior of ceramics in a clinically simulated scenario contributes to the development of new and tougher materials, improving the clinical performance of restorations. The optimal in vitro environment for testing is unclear. PURPOSE: The purpose of this in vitro study was to investigate the failure behavior of a leucite-reinforced glass-ceramic under compression loading and fatigue in different simulated oral environment conditions. MATERIAL AND METHODS: Fifty-three plate-shaped ceramic specimens were produced from computer-aided design and computer-aided manufactured (CAD-CAM) blocks and adhesively cemented onto a dentin analog substrate. For the monotonic test (n=23), a gradual compressive load (0.5 mm/min) was applied to the center of the specimens, immersed in 37ºC water, using a universal testing machine. The initial crack was detected with an acoustic system. The fatigue test was performed in a mechanical cycling machine (37ºC water, 2 Hz) using the boundary technique (n=30). Two lifetimes were evaluated (1×106 and 2×106 cycles). Failure analysis was performed using transillumination. Weibull distribution was used to evaluate compressive load data. A cumulative damage model with an inverse power law (IPL) lifetime-stress relationship was used to fit the fatigue data. RESULTS: A characteristic failure load of 1615 N and a Weibull modulus of 5 were obtained with the monotonic test. The estimated probability of failure (Pf) for 1×106 cycles at 100 N was 31%, at 150 N it was 55%, and at 200 N it was 75%. For 2×106 cycles, the Pf increased approximately 20% in comparison with the values predicted for 1×106 cycles, which was not significant. The most frequent failure mode was a radial crack from the intaglio surface. For fatigue, combined failure modes were also found (radial crack combined with cone crack or chipping). CONCLUSIONS: Fatigue affects the fracture load and failure mode of leucite-reinforced glass-ceramic.
STATEMENT OF PROBLEM: Investigating the mechanical behavior of ceramics in a clinically simulated scenario contributes to the development of new and tougher materials, improving the clinical performance of restorations. The optimal in vitro environment for testing is unclear. PURPOSE: The purpose of this in vitro study was to investigate the failure behavior of a leucite-reinforced glass-ceramic under compression loading and fatigue in different simulated oral environment conditions. MATERIAL AND METHODS: Fifty-three plate-shaped ceramic specimens were produced from computer-aided design and computer-aided manufactured (CAD-CAM) blocks and adhesively cemented onto a dentin analog substrate. For the monotonic test (n=23), a gradual compressive load (0.5 mm/min) was applied to the center of the specimens, immersed in 37ºC water, using a universal testing machine. The initial crack was detected with an acoustic system. The fatigue test was performed in a mechanical cycling machine (37ºC water, 2 Hz) using the boundary technique (n=30). Two lifetimes were evaluated (1×106 and 2×106 cycles). Failure analysis was performed using transillumination. Weibull distribution was used to evaluate compressive load data. A cumulative damage model with an inverse power law (IPL) lifetime-stress relationship was used to fit the fatigue data. RESULTS: A characteristic failure load of 1615 N and a Weibull modulus of 5 were obtained with the monotonic test. The estimated probability of failure (Pf) for 1×106 cycles at 100 N was 31%, at 150 N it was 55%, and at 200 N it was 75%. For 2×106 cycles, the Pf increased approximately 20% in comparison with the values predicted for 1×106 cycles, which was not significant. The most frequent failure mode was a radial crack from the intaglio surface. For fatigue, combined failure modes were also found (radial crack combined with cone crack or chipping). CONCLUSIONS:Fatigue affects the fracture load and failure mode of leucite-reinforced glass-ceramic.
Authors: Katia R Weber; Daniel E Meneghetti; Paula Benetti; Alvaro Della Bona; Jason A Griggs; Márcia Borba Journal: J Prosthet Dent Date: 2021-09-02 Impact factor: 3.426