Rikke Bramming Jørgensen1, Morten Buhagen2, Solveig Føreland3. 1. Department of Industrial Economics and Technology Management, Norwegian University of Science and Technology, Trondheim, Norway. 2. Department of Occupational Medicine, St. Olav's Hospital, Trondheim University Hospital, Trondheim, Norway Department of Public Health and General Practice, Norwegian University of Science and Technology, Trondheim, Norway. 3. Department of Occupational Medicine, St. Olav's Hospital, Trondheim University Hospital, Trondheim, Norway Department of Geology and Mineral Resources Engineering, Norwegian University of Science and Technology, Trondheim, Norway.
Abstract
OBJECTIVES: To investigate the exposure to number concentration of ultrafine particles and the size distribution in the breathing zone of workers during rehabilitation of a subsea tunnel. METHODS: Personal exposure was measured using a TSI 3091 Fast Mobility Particle Sizer (FMPS), measuring the number concentration of submicrometre particles (including ultrafine particles) and the particle size distribution in the size range 5.6-560 nm. The measurements were performed in the breathing zone of the operators by the use of a conductive silicone tubing. Working tasks studied were operation of the slipforming machine, operations related to finishing the verge, and welding the PVC membrane. In addition, background levels were measured. RESULTS: Arithmetic mean values of ultrafine particles were in the range 6.26×10(5)-3.34×10(6). Vertical PVC welding gave the highest exposure. Horizontal welding was the work task with the highest maximum peak exposure, 8.1×10(7) particles/cm(3). Background concentrations of 4.0×10(4)-3.1×10(5) were found in the tunnel. The mobility diameter at peak particle concentration varied between 10.8 nm during horizontal PVC welding and during breaks and 60.4 nm while finishing the verge. CONCLUSIONS: PVC welding in a vertical position resulted in very high exposure of the worker to ultrafine particles compared to other types of work tasks. In evaluations of worker exposure to ultrafine particles, it seems important to distinguish between personal samples taken in the breathing zone of the worker and more stationary work area measurements. There is a need for a portable particle-sizing instrument for measurements of ultrafine particles in working environments. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/
OBJECTIVES: To investigate the exposure to number concentration of ultrafine particles and the size distribution in the breathing zone of workers during rehabilitation of a subsea tunnel. METHODS: Personal exposure was measured using a TSI 3091 Fast Mobility Particle Sizer (FMPS), measuring the number concentration of submicrometre particles (including ultrafine particles) and the particle size distribution in the size range 5.6-560 nm. The measurements were performed in the breathing zone of the operators by the use of a conductive silicone tubing. Working tasks studied were operation of the slipforming machine, operations related to finishing the verge, and welding the PVC membrane. In addition, background levels were measured. RESULTS: Arithmetic mean values of ultrafine particles were in the range 6.26×10(5)-3.34×10(6). Vertical PVC welding gave the highest exposure. Horizontal welding was the work task with the highest maximum peak exposure, 8.1×10(7) particles/cm(3). Background concentrations of 4.0×10(4)-3.1×10(5) were found in the tunnel. The mobility diameter at peak particle concentration varied between 10.8 nm during horizontal PVC welding and during breaks and 60.4 nm while finishing the verge. CONCLUSIONS: PVC welding in a vertical position resulted in very high exposure of the worker to ultrafine particles compared to other types of work tasks. In evaluations of worker exposure to ultrafine particles, it seems important to distinguish between personal samples taken in the breathing zone of the worker and more stationary work area measurements. There is a need for a portable particle-sizing instrument for measurements of ultrafine particles in working environments. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/
Authors: Amina Kunovac; Quincy A Hathaway; Mark V Pinti; Andrew D Taylor; John M Hollander Journal: Am J Physiol Heart Circ Physiol Date: 2020-06-19 Impact factor: 4.733
Authors: Marcello Campagna; Ilaria Pilia; Gabriele Marcias; Andrea Frattolillo; Sergio Pili; Manuele Bernabei; Ernesto d'Aloja; Pierluigi Cocco; Giorgio Buonanno Journal: Int J Environ Res Public Health Date: 2017-05-30 Impact factor: 3.390