The Use of Spray-Dried Mn₃O₄/C Composites as Electrocatalysts for Li-O₂ Batteries.

The electrocatalytic activities of Mn₃O₄/C composites are studied in lithium-oxygen (Li-O₂) batteries as cathode catalysts. The Mn₃O₄/C composites are fabricated using ultrasonic spray pyrolysis (USP) with organic surfactants as the carbon sources. The physical and electrochemical performance of the composites is characterized by X-ray diffraction, scanning electron microscopy, particle size analysis, Brunauer-Emmett-Teller (BET) measurements, elemental analysis, galvanostatic charge-discharge methods and rotating ring-disk electrode (RRDE) measurements. The electrochemical tests demonstrate that the Mn₃O₄/C composite that is prepared using Trition X-114 (TX114) surfactant has higher activity as a bi-functional catalyst and delivers better oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalytic performance in Li-O₂ batteries because there is a larger surface area and particles are homogeneous with a meso/macro porous structure. The rate constant (kf) for the production of superoxide radical (O₂•-) and the propylene carbonate (PC)-electrolyte decomposition rate constant (k) for M₃O₄/C and Super P electrodes are measured using RRDE experiments and analysis in the 0.1 M tetrabutylammonium hexafluorophosphate (TBAPF₆)/PC electrolyte. The results show that TX114 has higher electrocatalytic activity for the first step of ORR to generate O₂•- and produces a faster PC-electrolyte decomposition rate.

1. Introduction

Rechclass="Chemical">argeable <class="Chemical">span class="Chemical">lithium–oxygen (Li–O2) batteries are very efficient energy-storage devices and are used as power sources for electric vehicles (EV) and hybrid electric vehicles (HEV) because of their low cost, environmentally benign effects and high theoretical energy density (~3500 Wh·kg−1), which is almost nine times higher than that of current Li-ion batteries (~400 Wh·kg−1) [1,2,3,4]. Despite these favorable characteristics, their practical applications have still been hampered in the past decade because of their limited rate capability, poor cycling stability due to the instability of the electrode and electrolyte, and low round-trip efficiency induced by excessive polarization, resulting in a wide charge–discharge voltage gap [1,2,3,4,5,6,7,8]. These critical problems are predominantly caused by the O2 cathode.

Many studies [1,4,7,8,9,10,11] have shown that the electrochemical performance of Li–class="Chemical">O2 batteries depends on many factors, such as the nature and microstructure of the <class="Chemical">span class="Chemical">O2 electrode, the formulation of the electrolyte (especially, the composition of the solvent), the possible presence of reactive contaminants (e.g., trace water) and the choice of catalysts. In order to enhance the properties of rechargeable Li–O2 batteries, most studies have focused on the electrolyte formula, choice, and microstructure design of the O2 electrode/electrocatalyst, and optimization of the operating parameters [1,3,8]. Because there is poor electrochemical reversibility on the oxygen cathode side, a cathode catalyst that is highly active and has good chemical stability is necessary for good battery performance [5,12]. Therefore, a bi-functional cathode catalyst that facilitates the complete reversibility of oxygen reduction reactions (ORRs) and oxygen evolution reactions (OERs) at low polarization in Li–O2 batteries is required. Several potential electrocatalysts that promote ORRs and OERs in Li–O2 batteries have recently been proposed, including nitrogen-doped carbon, metal oxides, metal nitrides, precious and nonprecious metals, etc. [1,2,6,11,13,14,15,16,17]. Among metal oxides, manganese oxide is a catalyst material of great interest owing to its low cost, environmental friendliness, abundance, and electrocatalytic activity for ORRs in Li–O2 batteries [1,6,16,18]. Carbon-supported manganese oxide (MnO, Mn3O4, MnOOH et al.), which combine the good catalytic performance of manganese oxide with the optimized morphology and size of carbon materials, is a preferred electrocatalyst for ORRs and OERs in Li–O2 batteries [1,19,20,21]. Therefore, this study of Li–O2 batteries focuses on Mn3O4/C catalysts.

Ultrasonic spray pyrolysis (USP) is eminently suitable for the fabrication of heat-treated solid-state materials because the manufacturing process is a one-step process and produces spherical and uniform pclass="Chemical">articles with a p<class="Chemical">span class="Chemical">article size that can be controlled. This study uses the USP method to prepare homogeneous spherical Mn3O4/C particles and uses various organic surfactants, such as Trition® X-114 (TX114), Pluronic® F-127 (F127) and Pluronic® P-123 (P123), as structure-directing agents and residual carbon sources. The aim of this work is to develop a new heat-treatment method for the synthesis of high-surface-area Mn3O4/C catalysts and demonstrate the significant effect of morphology on the electrocatalytic performance of cathode catalysts for Li–O2 batteries. We present a detailed study of the Li–O2 electrochemistry of the Mn3O4/C material, using an electrolyte of 1 M LiPF6 in a propylene carbonate (PC) solvent. The PC solvent is used because it was used in many of the initial studies on Li–O2 batteries, in spite of its poor stability. Although there have been many studies of the use of Mn3O4/C materials in Li–O2 batteries, few studies have examined the poor stability of the electrolyte because of its reaction with the superoxide radical (O2•−) that is produced upon the discharge at the Mn3O4/C electrode. Therefore, as the reported in our early study [6], aspects of the PC-based electrolyte reaction against O2•− and the related kinetic information of O2•− in the Mn3O4/C electrode are explored by studying rotating ring-disk electrode (RRDE) experiments and using a lithium-free non aqueous electrolyte because of the stability of the intermediate O2•−. The O2 solubility, diffusion rates of O2 and superoxide radical (O2•−) coefficients ( and ), rate constant (k) for the production of O2•− and PC-electrolyte decomposition rate constant (k) of the as-prepared Mn3O4/C electrode are measured.

2. Experimental Methods

class="Chemical">Mn3O4/C composites were prep<class="Chemical">span class="Chemical">ared using ultrasonic spray pyrolysis (USP) with manganese sulfate as the manganese ion precursors and organic surfactants as the structure-directing agents and carbon sources. The schematic diagram for the USP experimental apparatus is given in Figure 1. A humidifier ultrasonically nebulizes a precursor solution to form micrometer-size aerosol droplets. The aerosol droplets are then carried by Ar gas into a furnace, where the droplets evaporate and the precursor decomposes. The final solid products were collected by filtration. A precursor solution was prepared by dissolving 90 wt % manganese sulfate monohydrate (MnSO4·H2O, Sigma Aldrich, St. Louis, MO, USA) and 10 wt % organic surfactants into deionized water, to achieve a 0.5 M concentration of MnSO4. Three different organic surfactants were used: TX 114 (Trition® X-114, Sigma Aldrich, St. Louis, MO, USA), F127 (Pluronic® F-127, Sigma Aldrich, St. Louis, MO, USA) and P123 (Pluronic® P-123, Sigma Aldrich, St. Louis, MO, USA). The homogeneous precursor solution was obtained by ultrasonic treatment and was converted into an aerosol using a 2.4 MHz ultrasonic nebulizer (Model WB-P2424FX, Whirl Best, Taoyuan City, Taiwan), which produces small droplets. The aerosol droplets were carried into a heated quartz tube (diameter: 25 mm, length: 30 cm) by a continuous high-purity Ar flow (500 mL·min−1) for sulfate pyrolysis and microsphere solidification. The quartz tube was installed inside a split-hinge tube furnace, which was maintained at 800 °C. The solid particles that formed were collected in a vacuum filter at the other end of quartz tube. The final microsphere Mn3O4/C composites were isolated on 450 nm filter paper, washed sequentially with absolute ethanol and purified water several times, and dried at 110 °C for 6 h.

Figure 1

A schematic diagram of the experimental apparatus for ultrasonic spray pyrolysis (USP).

A Rigaku-D/MaX-2550 diffractometer (Rigaku, Tokyo, Japan) with Cu Kα radiation (λ = 1.54 Å) was used to obtain X-ray diffraction (XRD) patterns for the samples. The morphology of the sample was observed using a scanning electron microscope (SEM, Hitachi S-3400 Hitachi Limited, Tokyo, Japan). The Brunauer-Emmett-Teller (BET) method was used to measure the specific surface class="Chemical">area of the powders (ASAP2020). P<class="Chemical">span class="Chemical">article size analysis (PSA) used a Malvern particle size analyzer (Zetasizer Nano ZS, Malvern Instruments Ltd, Malvern, UK). The residual carbon content of the samples was determined using an automatic elemental analyzer (EA, Elementar vario EL III Elementar Analysensysteme GmbH, Hanau, Germany).

For electrochemical tests, the class="Chemical">Mn3O4/C electrodes were prep<class="Chemical">span class="Chemical">ared by wet coating. They were made from as-prepared Mn3O4/C composites with super P and a poly(vinylidene difluoride) (PVDF) binder (MKB-212C, Elf Atochem, Atofina, Serquigny, France) in a weight ratio of 64:16:20. The Mn3O4/C composites and super P were first added to a solution of PVDF in N-methyl-2-pyrrolidone (NMP, Riedel-deHaen, Seelze, Germany). The mixture was stirred for 20 min at room temperature using a magnetic stir bar, and then for 5 min using a turbine at 2000 rpm in order to produce a slurry with an appropriate viscosity. The resulting slurry was coated onto a piece of separator (Celgard 2400, Charlotte, NC, USA) and dried at 60 °C under vacuum for 12 h. The coating had a thickness of ~100 μm with an active material mass loading of 8 ± 1 mg·cm−2. The quantity of active materials on the electrodes was kept constant. The electrodes were dried overnight at 60 °C under vacuum, before being transferred into an argon-filled glove box for cell assembly. The Li–O2 test cell (EQ-STC-LI-AIR, MTI Corporation, Richmond, CA, USA) was constructed using lithium metal as the negative electrode and the Mn3O4/C electrode as the positive electrode. A solution of 1 M LiPF6 in a PC solvent was used as the electrolyte for all cells. After assembly, the test cell was removed from the Ar-filled glove box and attached to a gas manifold that was constantly purged with dry O2. The electrochemical tests were performed after the cell has been flushed with O2 for 6 h. The cells were galvanoststically cycled using a BAT-750B (Acu Tech System, Taipei, Taiwan) at a constant current of 0.2 mA·cm−2 with a voltage of 2.0–4.5 V vs. Li/Li+ at room temperature.

For class="Chemical">RRDE experiments, an <class="Chemical">span class="Chemical">RRDE system (AFMT134DCPTT, Pine Research Instruments, Durham, NC, USA) with interchangeable disks consists of a 5 mm diameter glassy carbon electrode and a Pt ring electrode (1 mm width) with a 0.5 mm gap between them. The collection efficiency for this geometry is 0.24. The rotating ring-disk assembly was operated on a Pine AFMSRX rotator and CH705 Bipotentiostat (CH Instruments, Austin, TX, USA) with a computerized interface. Experiments were conducted using a three-electrode cell containing 10 mL of the electrolyte of interest. The cell was assembled in a dry Ar-filled atoms bag (Sigma-Aldrich Z108450, ST. Louis, MO, USA). The counter electrode was a Li foil that was connected to an Ag wire and isolated by a layer of Celgard 2400 separator to prevent convective oxygen transport to the electrode. The Ag/Ag+ reference electrode consisted of an Ag wire that was immersed into 0.1 M AgNO3 in CH3CN and sealed with a vycor frit at its tip. All potentials in this study are referenced to the Li/Li+ potential scale (volts vs. Li+/Li or VLi+), obtained by calibration of the reference electrode against a fresh lithium wire before the experiments (0 VLi = −3.46 ± 0.01 V vs. Ag/Ag+). The working electrode consisted of a catalyst-covered glassy carbon disk and was immersed into the Ar or O2-purged electrolyte for 30 min before each experiment. Prior to the RRDE measurements, alternating current (AC) impedance measurements determined the uncompensated ohmic drop between the working and the reference electrodes. A 10 mV perturbation (0.1 MHz to 10 MHz) was applied to the open circuit. The IR-correction to remove ohmic losses used the total cell resistance of ~293 Ω, as measured by AC impedance. The capacitive-corrected ORR currents were calculated by subtracting the current measured under Ar from that obtained in pure O2 under identical scan rates, rotation speeds and catalyst loadings.

3. Results and Discussion

The phase composition and the crystal structure of the as-prepclass="Chemical">ared composites were determined using the XRD patterns that <class="Chemical">span class="Chemical">are shown in Figure 2a. In Figure 2a, all peaks are identified as pure and well-crystallized Mn3O4 phase (JCPDS 24-0734), with a hausmannite-type tetragonal structure that is indexed to the I41/amd soace group. The XRD curves do not show any evidence of the formation of crystalline or amorphous carbon. It appears that when using different organic surfactants as a carbon source, all of the final products probably remain amorphous or as low crystalline carbon.

Figure 2

(a) X-ray diffraction (XRD) patterns for a theoretical pattern, Pluronic F-127 (F127), Pluronic P-123 (P123), and Trition X-114 (TX114) and N2 adsorption-desorption isotherms and the pore-size distribution plots (insert) for (b) TX114; (c) P123; and (d) F127.

class="Chemical">Nitrogen adsor<class="Chemical">span class="Chemical">ption-desorption isothermal measurements were performed to determine the pore structure of the Mn3O4/C composite. Figure 2b–d shows that all of the as-prepared Mn3O4/C samples exhibit a typical type-IV N2 sorption isotherms with distinct H3-type hysteresis loops at a high relative pressure between 0.8 and 1.0, indicating the characteristic of macroporous and mesoporous materials. The Barrett–Joyner–Halenda (BJH) pore size distributions for all samples are shown in the inserts of Figure 2b–d along with a peak that is centered at 50 nm. The minor broad distribution peak that ranges between 100 and 200 nm corresponds to the macropore region and is probably a result of the space between aggregated particles. Many studies [13,22,23] have shown that the wide variation in meso/macro pore size increases the cell capacity of Li–O2 batteries because it results in a large electrolyte/electrode contact area and favorable distribution of the discharge products, such as lithium peroxide, in the cathode discharge. The BET analysis shows respective specific surface areas of about 28.9, 23.3 and 23.0 m3·g−1 for the TX114, P123 and F127.

The morphology of the as-prepclass="Chemical">ared <class="Chemical">span class="Chemical">Mn3O4/C composites was observed by SEM, as shown in Figure 3. The SEM images of the Mn3O4/C composite show that the shape of the Mn3O4/C powder is close to spherical and the size is narrowly distributed between 0.9 and 1.3 μm, although a few agglomerates exist. The mean particle sizes of the TX114, P123 and F127, as determined by PSA, are about 0.86, 1.04 and 1.51 μm, respectively. These values are in good agreement with the measurement from SEM (Figure 3). Table 1 shows the residual carbon content, the particle size and the BET surface area for all of the as-prepared Mn3O4/C composites, using TX114, P123 and F127 surfactants. In order to ensure that there were equal amounts of residual carbon in the composites, the final content of the residual carbon of all of the samples was maintained at approximately 2–3 wt %. The data in Table 1 demonstrates that the composite from TX114 has a smaller particle size, which results in a larger surface area. The particle size increases, which is consistent with the decrease in the specific surface area, from 28.9, 23.3 and 23.0 m2·g−1, for the TX114, P123 and F127, respectively.

Figure 3

Scanning electron microscope (SEM) images for Mn3O4/C composites that use (a) TX114; (b) P123; and (c) F127.

Table 1

A comparison of the residual carbon content, the particle size and the surface area of Mn3O4/C powders that use various surfactants.

Surfactants	Residual Carbon Content (wt %)	Particle Sizes (nm)	Brunauer–Emmett–Teller (BET) Surface Area (m2·g−1)
Trition X-114 (TX114)	2.56	855	26.9
Pluronic P-123 (P123)	2.72	1042	23.0
Pluronic F-127 (F127)	2.81	1511	23.3

Due to the study of the electrocatalytic activity of the as-prepclass="Chemical">ared <class="Chemical">span class="Chemical">Mn3O4/C samples, the following discussion of the electrochemical tests makes comparisons between Super-P carbon (SP) and as-prepared Mn3O4/C materials. Mn3O4 is a highly active ORR catalyst and has recently been used as an O2 cathode catalyst in Li–O2 batteries [5,19,21]. Therefore, it is essential to determine the kinetics of ORR for the as-prepared Mn3O4/C composites. The rotating ring disk electrode (RRDE) technique was used to determine the kinetics of ORR, since the ORR current is strongly affected by hydrodynamic conditions. In an early paper by the authors [6], the kinetics of ORR for a MnO2/C composite was studied and the O2 solubility, the diffusion rates of O2 and O2•− coefficients ( and ), the rate constant (k) for producing O2•− and the propylene carbonate (PC)-electrolyte decomposition rate constant (k) for the MnO2/C material and SP were measured using RRDE experiments in a 0.1 M TBAPF6/PC electrolyte. This study uses similar RRDE experiments to determine the kinetics of ORR for the as-prepared Mn3O4/C composites. The O2•− produced in the first step of the ORR, when the Li–O2 battery discharges:

In the class="Chemical">PC-based electrolyte, the ethereal <class="Chemical">span class="Chemical">carbon atom in PC suffers from nucleophilic attacks by O2•−, which yields carbonate, acetate, and formate species among others, according to Equation (2) [24]:

The reaction rate constant, k, is evaluated using the Koutecky-Levich (K-L) equation for a first order reaction, as follows: where i and i respectively represent the kinetics and the diffusion limiting current density (A·m−2), n is the number of electrons that class="Chemical">are exchanged in the electrochemical reaction, F is F<class="Chemical">span class="Chemical">araday’s constant (96485 C·mol−1), k is the rate constant for reaction 1, is the diffusion coefficient of O2 in the solution, υ is the kinematic viscosity, ω is the angular frequency of the rotation, and is the saturation concentration of O2 in the solution. The stability of an electrolyte against O2•− is defined by the rate constant (k) for Equation (2) and is quantified using the RRDE voltammetry [6,24]. The O2•− that is produced at the disk electrode in Equation (1) and the amount of O2•− are quantified at the ring electrode using the decrease in the collection efficiency, N, for O2•− at the ring electrode as the transient time increases. The correlation with the collection efficiency is the absolute ratio of the ring and disk currents and is characterized by the following equation [6,24,25]: where A1 = 1.288, A2 = 0.643ν1/61/3, β = 3ln(r3/r2), U = k−1 tanh(A1k) and T2 = 0.718 ln(r2/r1), whereby r1, r2, and r3 refer to the radius of the disk and internal and external ring radii, respectively; ν is the kinematic viscosity; ω is the rotation rate; k is the rate constant for reaction 2; and is the diffusion coefficient of O2•−. N is the geometrical collection efficiency of the RRDE corresponding to the fraction of a species electrochemically generated at the disk. This species is detected at the ring due to the lack of side-reactions with the electrolyte. From the measurement of N at a given rotation rate (ω), the rate constant (k) can be calculated by Equation (6).

Prior to estimating the value of rate constants (k and k), the kinematic viscosity (ν) of the electrolyte and the diffusion coefficients of class="Chemical">O2 and <class="Chemical">span class="Chemical">O2•− ( and ) must be quantified. These are listed in Table 2. The estimation of the values in Table 2 is reported in an early paper by the authors [6]. Figure 4 shows the RRDE profiles for the Mn3O4/C and SP samples that are coated on the disk electrode. The disk and ring currents were recorded in an O2-saturated 0.1 M TBAPF6/PC solution at rotation rates between 300 and 2100 rpm. The Pt ring was maintained at 2.6 VLi . The K-L plots for the disc current values at 1.30 VLi (see Figure 4) show the expected linear relationship between the inverse of the limiting current (i) and ω0.5 (see Equation (5)). The rate constant for the production of O2•−, k for the GC and the MnO2/C-GC electrodes is obtained by linearly fitting the K-L plots of i−1 vs. ω0.5 (see Equation (5)) as shown in Figure 5a. The values of k for all of the as-prepared Mn3O4/C composites that use TX114, P123 and F127 surfactants and SP electrodes are 3.7 × 10−2 cm·s−1, 2.9 × 10−2 cm·s−1, 2.3 × 10−2 cm·s−1 and 2.1 × 10−2 cm·s−1, respectively. This result indicates that the Mn3O4/C cathode catalyst has a larger k value than SP, because there is a higher electrocatalytic activity for the first step of the ORR (see Equation (1)), so a higher concentration of O2•− is produced. The TX114 sample has the smallest particle size so it has the largest specific surface area of all of the samples. This results in the highest activity for the ORR in the O2 electrodes.

Table 2

Summary of the electrolyte properties estimated with the proposed rotating ring-disk electrode (RRDE)-based methodology and comparison with the findings reported in the literature.

Disk Material/Electrolyte	υ (cm2·s−1)	D_O_2 (cm2·s−1)	D_O2•− (cm2·s−1)	C_O_2 (mM)	Reference
GC/0.1 M TBAPF6, PC	2.6 × 10−2	1.9 × 10−5	8.6 × 10−6	6.1	[6]
GC/0.2 M TBATFSI, PC	2.6 × 10−2	2.5 × 10−5	6.8 × 10−6	4.8	[24]
MnO2/C-GC/0.1 M TBAPF6, PC	2.6 × 10−2	1.9 × 10−5	1.8 × 10−6	6.1	[6]
M3O4/C-GC/0.1 M TBAPF6, PC	2.6 × 10−2	1.9 × 10−5	4.1 × 10−6	6.1	This work

GC: glassy carbon; TBAPF6: tetrabutylammonium hexafluorophosphate; PC: propylene carbonate; TBATFSI: tetrabutylammonium bis(trifluoromethansulfonyl)imide.

Figure 4

RRDE profiles for Mn3O4/C composites and Super P (SP), recorded at 50 mV·s−1 in an O2-saturated 0.1 M TBAPF6/propylene carbonate (PC) solution, at rotation rates between 300 and 2100 rpm (the Pt ring is maintained at 2.6 VLi: (a) TX114; (b) P123; (c) F127; and (d) Super P.

Figure 5

(a) Koutecky-Levich (K-L) plots for TX114, P123, F127 and Super P (SP). These are derived from the disc current values at 1.3 V; (b) The evolution of the absolute ratio between the ring and the disk current (N) and the electrode rotation rate (ω) for TX114, P123, F127 and Super P (SP), recorded at 50 mV·s−1 in an O2-saturated 0.1 M TBAPF6/PC solution (see Figure 4).

The class="Chemical">RRDE profiles show that the ring current increases as the rotation rate increases because the shorter transient time at higher rotation rates reduces the reaction time between <class="Chemical">span class="Chemical">O2•− and the PC electrolyte so a higher concentration of superoxide radical is oxidized at the ring, as shown in Figure 4. Figure 5b shows that the value of N increases as the rotation rate increases and the individual constant value is close to ω = 2500 rpm for all samples. The values for N at ω = 2500 rpm are about 0.07, 008, 0.09 and 0.1 for TX114, P123, F127 and SP, respectively. The PC-electrolyte decomposition rate constant (k) for different samples is evaluated using Equation (6), using the N value at a rotation rate of 2500 rpm and the kinematic viscosity (ν) and values that are listed in Table 2. Table 3 shows the rate constant for the production of O2•−, k, and the PC-electrolyte decomposition rate constant, k, for the TX114, P123, F127 and SP electrodes. It is seen that the k values for the Mn3O4/C-GC that is prepared using different surfactants are larger than that for the SP. These results also show that TX114 is the most active surfactant for the first step of the ORR (the largest rate constant; k). It produces the highest concentration of O2•−, so the PC-electrolyte decomposes fastest because it is attacked by a large amount of O2•−. A similar result was reported in an earlier study by the authors [6].

Table 3

The rate constant for the production of O2•−, k, and the PC-electrolyte decomposition rate constant, k, for the different sample electrodes.

Disk Materials/Electrolyte (Sample)	kf (cm·s−1)	k (s−1)
Mn3O4/C-GC/0.1 M TBAFSI, PC (TX114)	3.7 × 10−2	3.7
Mn3O4/C-GC/0.1 M TBAFSI, PC (P123)	2.9 × 10−2	2.9
Mn3O4/C-GC/0.1 M TBAFSI, PC (F127)	2.3 × 10−2	2.3
Super P-GC/0.1 M TBAFSI, PC (SP)	2.1 × 10−2	2.1

To better determine the electrocatalytic activity of the electrodes, cyclic voltammetry (CV) and chclass="Chemical">arge–disch<class="Chemical">span class="Chemical">arge voltage measurements were performed in the Li–O2 test cell to compare Mn3O4/C composite (prepared from TX114) and Super P carbon (SP). The CV plots for the O2 electrodes that were prepared using TX114 and SP cycled between 1.5 and 4.5 V at 2 mV·s−1 and for the 1 M LiPF6/PC electrolyte are shown in Figure 6a.

Figure 6

(a) CVs recorded at a scanning rate of 2 mV·s−1 for TX114 and Super-P (SP); (b) The initial charge–discharge profiles for TX114 and SP at a current density of 0.2 mA·cm−2.

During dischclass="Chemical">arge for a Li–<class="Chemical">span class="Chemical">O2 cell, a single cathodic peak appeared at ~2.6 V, indicative of one-step oxygen reduction to produce reaction products by ORR. Upon charging, another anodic peak appeared at ~3.3 V, indicative of decomposition reaction products by OER. The comparison of CV curves for Li–O2 cells with TX114 and SP cathodes were shown in Figure 6a. From the CV curves, the reduction peak voltage is shifted toward a positive voltage, exhibiting electrocatalytic activity in the ORR of both samples. However, the TX114 produces more positive onset reduction peak potential and a larger peak current, which clearly demonstrate that the electrocatalytic activity of TX114 is superior to that of SP. The onset oxidation peaks that appear in the CV curves are about 2.6 and 3.1 V for TX114 and SP, respectively. Therefore, TX114, with its lower onset oxidation peak, is more efficient for Li2O2 decomposition and has higher catalytic activity for the OER. The initial charge–discharge voltage profiles for both samples at the current density of 0.2 mA·cm−2 are shown in Figure 6b. The charge–discharge profiles for the TX114 electrode exhibit much lower charge overpotential than do those of the SP electrode, although the reduction of the total overpotential is only about 30%. The round-trip efficiencies of the Li–O2 batteries with a TX114 electrode were lower than those with the SP electrode. These results demonstrate that the Mn3O4/C composite can facilitate the complete reversibility of ORR and OER at low polarization for a Li–O2 battery. This finding is in good agreement with the results for the CV measurement. Obviously, the initial discharge capacity for the TX114 electrode reached a higher value of 1639 mAh·g−1 and the corresponding discharge plateau was up to 2.64 V. By contrast, the SP electrode delivered lower discharge capacity of 752 mAh·g−1 at the same current density, which may refer to its lower ORR catalytic activity.

Figure 7a shows the dischclass="Chemical">arge curve of Li–<class="Chemical">span class="Chemical">O2 batteries utilizing the TX114 electrode at the different current densities of 0.2, 0.4, 0.8 and 1.0 mA·cm−2. With an increase of the discharge current density, the achieved capacity and cell potential were reduced, due to the internal resistance of the cells. The discharge capacities at a current density of 0.4, 0.8 and 1 mA·cm−2 shown in the insert of Figure 7a were found to be 1360, 994, 715 mAh·g−1, respectively. The cycling performances of Li–O2 batteries with TX114 and SP electrodes at a current density of 0.2 mA·cm−2 are shown in Figure 7b. As seen, the discharge capacity of the Li–O2 battery with the TX114 electrode preserved about 1263 mAh·g−1 after 30 cycles, and the capacity retention was about 77%, as opposed to only 530 mAh·g−1 discharge capacity (60%) for the SP electrode. These results indicate the superior cyclic stability of the TX114 electrode compared to the SP electrode. However, the capacity retention remained rather poor for both electrodes, with the discharge capacities dropping dramatically to below 80% after 30 cycles due to the continuous rise of the resistance. Until now, poor cycling stability has remained a significant challenge for Li–O2 cells. Many investigations [1,2,11,17,26,27,28] have shown that the biggest obstacle for cycling in Li–O2 cells is the decomposition of the electrolyte during the charge–discharge process. Our above RRDE results demonstrate that PC is a poor stable electrolyte solvent in Li–O2 battery due to its reaction with the superoxide radical at the O2 electrode, in agreement with the literature [1,11,17,24]. The above galvanostatic charge–discharge tests show that the discharge capacity of Mn3O4/C composite (TX114) was higher than that of our previous MnO2/C composite [6]. This indicates the superior electrocatalytic activity of Mn3O4/C composite compared to MnO2/C composite. Obviously, Mn3O4/C composite that uses TX114 has higher activity as a bi-functional catalyst and delivers better ORR and OER catalytic performance in Li–O2 batteries. Except PC, the choice of a novel electrolyte is very important, to avoid decomposition by O2•− attack when applying an active catalyst on the cathode material in Li–O2 batteries. More detailed RRDE experiments and analysis will be performed in order to estimate the decomposition rates for various electrolytes with different bi-functional oxygen electrocatalysts.

Figure 7

(a) Discharge curves at different current densities ranging from 0.2 mA·cm−2 to 1.0 mA·cm−2 for TX114. The insert is the discharge capacities at various current densities; (b) Cycle performance for TX114 and SP at a current density of 0.2 mA·cm−2.

4. Conclusions

class="Chemical">Mn3O4/C catalyst materials have been synthesized using ultrasonic class="Chemical">spray pyrolysis with v<class="Chemical">span class="Chemical">arious organic surfactants. SEM and BET analysis confirmed that the as-prepared Mn3O4/C composites consist of homogeneous, micro-spherical particles that have a meso/macro porous structure. The composite that uses a TX114 surfactant has a smaller particle size and larger specific surface area.

The rate constant for the production of class="Chemical">O2•− (k) and the <class="Chemical">span class="Chemical">PC-electrolyte decomposition rate constant (k) for the TX114, P123, F127 and SP electrodes are measured by RRDE experiments in a 0.1 M TBAPF6/PC electrolyte. The results show that the Mn3O4/C composite that uses TX114 is the most active for the first step of the ORR (the largest rate constant; k). It produces the highest concentration of O2•−, so the PC-electrolyte is decomposed fastest because it is attacked by a large amount of O2•−. The CV and galvanostatic charge–discharge tests demonstrate the TX114 has a higher activity as a bi-functional catalyst and delivers better ORR and OER catalytic performance in Li–O2 batteries. The choice of electrolyte is crucial when an active catalyst is used for the cathode material in Li–O2 batteries. In the near future, more detailed RRDE experiments and analysis will be performed in order to estimate the decomposition rates for various electrolytes, except PC. These results are relevant to the design of high-performance, rechargeable Li–O2 batteries.