Imine-Linked Polymer Based Nitrogen-Doped Porous Activated Carbon for Efficient and Selective CO2 Capture.

The preparation of nitrogen-doped activated carbon (NACs) has received significant attention because of their applications in CO2 capture and sequestration (CCS) owing to abundant nitrogen atoms on their surface and controllable pore structures by carefully controlled carbonization. We report high-surface-area porous N-doped activated carbons (NAC) by using soft-template-assisted self-assembly followed by thermal decomposition and KOH activation. The activation process was carried out under different temperature conditions (600-800 °C) using polyimine as precursor. The NAC-800 was found to have a high specific surface area (1900 m2 g-1), a desirable micropore size below 1 nm and, more importantly, a large micropore volume (0.98 cm3 g-1). NAC-800 also exhibits a significant capacity of CO2 capture i.e., over 6. 25 and 4.87 mmol g-1 at 273 K and 298 K respectively at 1.13 bar, which is one of among the highest values reported for porous carbons so far. Moreover, NAC also shows an excellent separation selectivity for CO2 over N2.

The increasing level of atmospheric <n class="Chemical">span class="Chemical">CO2 is great concern due to its impact on global warming and climate change. Serious efforts are, therefore, being made not only to increase the public awareness but also to develop strategies to minimize the emission of <spn>an class="Chemical">flue gases from the power plants utilizing fossil fuels and resources. To minimize the impact on the environment, the anthropogenic CO2 emission after combustion of flue gas must be decreased1. To achieve this, the highly selective CO2 adsorbing materials are being developed/explored and carbon capture and storage (CCS) materials are among the attractive materials in this regard to reduce CO2 concentration from the atmosphere because of their lower transportation and storage cost compared to the CO2 capture cost234.

Over the past decades, a variety of solid-based microporous materials have been used for n class="Chemical">CO2n> capture and storage such as metal organic frameworks (MOFs), hyper-crosslinking polymer (HCPs), covalent organic frameworks (COFs), activated carbons (ACs), functionalized graphene, chemically modified mesoporous materials, and so forth56. Among these, activated carbons, due to their recyclability, availability, easier synthesis and strong adsorption with large surface areas, have found their widespread applications as microporous materials for carbon dioxide capture and storage or separation by physical adsorption7. Microporous materials including activated carbons (ACs) have been regarded as competent candidates for carbon dioxide capture and storage at ambient temperatures, due to their large surface areas, high physical and chemical stability and low density8. To enhance the uptake capacity of activated carbons for carbon dioxide at ambient temperatures, researchers have increased the surface area and regulated the appropriate pore size. Presently, some researchers have even tried to increase the adsorption capacity for carbon dioxide by creating special active sites such as heteroatoms and different organic groups into the activated carbons to improve the interactions between the adsorbate and the functional groups in porous carbons91011.

Hydrothermal <span class="Chemical">carbonn>ization (HTC) is a good way to obtain useful <span class="Chemical">carbon materials and to prepare functionally diverse <span class="Chemical">carbon materials so far12, both physical and chemical activation techniques have become well-established for the preparation of activated carbons. In the physical activation, the precursor materials are carbonized at high temperatures with a flow of gases (CO2 or steam), while in chemical activation the precursors are first impregnated or physically mixed with chemical agents and then heated at the target temperature under inert atmosphere. To improve the porosity of the activated carbons, many activation parameters are to be taken into consideration, such as carbonization temperature, the type of activation agent, the weight ratio between activation agents and the sample, and the time of carbonization held at the target temperature1113 etc., all of which have their own significance in the development of porosity of activated carbons. But it is still unclear which factor has the largest effect on controlling the porosity in activated carbons.

Many types of synthetic <span class="Chemical">polymersn> have been selected as the <span class="Chemical">carbon source since they contain <span class="Chemical">amine groups such as poly acrylonitrile (PAN)14, melamine formaldehyde resin15, polypyrrole16 and poly aniline17. Nitrogen has become one of the most widely studied heteroatoms in the optimization of carbonaceous materials used as supercapacitors and gas adsorption and storage18. Nitrogen-containing carbonaceous materials are prepared by two primary methods: the post treatment and in situ method. In the former one, carbonaceous materials are treated with nitrogen containing compounds such as ammonia19, urea and melamine20 to incorporate nitrogen functional groups. It is commonly used to produce various porous carbons, such as carbon nanotubes, graphene, and activated carbons. In the latter one, many nitrogen-containing precursors are directly used as precursors to produce nitrogen-functionalized carbonaceous materials21, including poly aniline (PNI), poly pyrrole (PPy)22, melamine analogues23 and poly acrylonitrile14. However, CO2 adsorption properties of N-doped porous materials have been rarely investigated so far due to its Lewis-acidic and quadrupolar momentum24. Kaskel et al. investigated porous polyimine as the precursor18. Sun et al. synthesized hierarchical macroporous N-doped carbons (MCN) with ordered three-dimensional periodic structures25. However, CO2 is expected to interact robustly with high polar imines functionalities in the polymer26. Gas adsorption and desorption of porous materials depend not only on the high specific surface area, micropore volume or pore size but also on the chemical composition and structural features of the materials27. To create porous carbons with high porosity and a pore size to facilitate diffusion and adsorption/desorption of gas molecules, most of the synthesis is achieved by procedures using an approximate template which is quite intricate and time consuming or using activation, which is considered to be easier and cheaper compared with the template method28. However, it is still a major challenge to explore a simple synthetic procedure to produce highly efficient porous materials for CO2 capture and storage.

Here, we present a facile strategy, which involves a new type of <n class="Chemical">span class="Chemical">polyimine direct pyrolysis with <spn>an class="Chemical">KOH as a chemical activating agent in the tubular furnace by adjusting the activation temperature, to prepare (i) highly ordered N-doped porous activated carbon using polyimine as an organic precursor (ii) naturally occurring nitrogen is preserved as dopants to motivate molecular adsorption, e.g. for CO2 capture. The resultant N-doped porous carbon exhibits a high CO2 adsorption capacity, and more interestingly a high selectivity for CO2 over N2.

Result and Discussion

Morphology of sample

The overall process for the synthesis of <span class="Chemical">nitrogenn>- doped porous activated <span class="Chemical">carbons (<span class="Chemical">NACs) is shown in Fig. 1. In the first step, imine-linked monomer was prepared by the reaction of aniline and benzaldehyde in the presence of DMSO as a solvent. Then, hyper crosslinked polymer was synthesized by Friedel-Crafts reaction to produce polyimine as the carbon precursor. NACs samples were prepared from polyimine carbonization in the range temperature range (600–800 °C).

Figure 1

Representative schematic diagram of NACs synthesis.

The morphological features of the <span class="Chemical">Nn class="Chemical">ACs were characterized by FE-SEM and HRTEM. The scanning electron microscope (SEM) images exhibit an increased porosity with an increase in the pyrolysis temperature. <spn>an class="Chemical">NACs consist of a lot of cavities and relatively uniform pores and highly interconnected sub-voids, indicating generation of porosity after the reaction of the alkaline reagent KOH during activation as is shown in Fig. 2A–C. The high-resolution transmission electron microscope (HRTEM) was employed to further examine the morphology and textural features of as-synthesized microporous NACs. As evident from Fig. 2(D), bright contrast points on the under focused images represent the pore location, whereas dark contrast cores display empty cavities. It is obvious, however, that they NACs have highly disordered and dense pores.

Figure 2

SEM images of (A) NAC-600 (B) NAC-700 (C) NAC-800 and TEM image of (D) NAC-800.

n class="Chemical">Nitrogenn> adsorption/desorption isotherms of the N-ACs are presented in Fig. 3. All isotherms quite closely correspond to the Type I adsorption according to IUPAC classification. Rapid N2 uptake at relatively low pressures (P/P0 < 0.05) can be observed, which is typical characteristic of microporous materials and there is no tangible hysteresis loop between adsorption and desorption isotherm for these carbons, which is an indicative of their ultra-microporous nature. BET surface area and micropore volume values calculated from relative pressure between 0.01 and 0.1 are listed on Table 1. NAC-800 shows the highest BET surface area of 1900 m2 g−1 with a total pore volume (Vt) up to 0.98 cm3 g−1, while the BET surface area, the total pore volume for NAC-700 (1719 m2 g−1, 0.85 cm3 g−1) and NAC-600 (1681 m2 g−1, 0.80 cm3 g−1) indicate that the heat treatment at elevated temperatures in the presence of KOH imparts surface roughness to the carbon material and leads to an increase in surface area and porosity. For chemical activation, the specific surface area, the total pore volume and the micropore volume of the carbon samples increase remarkably at higher activation temperature (800 °C). The pore size distributions are shown in Fig. 3. The pores are exclusively microporous with less mesoporous (pores, 2 nm) and the highly activated sample NAC-800 reveals a small amount of mesopores up to 2 nm. Moreover, the most of the pores are less than 2 nm in all samples indicating the pore development at both micro- and meso-pore ranges. NAC-800 possesses a relatively high volume of micropores, while NAC-700 and NAC-600 shows a marked decrease in the micropore volume.

Figure 3

Nitrogen adsorption (solid symbols) and desorption (open symbols) isotherms and pore size distributions of NACs, analyzed on N2 adsorption isotherms measured at 77 K using the NLDFT model.

Table 1

Texture Properties, Elemental Composite and XPS Analysis Data of NACs.

Sample	BET m2 g−1	Pore volume cm3 g−1	Element analysis			XPS analysis
			C%	N%	O%	C%	N%	O%
NAC-600	1681	0.80	85.35	2.16	11.93	85.32	2.31	11.24
NAC-700	1719	0.85	88.72	2.07	9.81	87.11	2.02	10.18
NAC-800	1900	0.98	90.36	1.73	6.20	87.62	1.53	10.23

The FTIR spectra (Fig. 4 left) of <n class="Chemical">span class="Chemical">NACs show that the characteristic broad band at ca 3417 cm−1 can be assigned to N-H and/or O-H stretching vibration. The weak band at 2925 cm−1 corresponds to C-H bond, and the weak band of 1627 cm−1 is attributed to the distinctive absorbance of C-H bonds of <spn>an class="Chemical">benzene rings as well as the C=N bonds from the carbon framework. The peaks at 1160 cm−1 suggest the presence of the C-N stretching vibration. The broad peak of 1100 cm−1 is associated with C-N stretching vibration. The FTIR analysis, therefore, confirms the existence of N-H and C-N species in the carbon samples. The elemental analyses show the heteroatom- doped characteristics of NACs, which consist mainly of C, N and O. It is also obvious that there is an increase in the element of C, while N and O content gradually decreased with increasing carbonization temperatures. Nitrogen is present in all NAC samples ranging typically from 1.73% to 2.16%, which suggests the presence of thermally stable nitrogen in the NAC samples during carbonization and activation.

Figure 4

FTIR spectra (left) and Raman spectroscopy (right) showing characteristic D and G peak of NACs samples.

To further understand the chemistry of n class="Chemical">Nn class="Chemical">ACs, their Raman spn>ectrum and the corresponding fitted data are shown in Fig. 4 right. The spectrum shows two peaks, one peak (G-band) at ∼1582 cm−1 due to the E2g phonon of sp2 carbon atoms, characteristic of features of the graphitic layers and corresponds to the tangential vibration of the carbon atoms and the other (D-band) is located at ∼1336 cm−1, which can be attributed to A1g symmetry, corresponding to the disordered carbon or defective graphite structures. The intensity ratio of “D/G”, also called the “R-value”, reflects the range of structurally ordered graphite in the porous carbon materials and reveals the graphitization degree of the carbonaceous materials. Notably, the intensity of D band is higher than that of G band due to the defects and partially disordered structure of the samples. It is worth noting that the intensity ratio (D/G) of as-synthesized samples decreases with increasing temperature. Therefore, the intensity ratio of NAC-800 is lower compared to that of NAC-600 and NAC-700.

In order to obtain further information about the elemental composition and nitrogen-carbon bonding configurations formed on the surface of the NAC samples, X-ray photoelectron spectroscopy (XPS) analysis was employed to quantitatively analyze the nitrogen-doping. XPS spectrum displays several peaks at 284 eV, 399 eV and 532 eV, which can be attributed to C, N, and O respectively as shown in Fig. 5A. For all samples, the XPS N 1 s core signal is de-convoluted into three peaks with binding energies at range 398.6–399.4 eV assigned to the pyridinic-N (N-6), with the nitrogen atom in a six-membered ring and contributing with one p-electron to the aromatic p-system. The pre-dominant peaks are situated between 401.2 eV and 401.7 eV, which is assigned to pyrrolic-N (N-5), with two p-electrons contributing to the p-system. The third signal around 403.3–404.2 eV corresponds to a classic graphitic-type N-oxides (Fig. 5B–D). The weight percentages of C, O, and N in the samples are summarized in Table 1. The surface nitrogen content is obtained from XPS measurement in a range 1.53–2.31 wt%. These values are comparable with the CHN results, indicating the homogeneous dispersion of nitrogen species in the carbon matrix. However, high temperature thermal treatments (carbonization and activation) result in the increase in the C ratio and decrease in N ratio.

Figure 5

XPS spectra of NACs (A) survey of NAC-800 and N1s XPS spectra of NAC-600 (B), NAC-700 (C) NAC-800 (D).

CO2 adsorption

The n class="Chemical">CO2n> adsorption isotherms of NACs, measured by the volumetric method at 273 K, 298 K and 1.13 bar, are shown in Fig. 6. The presence of nitrogen-containing basic groups and large fraction of microporosity results in an increase in the synthesis temperature from 600 to 800 °C. All samples exhibit excellent CO2 capture capacities, which is regarded as one of the highest ever reported for porous carbon materials prepared from synthesized polymer. Figure 6 shows the CO2 adsorption isotherms of the activated carbon samples prepared under soft chemical activation conditions. Mildly activated carbons have high CO2 capture in the 5.01–6.35 mmol g−1 and 3.32–4.82 mmol g−1 ranges at 273 and 298 K respectively. NAC-800 shows that the highest CO2 capture is 6.35 mmol g−1. These data prove that specific surface area, tuneable pore size, optimum nitrogen content and chemical characteristics of the resulting porous activated carbon can be optimized in a systematic way to enhance the CO2 adsorption capacity. For comparison, the CO2 capture of original polymer (precursor) measured under the similar conditions shows a negligible adsorption, much less than 1.21 mmol g−1. Additionally, it is important to mention that the synthesized NAC-800 exhibits a larger adsorption capacity at low partial pressures (2.7 mmol g−1 at P/P0 = 0.2 and 273 K) than other recently synthesized materials. Noteworthy, for the NACs, the uptake of CO2 at a pressure of 0.2 bar is relatively high (2.7, 2.5 and 2.0 mmol g−1 at 273 K for NAC-800, NAC-700 and NAC-600 respectively). NAC-800 surpasses most porous carbons and is comparable with some high performing sorbents under the same or similar conditions (0.2 bar), such as NMC-800 (2.5 mmol g−1)29, PP1-2 (1.5 mmol g−1)26, AC (1.5 mmol g−1)30 and CS3-A6 (2.6 mmol g−1)31. It competes with the porous carbon materials and was comparable with some top performing CO2 adsorption such as NMC-800 (2.5 mmol g−1)29, NPC-650 (2.4 mmol g−1)18, MR-1-500 (2.2 mmol g−1)30. For this reason, we believe that this material has a potential to be applied as an industrial CO2 adsorbent for post combustion capture applications. However, further increment of the temperature cannot improve the CO2 adsorption.

Figure 6

CO2 adsorption at 273 K (left) CO2 adsorption at 298 K (right).

Heat of adsorption (Qst)

To obtain more information about the interaction between the adsorbate and the adsorbent surfaces, the isosteric heat of adsorption (Qst) is derived from the CO2 adsorption isotherms at 273 K and 298 K. Qst (kJ mol−1) was calculated from the adsorption isotherms at different temperatures by using the Clausius−Clapeyron equation (the calculation process details see Supplementary information). The curves of Qst versus adsorption amount are shown in Fig. 7. As expected, at zero-loading, NAC-800 shows an heat of adsorption (Qst) of 42.6 kJ mol−1, comparatively higher than that of NAC-600 and NAC-700 (40.1 and 37.6 kJ mol−1) respectively. However, the Qst values are obviously bigger than those mentioned previously for typical carbonaceous adsorbents182932. The high Qst value of NAC-800 is in consistent with the steep curve of the CO2. The relatively constant Qst indicates homogeneous binding sites over the full range of CO2 loading, which can be attributed to the high surface area, small pore size effect and the high polar framework. The dipole moment increases in the presence of N atoms on the AC surface and can facilitate the interaction between the NACs surface and CO2. Moreover, smaller pore size is also known to enhance the heat of adsorption.

Figure 7

Heat of adsorption of CO2 for NACs calculated by the Clausius-Clapeyron equation.

Selectivity

Recently, selectivity of n class="Chemical">CO2n> over N2 is one of the most interesting features in the field of CO2 capturing materials. Selective adsorption behavior of these NACs for both gases (CO2 and N2) was also investigated using Henry’s law constants for single-component adsorption isotherms at 273 and 298 K and up to 1.13 bar (Fig. 8). In the low-pressure range (0.2 bar), the interaction between the NACs and CO2 play a dominant role for CO2 capture. Thus, the amount of CO2 adsorbed by NAC-800 (higher SSA and larger pore volume) is comparable to that of NAC-700 and NAC-600, indicating that NAC-800 has a greater affinity towards CO2. Among ACs, NAC-800 shows the highest CO2/N2 selectivity ratio of 123 at 273 K, whereas NAC-700 and NAC-600 exhibit ratios of 89 and 73, respectively. This comparatively large affinity of NAC-800 for CO2 may be attributed to the presence of basic nitrogen moieties and a large Qst. The optimal CO2/N2 selectivity value of NAC-800 at ambient temperature is even better than those of recently reported N-containing porous carbon materials33033.

Figure 8

CO2 (solid) and N2 (open) adsorption isotherms of NACs at 273 K.

Conclusions

In summary, the n class="Chemical">iminen>-linked polymers are shown to be good precursors for the preparation of porous carbon materials for CO2 capture and CO2/N2 selectivity. It is demonstrated that the nitrogen doping and porous structure of NACs favor the rapid trapping of CO2 at low pressure. Among NACs, NAC-800 has a greater affinity towards CO2 i.e., 6.35 mmol g−1 at 273 K and 4.82 mmol g−1 at 298 K and the highest CO2/N2 selectivity ratio of 123 at 273 K. More importantly, it has higher CO2 capture (2.70 mmol g−1 at 0.2 bar). These results clearly suggest that the NACs derived from polyimines are promising candidates for CO2 capturing and storage applications. The applicability of NACs can be further enhanced by increasing their specific surface area, optimization of the pore-size distribution and generating the nitrogen moieties on their surface.

Method

Synthesis of activated carbons

Activated porous <n class="Chemical">span class="Chemical">carbon materials containing <spn>an class="Chemical">nitrogen (NACs) were prepared by direct pyrolysis of polyimine at different temperatures. Firstly, imine- containing monomer was synthesized following a previously reported procedure18. Through Schiff base reaction using aniline (2.8 g, 30 mmol) and benzaldehyde (3.18 g, 30 mmol) as the starting materials, dimethyl sulfoxide (DMSO, 120 mL) was added into a 250 mL round-bottom flask fitted with a water-cooled condenser and a magnetic stir bar. After being degassed by nitrogen, the mixture was heated at 180 °C overnight under magnetic stirring. It was then cooled to room temperature and the solid product was collected by filtration over a Büchner funnel and washed with a large amount of ethanol. The resulting yellow powder was then dried at 80 °C for 24 h.

Then, the n class="Chemical">iminen>-linked monomer (3.8 g, 20 mmol) dissolved in anhydrous dichloroethane (DCE, 20 mL), iron (III) chloride (6.69 g, 40 mmol) was then added. The resulting mixture was heated to 80 °C for 18 h. After cooling, the solid product was filtered and thoroughly washed with methanol until the filtrate turned clear. It was then further purified by soxhlet extraction in methanol for 24 h and dried in an oven vacuum at 60 °C for 24 h. Dark brown polymer was obtained in good quantitative yield.

After that, n class="Chemical">polyiminen> powders were directly carbonized in the tubular furnace under nitrogen (N2) atmosphere. The dry chemical activation of polyimine was carried out at 600–900 °C with KOH/polyimine weight ratio of 4:1. In a typical activation process, the mixture of polyimine with KOH pellets was put into a ceramic boat crucible in a horizontal tubular furnace. The mixture was heated to the target temperature for 1 h with the ramp temperature 10 °C/min under nitrogen gas flow. After cooling to room temperature, the obtained samples were thoroughly washed several times with 10 w% HCl to remove any inorganic salts, and large amount of distilled water until neutral pH was attained. Finally, the product was dried in a vacuum oven at 100 °C for 24 h. The obtained N-activated porous carbons were denoted as NAC-T, where NAC is the abbreviation of nitrogen doped activated carbons and T refers to the target temperature in °C. Note: NAC-900 was ignored because of the low surface area (423 m2 g−1) and low CO2 adsorption.

Characterization of materials

The BET surface area (SBET), total pore volume and pore size distribution (<n class="Chemical">span class="Disease">PSD) of the samples were obtained from <spn>an class="Chemical">N2 adsorption/desorption isotherms at 77 K using an automatic Micromeritics ASAP 2020 surface area and porosity analyzer. Firstly, all samples were degassed at 110 °C for 8 h under vacuum (10−5 bar) prior to BET measurements. Part of the N2 adsorption isotherm used was of 99.999% purity (at 77 K and up to 1 bar) in the pressure (P/P0) range 0.04 to 0.2 fitted in the BET equation, and the BET surface area calculation was performed using all data points. The pore size distribution (PSD) was achieved from the nonlocal density functional theory (NLDFT) model in the Micromeritics ASAP2020 software package (assuming split pore geometry) based on the N2 sorption isotherm. In the gas sorption measurements, all gases used were of 99.999% purity. Low-pressure (0 to 1 bar), carbon dioxide (CO2 at 273 and 298 K) and nitrogen (N2 at 273 and 298 K) was used in sorption experiments carried out on a Micromeritics ASAP 2020 using an IGA-003 gravimetric adsorption instrument. Surface morphologies of the samples were examined by Field Emission Scanning Electron Microscopy (FE-SEM) (SIRION 200). High Resolution Transmission Electron Micrographs (HR-TEM) of carbon samples were collected by TECNAI G2 20 electron microscope operated at 200 kV. The components of activated carbon samples were investigated through elemental analysis to obtain % C, % H, % N and % O using Vario Micro cube Elemental Analyzer (Elementar, Germany). Fourier Transform Infrared (FT-IR) spectroscopy (Bruker Vertex 70 spectrometer) and X-ray photoelectron spectrometer (XPS -AXIS-ULTRA DLD high- performance imaging, Shimadzu, Japan) were used to analyze the functional groups on surface and the chemical composition of these materials.

Additional Information

How to cite this article: Alabadi, A. et al. n class="Chemical">Iminen>-Linked Polymer Based Nitrogen-Doped Porous Activated Carbon for Efficient and Selective CO2 Capture. Sci. Rep. 6, 38614; doi: 10.1038/srep38614 (2016).

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.