Literature DB >> 26702194

Design Optimization of a Portable Thermophoretic Precipitator Nanoparticle Sampler.

Art Miller1, Alek Marinos1, Chris Wendel1, Grant King1, Aleksandar Bugarski2.   

Abstract

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are developing methods for characterizing diesel particulate matter in mines. Introduction of novel engine and exhaust after treatment technologies in underground mines is changing the nature of diesel emissions, and metrics alternative to the traditional mass-based measurements are being investigated with respect to their ability to capture changes in the properties of diesel aerosols. The emphasis is given to metrics based on measurement of number and surface area concentrations, but analysis of collected particles using electron microscopy (EM) is also employed for detailed particle characterization. To collect samples for EM analysis at remote workplaces, including mining and manufacturing facilities, NIOSH is developing portable particle samplers capable of collecting airborne nano-scale particles. This paper describes the design, construction, and testing of a prototype thermophoretic precipitator (TP) particle sampler optimized for collection of particles in the size range of 1-300 nm. The device comprises heated and cooled metal plates separated by a 0.8 mm channel through which aerosol is drawn by a pump. It weighs about 2 kg, has a total footprint of 27 × 22 cm, and the collection plate size is approximately 4 × 8 cm. Low power consumption and enhanced portability were achieved by using moderate flow rates (50-150 cm3/min) and temperature gradients (10-50 K/mm with ΔT between 8 K and 40 K). The collection efficiency of the prototype, measured with a condensation particle counter using laboratory-generated polydisperse submicrometer NaCl aerosols, ranged from 14-99%, depending on temperature gradient and flow rate. Analysis of transmission electron microscopy images of samples collected with the TP confirmed that the size distributions of collected particles determined using EM are in good agreement with those determined using a Fast Mobility Particle Sizer.

Entities:  

Year:  2012        PMID: 26702194      PMCID: PMC4685717          DOI: 10.1080/02786826.2012.680551

Source DB:  PubMed          Journal:  Aerosol Sci Technol        ISSN: 0278-6826            Impact factor:   2.908


  5 in total

Review 1.  Pulmonary effects of inhaled ultrafine particles.

Authors:  G Oberdörster
Journal:  Int Arch Occup Environ Health       Date:  2001-01       Impact factor: 3.015

Review 2.  Epidemiological evidence on health effects of ultrafine particles.

Authors:  Angela Ibald-Mulli; H-Erich Wichmann; Wolfgang Kreyling; Annette Peters
Journal:  J Aerosol Med       Date:  2002

3.  Principles for characterizing the potential human health effects from exposure to nanomaterials: elements of a screening strategy.

Authors:  Günter Oberdörster; Andrew Maynard; Ken Donaldson; Vincent Castranova; Julie Fitzpatrick; Kevin Ausman; Janet Carter; Barbara Karn; Wolfgang Kreyling; David Lai; Stephen Olin; Nancy Monteiro-Riviere; David Warheit; Hong Yang
Journal:  Part Fibre Toxicol       Date:  2005-10-06       Impact factor: 9.400

4.  Ultrafine particles at workplaces of a primary aluminium smelter.

Authors:  Yngvar Thomassen; Wolfgang Koch; Wilhelm Dunkhorst; Dag G Ellingsen; Nils-Petter Skaugset; Lars Jordbekken; Per Arne Drabløs; Stephan Weinbruch
Journal:  J Environ Monit       Date:  2005-12-07

5.  Meeting report: hazard assessment for nanoparticles--report from an interdisciplinary workshop.

Authors:  John M Balbus; Andrew D Maynard; Vicki L Colvin; Vincent Castranova; George P Daston; Richard A Denison; Kevin L Dreher; Peter L Goering; Alan M Goldberg; Kristen M Kulinowski; Nancy A Monteiro-Riviere; Günter Oberdörster; Gilbert S Omenn; Kent E Pinkerton; Kenneth S Ramos; Kathleen M Rest; Jennifer B Sass; Ellen K Silbergeld; Brian A Wong
Journal:  Environ Health Perspect       Date:  2007-11       Impact factor: 9.031

  5 in total
  2 in total

1.  Emissions from a Diesel Engine using Fe-based Fuel Additives and a Sintered Metal Filtration System.

Authors:  Aleksandar D Bugarski; Jon A Hummer; Jozef S Stachulak; Arthur Miller; Larry D Patts; Emanuele G Cauda
Journal:  Ann Occup Hyg       Date:  2015-09-30

2.  Complex Aerosol Characterization by Scanning Electron Microscopy Coupled with Energy Dispersive X-ray Spectroscopy.

Authors:  Anders Brostrøm; Kirsten I Kling; Karin S Hougaard; Kristian Mølhave
Journal:  Sci Rep       Date:  2020-06-04       Impact factor: 4.379

  2 in total

北京卡尤迪生物科技股份有限公司 © 2022-2023.