Literature DB >> 28434832

Conventional Versus Computer-Assisted Corrective Osteotomy of the Forearm: a Retrospective Analysis of 56 Consecutive Cases.

David Ephraim Bauer1, Stefan Zimmermann2, Alexander Aichmair2, Andreas Hingsammer2, Andreas Schweizer2, Ladislav Nagy2, Philipp Fürnstahl3.   

Abstract

PURPOSE: Accuracy and feasibility of corrective osteotomies using 3-dimensional planning tools and patient-specific instrumentation has been reported by multiple authors with promising results. However, studies describing clinical outcomes following these procedures are rare. Therefore, the purpose of this study was to compare the results of computer-assisted corrective osteotomies of the diaphyseal and distal radius with a conventional non-computer-assisted technique regarding duration of surgery, consolidation of the osteotomy, and complications. Also, subjective and objective clinical outcome parameters were assessed.
METHODS: We retrospectively compared the results of 31 patients who underwent a corrective osteotomy performed conventionally with 25 patients treated with a computer-assisted method (CA) using patient-specific instrumentation. Baseline data were similar among both groups. The duration of surgery, bony consolidation, complications, gain in range of motion, and subjective outcome were recorded.
RESULTS: The mean operating time was significantly shorter in the CA group compared with the conventional group. After 12 weeks, significantly more osteotomies were considered healed in the CA group compared with the conventional group. Two patients in the CA group required revision surgery to treat nonunion of the osteotomy. Otherwise clinical results were similar among both groups.
CONCLUSIONS: The results demonstrate that the computer-assisted method facilitates shorter operation times while providing similar clinical results. TYPE OF STUDY/LEVEL OF EVIDENCE: Therapeutic IV.
Copyright © 2017 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

Entities:  

Keywords:  Malunion; distal radius; patient specific instrumentation; rapid prototyping

Mesh:

Year:  2017        PMID: 28434832     DOI: 10.1016/j.jhsa.2017.03.024

Source DB:  PubMed          Journal:  J Hand Surg Am        ISSN: 0363-5023            Impact factor:   2.230


  5 in total

1.  Early Correction of Distal Radius Partial Articular Malunion Leads to Good Long-term Functional Recovery at Mean Follow-up of 4 Years.

Authors:  T David Luo; Fiesky A Nunez; Elizabeth A Newman; Fiesky A Nunez
Journal:  Hand (N Y)       Date:  2018-08-10

2.  Patient-specific plate for navigation and fixation of the distal radius: a case series.

Authors:  Johannes G G Dobbe; Abbas Peymani; Hendrika A L Roos; Maikel Beerens; Geert J Streekstra; Simon D Strackee
Journal:  Int J Comput Assist Radiol Surg       Date:  2021-02-11       Impact factor: 2.924

3.  Computer-assisted correction of incongruent distal radioulnar joints in patients with symptomatic ulnar-minus variance.

Authors:  Lea Estermann; Lukas Urbanschitz; Lisa Reissner; Andreas Schweizer
Journal:  J Hand Surg Eur Vol       Date:  2022-06-14

4.  Three-Dimensional Planning and Patient-Specific Instrumentation for the Fixation of Distal Radius Fractures.

Authors:  Tatjana Pastor; Ladislav Nagy; Philipp Fürnstahl; Simon Roner; Torsten Pastor; Andreas Schweizer
Journal:  Medicina (Kaunas)       Date:  2022-05-30       Impact factor: 2.948

5.  Patient-Specific Three-Dimensional-printed Instrumentation for Radius Lengthening Osteotomy by a Volar Approach in Epiphysiodesis Sequelae: A Case Report.

Authors:  Marc-Olivier Gauci; Mikael Chelli; Jonathan Fernandez; Nicolas Bronsard
Journal:  J Orthop Case Rep       Date:  2020
  5 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.